Could someone with a turbo rear end sitting around measure something for me
#1
Full Member
Thread Starter
iTrader: (2)
Join Date: Jun 2006
Location: Portland OR
Posts: 244
Likes: 0
Received 0 Likes
on
0 Posts
Could someone with a turbo rear end sitting around measure something for me
if anyone has a rear end from a 2nd gen turbo sitting around could i get you to measure a couple things.
here's a pic to help show you what i'm looking for.
A: is the width from flange to flange and then the bolt diameter where the axle bolts on to the flange.
B: the axle center line to the drive line flange.
Also as a side note, can some one tell me the difference if any between the NA rear diff and axles versus the turbos. I'm assuming the turbos would be more stout if anything. but that's me just guessing.
thanks for the help
here's a pic to help show you what i'm looking for.
A: is the width from flange to flange and then the bolt diameter where the axle bolts on to the flange.
B: the axle center line to the drive line flange.
Also as a side note, can some one tell me the difference if any between the NA rear diff and axles versus the turbos. I'm assuming the turbos would be more stout if anything. but that's me just guessing.
thanks for the help
#3
Full Member
Thread Starter
iTrader: (2)
Join Date: Jun 2006
Location: Portland OR
Posts: 244
Likes: 0
Received 0 Likes
on
0 Posts
did some more searching around and found the difference between them, but still would like the measurements.
http://www.rotaryresurrection.com/2n...in_differ.html
http://www.rotaryresurrection.com/2n...in_differ.html
#4
Senior Member
iTrader: (20)
IIRC turbo rearend has 11 ribs on the rear and the N/A has 9 ribs also. Here is a link that might help.
http://www.tristatetuners.com/forum/...ad.php?t=54370
http://www.tristatetuners.com/forum/...ad.php?t=54370
#6
Auto-Ex Noob
iTrader: (1)
Join Date: Nov 2003
Location: new hampshire
Posts: 209
Likes: 0
Received 0 Likes
on
0 Posts
A= a c-hair under 10 15/16th, the bolt spacing is 4.485 C to C, with a .400 hole in the half shaft flange
B= i could only measure from very front of the actual diff housing reason being it has no pinion flange and i got 15.125 donno if that helps
as far as the differences between them i dont have a n/a half shaft to measure but i know the bolt pattern is different, and the diameter of a t2 half shaft is 1.045 .i know the n/a half shaft is smaller. hope that helps
--Joe
B= i could only measure from very front of the actual diff housing reason being it has no pinion flange and i got 15.125 donno if that helps
as far as the differences between them i dont have a n/a half shaft to measure but i know the bolt pattern is different, and the diameter of a t2 half shaft is 1.045 .i know the n/a half shaft is smaller. hope that helps
--Joe
#7
Full Member
Thread Starter
iTrader: (2)
Join Date: Jun 2006
Location: Portland OR
Posts: 244
Likes: 0
Received 0 Likes
on
0 Posts
A= a c-hair under 10 15/16th, the bolt spacing is 4.485 C to C, with a .400 hole in the half shaft flange
B= i could only measure from very front of the actual diff housing reason being it has no pinion flange and i got 15.125 donno if that helps
as far as the differences between them i dont have a n/a half shaft to measure but i know the bolt pattern is different, and the diameter of a t2 half shaft is 1.045 .i know the n/a half shaft is smaller. hope that helps
--Joe
B= i could only measure from very front of the actual diff housing reason being it has no pinion flange and i got 15.125 donno if that helps
as far as the differences between them i dont have a n/a half shaft to measure but i know the bolt pattern is different, and the diameter of a t2 half shaft is 1.045 .i know the n/a half shaft is smaller. hope that helps
--Joe
Thread
Thread Starter
Forum
Replies
Last Post