1st Generation Specific (1979-1985) 1979-1985 Discussion including performance modifications and technical support sections

Power Hatch and other upgrades

Thread Tools
 
Search this Thread
 
Old Sep 24, 2013 | 03:08 PM
  #1  
augt's Avatar
Thread Starter
Junior Member
Tenured Member 05 Years
 
Joined: Oct 2007
Posts: 28
Likes: 0
From: Indiana
Power Hatch and other upgrades

Hi all,

My 1985 FB did not come equipped with power mirrrors, power locks, power windows, a power hatch release, or a rear hatch courtesy light.

Today at a salvage yard, I was able to snag the power hatch latch/popper assembly and cut a piece of the harness. I also got the hatch light and wires out of the back as well.

Well, my venture in saving the wires turned out to be useless, as I found out that all the plugs for both the light AND the hatch popper are already back there. I just need to cut the plastic on the rear hatch trim, but a new bulb, and plug it in.


My question mainly is, is there wiring for the hatch pop SWITCH under the dash.

If so, where is it? I don't have the switch, but I can use a universal push button that I have laying around.

I already have the power latch assembly bolted in and the wires plugged in.


Also, what is required to add power mirrors? I can grab the switch and mirrors off of an equipped car at the yard. Is there a harness to grab that plugs into a main harness for power and control?

Thanks!
Reply
Old Sep 24, 2013 | 08:47 PM
  #2  
wahootee's Avatar
Rotary Enthusiast
Tenured Member 15 Years
iTrader: (50)
 
Joined: Jul 2002
Posts: 938
Likes: 0
From: Omaha/Midwest
Originally Posted by augt
Hi all,

My 1985 FB did not come equipped with power mirrrors, power locks, power windows, a power hatch release, or a rear hatch courtesy light.

Today at a salvage yard, I was able to snag the power hatch latch/popper assembly and cut a piece of the harness. I also got the hatch light and wires out of the back as well.

Well, my venture in saving the wires turned out to be useless, as I found out that all the plugs for both the light AND the hatch popper are already back there. I just need to cut the plastic on the rear hatch trim, but a new bulb, and plug it in.


My question mainly is, is there wiring for the hatch pop SWITCH under the dash.

If so, where is it? I don't have the switch, but I can use a universal push button that I have laying around.

I already have the power latch assembly bolted in and the wires plugged in.


Also, what is required to add power mirrors? I can grab the switch and mirrors off of an equipped car at the yard. Is there a harness to grab that plugs into a main harness for power and control?

Thanks!
I have a factory 84-5 push button hatch release for your hatch that you can have. Just cover the postage. The connector should already be in the dash next to the fuel door release.

I also have what you need for power mirrors so PM me if you want to look into that.
Reply
Old Sep 27, 2013 | 02:05 PM
  #3  
augt's Avatar
Thread Starter
Junior Member
Tenured Member 05 Years
 
Joined: Oct 2007
Posts: 28
Likes: 0
From: Indiana
PM Sent!

Thanks!
Reply
Old Sep 27, 2013 | 03:17 PM
  #4  
82transam's Avatar
Never Follow
Tenured Member: 20 Years
iTrader: (18)
 
Joined: Feb 2002
Posts: 8,389
Likes: 120
From: North Jersey
The wiring for the hatch release is all under the dash already.

As for the power mirrors, the wiring for the switch as well as the plug going toward the doors (but not into the doors) will already be there, hanging above the speakers. You just need the wiring and rubber grommets for said wiring to go out into the doors themselves (you'll see where it goes through the door jam when you open the door) as well as the mirrors and switch obviously.

FYI, no FB has factory power locks. If you were to want the power windows it's the same deal as the mirrors, all the wiring is inside the car for it, you just need the door side of the wiring as well as the switches and motors etc.
Reply




All times are GMT -5. The time now is 12:21 PM.