Kenteth

Ok... Seriously, We've all (or at least I have) Run into so many lost bolts, that I thought it might be helpful to create a thread that can be used as a resource to finding pitch threads quickly (if anyone has ever had to look them up).

Guys in?

I'll start off with something trivial:

Steering column knucles: Cotter M8x1.25

Wheel Studs: M12x1.50

S4 (S5?) N/A Exhaust Manifold: M10x1.25

Engine/Tranny (all but one): M14x1.25 [varying lengths]

P/S Rack Lines (two): M12x1.25
P/S Rack Lines (third, some models): M16x1.50 [impossible to find]

Oil Injectors (N/A): M10x1.00
Oil Injectors (TII): M10x1.25

S4 Shifter: M12x1.25
S5 Shifter: M10x1.25

Tie Rod Ends: M12x1.25

jreynish

iTrader: (2)

does anybody know the thread size and pitch of the engine mount bolts?

Kenteth

Brake caliper bleeders are 8m1. and 7m1 respectively. Also that clutch slaves are 8m1 or 7m1 depending on model.
N/A pilot bearing seal pn: 1881-11-404A (not sure if thats the universal mazda number though)

vaughnc

HA HA - I know what you mean.

I bag & tag everything, but still manage to loose bolts.

Best advice is not only to bag & tag as you pull stuff off the car, but pickup a thread measuring gauge (see pic below) and list the fastener/bolt specs in a chart like:

Front A arm mounting bolts: Qnty 2 - M10 x 14mm head, 18cm length, .25 pitch, - "8" strength stamped on top, built in washer

http://www.boltdepot.com/thread-gauges.aspx

asherwood

hmmm, I believe the pitch is right but the diameterr should be 10mm (at least on my S5 N/A)

IS this a challange to see how many we can come up with!

croffeyc

How about the lower bolt on the starter, not the long one that goes throught the top.

This is for an S5 (Maybe S4 is the same?).

DerangedHermit

Some good info on here. I vote that after this thread has been filled with every single bolt/thread size we get a compilation and archive. I've found bolts on the ground and didn't know what they were from... good job me .

Turbo_Rotary

The studs for the turbine housing to downpipe connection on an S5 turbo are M10x1.5 thread on both sides. The stud is 53mm long with a 10mm threaded end
for the housing side and an 18mm threaded end of the downpipe side.

$150FC

what size is the stock coolant temp sensor?

Busted-7

anyone know the bolt size/thread pitch of the two bolts that hold on the s4 secondary fuel rail?

Busted-7

double

RacerJason

iTrader: (5)

Can someone tell me the thread, pitch, and length for the brackets that mount the front anti-sway bar to the the frame rails please? 8? 10? 1.25? 1.50?

hIGGI

iTrader: (7)

fix your S4 shifter info, its

S4 Shifter: M12x1.5

DerangedHermit

My S4 shifter fit just fine into a S5 tranny.

dorifc3s

what shifters can the S4 shift **** fit to? what others use the m12x1.25?

DerangedHermit

As in other cars?

dorifc3s

yeah, i know ( i think) nisans can fit S5 shifters..

(Edit...remove oversized sig...CHECK YOUR PMs)

My Junx

Is this the bolts that attach it to the block or the ones that connect to the precat/midpipe?

I need the size and pitch of the bolts that connect the manifold to the precat (S5), because one of mine got stript...=noisy leak.

any info?

My Junx

OK so I was under the car and checked it out, the studs that connect the manifold to the midpipe or precats is an M12-1.5

-TAL-

i say one person volunteer to take pm's from everyone and sort them in alpha order till we have them all.

Heck i'd be willing to do it, updated once a week, as long as someone could host it on there site

nopistons

Derangedhermit - I believe that they're referring to the shifter's **** threads, not the fit into the trans. S4 and S5 **** threads are different.

My Junx

I just realized I made a typo...the manifold studs are 12X1.25

Fitness Stain

.

brakar

Anyone know the size of the bolts that hold the seats onto the seat rails. (Not the ones that bolt to the floor, but the actualy seat rails) And the bolt that holds the handle on from the inside of the door? I know there are a long shot. Thanks

Flobb

Can someone tell me the size/thread for the nuts that go on the stock TII spoiler?
The sides use the normal 10mm nut everything else has, but the pedestals are bigger.
I need to know the size for the pedestals.


My spoiler was broken and not on the car when I got it.