pissing fuel out of exhaust/left hand side of engine.
#1
Senior Member
Thread Starter
Join Date: Mar 2006
Location: Canada
Posts: 634
Likes: 0
Received 0 Likes
on
0 Posts
pissing fuel out of exhaust/left hand side of engine.
I started my car up the other day and it ran fine, this was right after i did the manual swap. Started up...ran prety good...idled good.
then i went out the next day and installed the driveshaft and put the oil in the trany, started it up, it ran like ****.
Then i started it up today to find that i had a patch of gas on the ground, now tell me whats wrong here? Its pissing out of the exhaust, i only have a shorty pipe on the mani for now, and maybe somewhere else near the oil pan? If i leave it for a day or so, it sill start bur bur bur and then die, with no luck of starting it again. Wire order is correct i believe, im getting tonnes of spark, the dizzy hasnt been removed, and the car is getting lots of gas...peeing gas actually...any idea?
then i went out the next day and installed the driveshaft and put the oil in the trany, started it up, it ran like ****.
Then i started it up today to find that i had a patch of gas on the ground, now tell me whats wrong here? Its pissing out of the exhaust, i only have a shorty pipe on the mani for now, and maybe somewhere else near the oil pan? If i leave it for a day or so, it sill start bur bur bur and then die, with no luck of starting it again. Wire order is correct i believe, im getting tonnes of spark, the dizzy hasnt been removed, and the car is getting lots of gas...peeing gas actually...any idea?
#2
Too old to act my age
Join Date: Feb 2005
Location: Tulsa, Ok.
Posts: 3,164
Likes: 0
Received 0 Likes
on
0 Posts
Sounds like it's flooding. There are many items that can cause this to occur.
First step, pop the fuel cap. If there is a lot of pressure in the tank, you have a plugged vent. This can lead to flooding, as the entire fuel system is pressurized.
If that is not the issue, then you need to start looking at the carb.
First step, pop the fuel cap. If there is a lot of pressure in the tank, you have a plugged vent. This can lead to flooding, as the entire fuel system is pressurized.
If that is not the issue, then you need to start looking at the carb.
#3
Senior Member
Thread Starter
Join Date: Mar 2006
Location: Canada
Posts: 634
Likes: 0
Received 0 Likes
on
0 Posts
Thats what i was thinking, when i was looking at the carb, it almost looked like it was PISSING, literally pissing into the secondarys, while the secondaries werent even opening. ?
#4
Too old to act my age
Join Date: Feb 2005
Location: Tulsa, Ok.
Posts: 3,164
Likes: 0
Received 0 Likes
on
0 Posts
Either the fuel tank vent system is plugged up, or the carb needs attention. If popping the fuel cap does not release a lot of pressure, take the air cleaner off, and LIGHTLY tap on the top of the fuel inlets on the carb, with the fuel pump running. This will tell you if the needle and seats are sticking. If the fuel stops flowing from the secondaries, then the needle and seats are sticking. In this case, you may be able to add some pour-thru carb cleaner in the fuel tank, and drive the car for a while.
If the fuel does not stop flowing, then you will likely need to rebuild the carb.
It could also be caused from an aftermarket fuel pump that is too high PSI for the system. Stock setup only uses about 3PSI, most aftermarket pumps are 4-7PSI minimum, and need a fuel pressure regulator to prevent the flooding.
If the fuel does not stop flowing, then you will likely need to rebuild the carb.
It could also be caused from an aftermarket fuel pump that is too high PSI for the system. Stock setup only uses about 3PSI, most aftermarket pumps are 4-7PSI minimum, and need a fuel pressure regulator to prevent the flooding.
#5
Senior Member
Thread Starter
Join Date: Mar 2006
Location: Canada
Posts: 634
Likes: 0
Received 0 Likes
on
0 Posts
yeah i have a stock fuel pump so il check the jetting, i dont want to keep trying to start the car because every time i do it pisses more and more fuel onto the ground, im worried its going to fire and put the car up in flames.
#6
Rotoholic Moderookie
iTrader: (4)
If it's pissing fuel it's *not* jet related.
The only jet-kinda thing that could make it **** fuel was if your air bleeds were 100% blocked off. Then the suction from the engine would suck raw fuel out, but that's highly unlikely.
I'd just grab a rebuild kit and go at the carb. If you're sure that your fuel pressure is good (stock pump won't pump enough to make it **** like that, but my mallory did since the FPR was the wrong one) then something's amiss in the carb. My guess would be needle/seat assembly, though I *could* be way off.
Has anyone tampered with the carb or the fuel system since it last worked? Blocked return line maybe (though that shouldn't have an effect since you *can* run a deadhead system with these cars...).
That's all I can come up with.
Jon
The only jet-kinda thing that could make it **** fuel was if your air bleeds were 100% blocked off. Then the suction from the engine would suck raw fuel out, but that's highly unlikely.
