Are you all running coil-over springs in the front to fit these wheels???

To answer the konig fitment question....they should fit! I have an S and a GS and they fit both with stock springs and Racing Beat

proof!

Stock:

http://i95.photobucket.com/albums/l1...1/DSC02850.jpg


Racing Beat;

http://i95.photobucket.com/albums/l1...Picture003.jpg
http://i95.photobucket.com/albums/l1...Picture004.jpg
http://i95.photobucket.com/albums/l1...Picture018.jpg

I have them on my 82 GSL with totally stock (and original) suspension, and they fit fine all the way around.

Im assuming it would be the same but in Australia the 1st gen cars with 4/110 stud pattern have the low offset +20
and cars with the 4/114.3 stud have the high +35
we call 1st gens S1, S2, S3, rather than sa fb etc
S1 plastic cap steel bumpers, drum rears and 4x110 stud
S2 wrap-around plastic bumpers, rear discs, power windows 4x110 stud
S3 bigger brakes F&R & brake vent slits in front air dam under bumper, thicker/longer axles, 4x114.3 stud

my car is 4x110eg low offset
I have 15x7 (+10) fronts 195/50/15
and 15x8 (+5ish) rears 205/50/15....ill confirm when i get access to my wheels
perfect fitment, low as, no scrape, couldnt get closer to gaurds without scrape


get the highest offset wheel u can at the required width
slowly add washers to stack the wheel out to where u want it
measure the amount of washers and take this from offset
eg 15x7(+40) +20mm of washers stacked on hub
makes it a 15x7 (+20)

hey Red95T-rex:
check the stamping on the back of your wheel
something very fishy here.....
if u put low offset wheels on a car that needs high offset they will stick out the gaurds......
If u put high offset wheels on a low offset car they sit way under the car and foul on the suspension
since you dont have wheels sticking out the side of your car,
that means the supplied wheels are too high offset......
but +20 isnt high its low, so somethings wrong
maybe they supplied wrong offset by mistake???
wrong wheels in boxes????who knows???

+40 wheels definately fit with approx 1in spacer(20-25mm)
mate bought a set of 17x7(+40) wheels off ebay from a 4/114.3 Rx7
when they arrived they didnt fit...he wasnt aware of the stud pattern offset issue we added 25mm hub adapters which runs the wheels at +15 and they corrected the stud pattern to 4x110 problem solved!!!!
now im tired of typin hahahaha

Very well explained yellow. I have 17"x7"s +40 offset with adaptors. I found I had to go back to 20mm adaptors at the front (partly because of brake conversion) and even with rolled guards and Noltec strut tops at max camber I still get the occasional scrub (very light)
http://img379.imageshack.us/img379/9899/beefishdj3.jpg

!17's that we picked up for the turbo II FB

http://photos-e.ak.facebook.com/phot...385332_367.jpg

http://photos-g.ak.facebook.com/phot...85334_1044.jpg

Your rimz are sick. i would love some like those on my GSL-SE. The way that White On White looks to me is SICK..

Were can I get a similar set? Thanks.

15x7 +0 offset 4x114.3 with Falken Azenis RT215 205/50/15

Stock fenders, going to roll/pull it a little bit. The ground is a bit uneven, so it looks high on the left side.

http://tigermack.zenfolio.com/img/v4/p833595862-5.jpg
http://tigermack.zenfolio.com/img/v4/p667673606-5.jpg
http://tigermack.zenfolio.com/img/v2/p616757015-5.jpg

^^ Dear God that beautiful!

that is one expensive camera!!!!!

Lol... how did you know? It is my bro's Canon EOS XTI

https://img.photobucket.com/albums/v...7/P8311295.jpg

Rear:
14x7 +10mm Toyota Celica Supra rims on a GSL-SE rear axle.

Front:
Unknown front wheels.

Ahhhhhhhh! what are those blue mesh wheels!!!? haha they are so badass!!

haha i'm sorry! i quoted the wrong pic! but they were on the back of one of the FB's on the first page!!!
:)

I have NO clue what the offset is. They are Cragar 14" wheels. They are like 7" wide.


They look sexy though!

http://i144.photobucket.com/albums/r...7112808009.jpg
http://i144.photobucket.com/albums/r...7112808040.jpg

I'm looking for a wheel like the Rota or Konig gunmetal in 4x110 15x8 0 offset. I plan on using a fender flare. Does this exist or do I need spacers?

http://www.re4life.com/Galleries/Mem...eeting1/09.JPG

where can i get one of those bumper lips!!!

Oh yea, im a bit clueless when it comes to wheels and offsets. If the wheel is say -16 offset, would that be sticking out too much and leaving the car undriveable? anywhere i can read more on offsets and pros/cons of having wide wheels

maybe try a 195 instead of 205....i like these wheels alot, i seen a set for sale 15x6.5 +13 front and 15x7 +3 rear...they look really good

FS riverside stars 15x6.5 / 15x7 staggered 4x114.3 to be exact

So im looking for this kind of poke, or more, on my '85 GS, and i want to run 15x9 or 10 in the rear, and 15x8 in front.
any idea what kind of offset and backspacing i would need?
Im getting custom wheels thats why i ask.

Here are mine...

15x7 Hayashi/Perrier wheels aka 503 Meshies - One Piece
+4 off set
195/50 in front
205/50 in rear


http://farm3.static.flickr.com/2492/...5259e2d4_b.jpg

http://farm3.static.flickr.com/2610/...4fe7154c_b.jpg

http://farm3.static.flickr.com/2776/...ca1cd874_b.jpg

http://farm3.static.flickr.com/2534/...0e883ca9_b.jpg

16x7 panasorts
 

i will look up the offset next time i pull the wheels. I want them to stick out a little more. I will be converting to gsl-se suspension soon and will get custom adapters to keep the wheels and make them stick out a little more to get the look I want hopefully

G-MAX Wheels
 

dunno if its of any use to anyone but my wheels are G-MAX Drift 6, 17x8 with +35 offset, they fit perfect with the standard body work, minus GP style kit (standard guards, no wide body)

thanks to this thread i'm looking at some 15x7 +0

Special custom drilled SSRs for my RX-3
Front: 16x7.5
Rear: 15x8.5
http://img.photobucket.com/albums/v3...3/SDC10074.jpg
http://img.photobucket.com/albums/v3...3/SDC10076.jpg
http://img.photobucket.com/albums/v3...3/SDC10072.jpg