CD player install....which wire for ignition?
CD player install....which wire for ignition?
I'm trying to install a cd deck into my s5. The previous owner who had the car had his player stolen. So the wires are hacked. No biggie since I will rewire the speakers with better wire. I got the ground hooked up, 12v constant, illumination, but I can't figure out where to tap into a igntion wire. Can anyody give me an idea what color wire or where to splice. I know I can hook up to the 12v constant but would rather not.
ok went out to my car to look for you, im in the process of putting a new cd player in. My old one expired due to old age. The blue with white stripe wire is your ignition and the blue with red stripe is main power. buy a test light if you dont have one though very handy for every needs.
I got so many wires that were cut when the radio was stolen. I'm doing process of elimination by pulling the old speakers and looking at what color wire they have. I figured out the rear speaker wires. Looks like there is more than 1 blue w/ white stripe. I guess i'll try and use my voltmeter.
I also checked my antenna which was ripped off. It is the non power, cuz I checked under the antenna mount. Is it possible to fit one of the rubber mast type. Looks like it won't fit cuz the hole on the wing is too small unless I take the wing off and mount it first.
I also checked my antenna which was ripped off. It is the non power, cuz I checked under the antenna mount. Is it possible to fit one of the rubber mast type. Looks like it won't fit cuz the hole on the wing is too small unless I take the wing off and mount it first.
Last edited by DASUPACAT1; May 27, 2006 at 08:09 AM.
just take a multimeter...ground your black lead to the chassis...turn your ignition to accessory (so that your radio would normally turn on)...then take your postive lead and hit all the open wires...only 2 or 3 should show 12v (one is your constant, which you already have)....while showing 12v on one of the other leads...turn the ignition off....if the 12v drops to 0...you found accessory. That should take alot less time than pulling your door panels off and removing speakers to eliminate leads.
Trending Topics
Joined: Feb 2001
Posts: 29,798
Likes: 128
From: London, Ontario, Canada
Isn't this in the FAQ?
https://www.rx7club.com/showthread.p...72#post5131072
Now if you want an IGN source, then you will have to go to the black/white wire around the ignition switch.
https://www.rx7club.com/showthread.p...72#post5131072
Now if you want an IGN source, then you will have to go to the black/white wire around the ignition switch.
Originally Posted by X-JaVeN-X
just take a multimeter...ground your black lead to the chassis...turn your ignition to accessory (so that your radio would normally turn on)...then take your postive lead and hit all the open wires...only 2 or 3 should show 12v (one is your constant, which you already have)....while showing 12v on one of the other leads...turn the ignition off....if the 12v drops to 0...you found accessory. That should take alot less time than pulling your door panels off and removing speakers to eliminate leads.
Originally Posted by DASUPACAT1
yeah i saw that.
i bought two types of rubber ant. to see which will fit.
i bought two types of rubber ant. to see which will fit.
And next time read the FAQ for FC sticky thread found at the top of this the 2nd gen technical section. It has many of the commonly asked questions such s the stereo wires, that you started this thread with.
Originally Posted by Icemark
why wouldn't you just read the FAQ for FC sticky thread found at the top of this section and read all about the stereo power and speaker wires?
Thread
Thread Starter
Forum
Replies
Last Post
SakeBomb Garage
SakeBomb Garage
0
Sep 4, 2015 05:20 PM




