How much hp on my S4 TII???
I have a 1987 tII im building... I want to be as fast or a little faster than a stock third gen. The stock third gens have about 220 at the wheels and 255 at the crank.
here are my mods Rtek 1.7 with 550/720cc injectors all new. Walboro 255 fuel pump, rewired. Full turbo back 3 inch exhaust, to a y pipe and out to two hi flow mufflers Straight 3inch custom Tubo inlet duct. No power steering or air conditioning. Removed smog pump emissions junk. Greddy type rs blow off valve Stage 3 6 puck clutch How much at the wheels do you think I should see? |
I dunno...prolly like ~210
|
200-215 at the wheel's.?
|
Damn you beat me too it! :)
|
Go you have a ECU for those 720cc? Also what type of boost are you running?
|
He says he's running the Rtek 1.7. The chip is from pocketlogger and its meant to run with 720's.
|
reguardless if he had the rtek or not he could simply use a FCD and be just fine pushing 12psi.
I would add a FMIC just my opinion and yea your prolly 250 to 270 at crank. |
depends.
185whp - 220whp |
Just to stir it up, stock third gens don't have 220 rwhp, more like 180.
|
i will say this i have allmost same setup, cept a 3 puck clutch!, (s5 motor, and turbo though in a s4) and a boost controllor set at 13 psi, and i pulled away from a stock FD no problem
|
3rd gen
the third gen has 255 at the crank.. theres no way it looses 75 hp? the faq on the third gen says its 220 at the wheels.. I really want to clear this up.. anybody able to confirm this?
|
Originally Posted by VII
Just to stir it up, stock third gens don't have 220 rwhp, more like 180.
|
Originally Posted by ilovebree
I have a 1987 tII im building... I want to be as fast or a little faster than a stock third gen. The stock third gens have about 220 at the wheels and 255 at the crank.
here are my mods Rtek 1.7 with 550/720cc injectors all new. Walboro 255 fuel pump, rewired. Full turbo back 3 inch exhaust, to a y pipe and out to two hi flow mufflers Straight 3inch custom Tubo inlet duct. No power steering or air conditioning. Removed smog pump emissions junk. Greddy type rs blow off valve Stage 3 6 puck clutch How much at the wheels do you think I should see? |
yea
I totally though it was BS too, I know it has more like 220 at the wheels...
So, with these mods do you think I can accomplish this or maybe a little bit better? I really want 250 at my wheels... I know it can be done with this setup.. just need to know how. 12 lbs of boost? Like I said, I have the full 3 inch exhaust with the fancy tid I made, and plenty of fuel to back up the boost |
Originally Posted by ilovebree
I totally though it was BS too, I know it has more like 220 at the wheels...
So, with these mods do you think I can accomplish this or maybe a little bit better? I really want 250 at my wheels... I know it can be done with this setup.. just need to know how. 12 lbs of boost? Like I said, I have the full 3 inch exhaust with the fancy tid I made, and plenty of fuel to back up the boost you need to look into a bigger turbo, a hybrid will work, and a FMIC. |
on a S5 stock motor...stock injectors...fuel pump, afc, and 12 psi I put down 221 on a dynojet
|
I'd be surprised if it breaks 190hp...
-Ted |
I have almost the exact same setup (with SAFC II and ACT flywheel, clutch instead), and the previous owner said it dynoed 250 at the wheels. My SAFC is just set for adding more fuel for safety, so its taking away power, if anything. I think he was running 12 psi
|
well
well all you are saying anywhere from 185 to 220.. thats not shit.. wtf youre telling me with a aftermarket tid and full exhaust, having the ecu chipped with a bigger pump and injectors to match it this car wont do much better than stock?
I thought the only problem with the stock mount IC was that if you sit for a while it heat soaks... meaning once you get going again it will drop back down to normal temperature, which of course is not good for something like say autocrossing. If this is all I can do, I am just wasting my money. I have had it with this stupid car and it chewing up my money... what the hell else can I do... I know these stock turbos can get about 250 to my wheels.. ive seen it done ive seen it on here, just dont know how to get it. Will a intercooler mounted away from the engine really give me that much horsepower? Or will it just prevent the heatsoak, which is horsepower, but I dont expect anything astronomically high from it. I must say, if this is all true I am disappointed. |
boost it to 12 psi and get an safc to control the fuel for fine tuning and you will see 220 wheels this is almost a positive there have been multiple people on here to get upwards of 240 or so with that setup... It can be done
|
1) I don't see any mention of a fuel controller.
I think the Walbro is going to make the engine run stinkin' rich; running rich kills power. Get something that can tweak your fuel injectors, and it'll easily break 220. 2) To break 230...240hp, you need either a turbo uprade, a good FMIC, or get rid of the stock ECU and go stand-alone EMS. I've *NEVER* seen a stock ECU, stock turbo FC makes over 230 at the wheels. If you got balls to push the turbo over 15psi, it might make over 230, but I question the reliability of the turbo after that. 3) Drop the attitude. I almost never wanted to reply again cause of your poor attitude. If you want answers, try and be a little more humble and drop the vulgarities; you're not impressing us with your foul mouth. You also might want to do a search. You're asking questions that's been rehashed before. Doing a proper search and READING will get you your answers in here. -Ted |
keep in mind also that you are talking about available hp not total. by lightening everything up you allow the engine to rev faster. you may want to think about doing the TB mod from FC3Spro.com . IMO it's not about raw numbers, it's more usability of the power already generated from the engine. I'm a road race guy, I love corners not stait lining.
TR |
Hybrid turbos can be found at www.bnrturbos.com. Brian is a good guy and knows his stuff. You don't have a whole lot more to go to meat your goal.
|
Well with your S4, you will maka little less maybe 230 at the wheels is attainable, but i wouldn't settle for less then 210.
I dyno'd 240 wrhp, and 227 ftlbs ot the wheels on my car, running 11psi, no boost controller, just stockish jspec, http://www.nopistons.com/forums/inde...howtopic=57323 RB Downpipe/presilencer to a custom Catback. HKS mushroom deally Solid Aluminum motor mounts S5 TII motor ACT SS Disc and HD PP HKS SSQV Some crazy Light Weight Flywheel stock Phone Dials ported TB Rtek V1.5 Stock Fuel System 550's and t2 pump TMIC |
Originally Posted by RETed
1) I don't see any mention of a fuel controller.
I think the Walbro is going to make the engine run stinkin' rich; running rich kills power. Get something that can tweak your fuel injectors, and it'll easily break 220. 2) To break 230...240hp, you need either a turbo uprade, a good FMIC, or get rid of the stock ECU and go stand-alone EMS. I've *NEVER* seen a stock ECU, stock turbo FC makes over 230 at the wheels. If you got balls to push the turbo over 15psi, it might make over 230, but I question the reliability of the turbo after that. 3) Drop the attitude. I almost never wanted to reply again cause of your poor attitude. If you want answers, try and be a little more humble and drop the vulgarities; you're not impressing us with your foul mouth. You also might want to do a search. You're asking questions that's been rehashed before. Doing a proper search and READING will get you your answers in here. -Ted Shit Why didn't I see this before I posted, Ted stop thinking you know everything, because you don't, wow "never seen a stock turbo or IC run over 230hp" lol. Hope you didn't search TED?!?!?! Maybe next time huh? |
All times are GMT -5. The time now is 12:18 PM. |
© 2024 MH Sub I, LLC dba Internet Brands