Miata Short Shifter...
#1
Rotary Enthusiast
Thread Starter
Join Date: Jul 2004
Location: Lubbock,Tx
Posts: 881
Likes: 0
Received 0 Likes
on
0 Posts
Miata Short Shifter...
Well,
Got it install a few weeks ago and all works perfect. Only problem right now is the shift **** that came with it is metal and gets extremely hot and I am not much for the design.
Anybody happen to know of any good ***** to fit the miata shifter?
Mike
Got it install a few weeks ago and all works perfect. Only problem right now is the shift **** that came with it is metal and gets extremely hot and I am not much for the design.
Anybody happen to know of any good ***** to fit the miata shifter?
Mike
#2
I like the stock ****, theres one on ebay right now, I think its like $10.
here
Heres a few momo *****
***** from miatamania
here
Heres a few momo *****
***** from miatamania
Last edited by MazdaTed; 07-02-06 at 10:24 PM.
#5
Rotary Enthusiast
Thread Starter
Join Date: Jul 2004
Location: Lubbock,Tx
Posts: 881
Likes: 0
Received 0 Likes
on
0 Posts
Well, at first the shifter was extremely tight and I wasn't sure wether I even wanted it or not but over the past few weeks it has either loosened up or I have got used to it lol.
Either way now it seems easier to shift through.
Mike
Either way now it seems easier to shift through.
Mike
Trending Topics
#8
Senior Member
iTrader: (5)
Join Date: Jan 2006
Location: marion,ohio
Posts: 328
Likes: 0
Received 0 Likes
on
0 Posts
did you sand the small plastic cup that the bottom of the shifter goes in it may
free it up some more. I have heard that this is supposed to be done durring
install of the miata short throw anyways
free it up some more. I have heard that this is supposed to be done durring
install of the miata short throw anyways
#9
Banned. I got OWNED!!!
iTrader: (1)
Yes the S5 is an EXACT fit to the Miata shifter
BTW my shifter was pretty tight at first. I took out one of the spring washers that sits on the bushings(and left it out)and put a little grease on all the moving surfaces in and around the bushings. Mine did finally loosen up after a wearing in period!!!
BTW my shifter was pretty tight at first. I took out one of the spring washers that sits on the bushings(and left it out)and put a little grease on all the moving surfaces in and around the bushings. Mine did finally loosen up after a wearing in period!!!
Last edited by 2713ddddavid; 07-03-06 at 09:40 PM.
#11
Senior Member
Join Date: Sep 2003
Location: Syracuse New York
Posts: 423
Likes: 0
Received 0 Likes
on
0 Posts
Any idea what shifter **** will fit on the miata short shifter first part of the two peice shifter the one with the big threads. I search but could not find. Thinks BTW i had to grind down some of the ball were the plastic bushing go's on i took of about a 1/16" of the bottom and it shifts alot easer.
#13
Rotary Enthusiast
Thread Starter
Join Date: Jul 2004
Location: Lubbock,Tx
Posts: 881
Likes: 0
Received 0 Likes
on
0 Posts
Yeah, they do fit.
Here is the type on ebay:
http://cgi.ebay.com/ebaymotors/Mazda...QQcmdZViewItem
Here is a write up on install as well:
https://www.rx7club.com/showthread.p...ighlight=miata
With an S5 the stock shift **** fits as well. A plus unlike my S4.
Mike
Here is the type on ebay:
http://cgi.ebay.com/ebaymotors/Mazda...QQcmdZViewItem
Here is a write up on install as well:
https://www.rx7club.com/showthread.p...ighlight=miata
With an S5 the stock shift **** fits as well. A plus unlike my S4.
Mike
Thread
Thread Starter
Forum
Replies
Last Post
Jeff20B
1st Generation Specific (1979-1985)
73
09-16-18 07:16 PM
Wicked93gs
2nd Generation Specific (1986-1992)
42
10-07-15 11:58 PM