RX7Club.com - Mazda RX7 Forum

2nd Generation Specific (1986-1992) 1986-1992 Discussion including performance modifications and technical support sections.
Sponsored by:
Banzai Racing

Finally started workin on my car

Thread Tools
 
Search this Thread
 
Old 02-13-11, 04:25 PM
  #1  
Full Member

Thread Starter
iTrader: (2)
 
huee's Avatar
 
Join Date: May 2005
Location: 415
Posts: 161
Likes: 0
Received 0 Likes on 0 Posts
Finally started workin on my car
So this weekend, I finally got around to putting some wrench time on my car. Its been sitting around for the past 2 years collecting dust. Kida dismayed after swapping in 2 bad engines...doh! Anywhoo, I started off by getting some new shoes on and putting her on a little diet. A little goo gone and scuffing, she'll be off to the painters.
Attached Thumbnails Finally started workin on my car-171677_10150135086150280_731610279_8392411_2086500_o.jpg   Finally started workin on my car-172030_10150134274285280_731610279_8378336_1709505_o.jpg  
huee is offline  
Reply Like
Old 02-13-11, 04:31 PM
  #2  
Full Member

Thread Starter
iTrader: (2)
 
huee's Avatar
 
Join Date: May 2005
Location: 415
Posts: 161
Likes: 0
Received 0 Likes on 0 Posts
pulling the dash was a pain. Who ever put it in did not use 8mm screws on the top of the dash. Rounded phillips were what i found! simple solution below.
Attached Thumbnails Finally started workin on my car-171551_10150135081185280_731610279_8392361_2638865_o.jpg  
huee is offline  
Reply Like
Old 02-13-11, 04:47 PM
  #3  
No Pistons

iTrader: (10)
 
rnz520's Avatar
 
Join Date: Nov 2008
Location: Culpeper, VA
Posts: 822
Likes: 0
Received 1 Like on 1 Post
nice flashlight, stinger LED?
rnz520 is offline  
Reply Like
Old 02-13-11, 04:50 PM
  #4  
Full Member

Thread Starter
iTrader: (2)
 
huee's Avatar
 
Join Date: May 2005
Location: 415
Posts: 161
Likes: 0
Received 0 Likes on 0 Posts
yep, got one for the shop. and one for the duty belt.
huee is offline  
Reply Like
Old 02-17-11, 06:56 PM
  #5  
No Pistons

iTrader: (10)
 
rnz520's Avatar
 
Join Date: Nov 2008
Location: Culpeper, VA
Posts: 822
Likes: 0
Received 1 Like on 1 Post
have one too, pricey but love it
rnz520 is offline  
Reply Like
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Installed UIM gasket, now my engine won't run
trickster
2nd Generation Specific (1986-1992)
25
07-01-23 04:40 PM
1979 Barn Find - Unable to idle
alphawolff
1st Generation Specific (1979-1985)
17
11-17-15 05:57 PM
New Member and Rotary Owner from Ontario
elpartso_robb
Introduce yourself
6
08-29-15 08:45 AM
August 30th Sunday Goodwood Kartways gokarting event 3-6pm,Touge.ca #16 of 20+ Events
rx8volks
Canadian Forum
0
08-13-15 04:55 AM
Back to Subforum
2nd Generation Specific (1986-1992)
View Next Unread
overheating.... AHHHH




Advanced Search
Quick Reply: Finally started workin on my car


Reply Closed Thread Share

All times are GMT -5. The time now is 07:12 AM.