I'd just grab a rebuild kit and go at the carb. If you're sure that your fuel pressure is good (stock pump won't pump enough to make it **** like that, but my mallory did since the FPR was the wrong one) then something's amiss in the carb. My guess would be needle/seat assembly, though I *could* be way off.
Has anyone tampered with the carb or the fuel system since it last worked? Blocked return line maybe (though that shouldn't have an effect since you *can* run a deadhead system with these cars...).
That's all I can come up with.
Jon
Trending Topics
#8
Too old to act my age
Join Date: Feb 2005
Location: Tulsa, Ok.
Posts: 3,164
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by chedda_j
i have a wire missing on the right hand side that was hooked up before, that needle thinger...could that be it?
The bowl vent solenoid is located just under the fuel lines, if that is the part you are talking about having a wire missing, fix it.
#10
Senior Member
Thread Starter
Join Date: Mar 2006
Location: Canada
Posts: 634
Likes: 0
Received 0 Likes
on
0 Posts
yeah, where does that wire come from? The part of the wiring harness that runs behind the engine and connects to the sensors on the side of the block? Does anyone know what colour it is? I know that the one from the sensor is black white? THen i have one cut in my wiring harness that is black/white red dot, that is prety close to the sensor? Could i just hook it up to the battery and try to start it and see if it works?
#11
strictly business
iTrader: (8)
Join Date: May 2005
Location: chamber of farts
Posts: 6,187
Likes: 0
Received 0 Likes
on
0 Posts
More pics of your car?
Originally Posted by chedda_j
I started my car up the other day and it ran fine, this was right after i did the manual swap. Started up...ran prety good...idled good.
then i went out the next day and installed the driveshaft and put the oil in the trany, started it up, it ran like ****.
Then i started it up today to find that i had a patch of gas on the ground, now tell me whats wrong here? Its pissing out of the exhaust, i only have a shorty pipe on the mani for now, and maybe somewhere else near the oil pan? If i leave it for a day or so, it sill start bur bur bur and then die, with no luck of starting it again. Wire order is correct i believe, im getting tonnes of spark, the dizzy hasnt been removed, and the car is getting lots of gas...peeing gas actually...any idea?
then i went out the next day and installed the driveshaft and put the oil in the trany, started it up, it ran like ****.
Then i started it up today to find that i had a patch of gas on the ground, now tell me whats wrong here? Its pissing out of the exhaust, i only have a shorty pipe on the mani for now, and maybe somewhere else near the oil pan? If i leave it for a day or so, it sill start bur bur bur and then die, with no luck of starting it again. Wire order is correct i believe, im getting tonnes of spark, the dizzy hasnt been removed, and the car is getting lots of gas...peeing gas actually...any idea?
#12
Senior Member
Thread Starter
Join Date: Mar 2006
Location: Canada
Posts: 634
Likes: 0
Received 0 Likes
on
0 Posts
yeah im out of a camera right now so all i can do is explain my best. Il take some notes and tell you which wires i have missing, i have some hanging from my harness after doing the swap and i dont know where they go.
#13
Too old to act my age
Join Date: Feb 2005
Location: Tulsa, Ok.
Posts: 3,164
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by chedda_j
yeah, where does that wire come from? The part of the wiring harness that runs behind the engine and connects to the sensors on the side of the block? Does anyone know what colour it is? I know that the one from the sensor is black white? THen i have one cut in my wiring harness that is black/white red dot, that is prety close to the sensor? Could i just hook it up to the battery and try to start it and see if it works?
If you cannot find where it is cut, just splice it into a keyed hot.
#14
Senior Member
Thread Starter
Join Date: Mar 2006
Location: Canada
Posts: 634
Likes: 0
Received 0 Likes
on
0 Posts
rur rur start!
Thats all it was, was that one wire. Started right up, looks like somewhere in the midst of taking the engine out i tore the wire off that led to that connection. What wire plugs into the water pump sensor thinger, plus im missing my oil pressure one too. Where does that connect?
All im going to do is just male to female connect it to a hotwire like you said, plus while messing around with the wiring i noticed that i had a short and a connector that was only working once in a while. *click click * when i wiggled the wires. So i have a little maitance to fix. Still lots of wires.
All i have to say is WOW, i couldnt imagine the difference between the manual and auto setup. Feels like i just doubled my power
Now to just work out the minor details *speedo, reverse lights, brake lights, new driveshaft, shifting console mod....oh my there is alot to do..*
Thats all it was, was that one wire. Started right up, looks like somewhere in the midst of taking the engine out i tore the wire off that led to that connection. What wire plugs into the water pump sensor thinger, plus im missing my oil pressure one too. Where does that connect?
All im going to do is just male to female connect it to a hotwire like you said, plus while messing around with the wiring i noticed that i had a short and a connector that was only working once in a while. *click click * when i wiggled the wires. So i have a little maitance to fix. Still lots of wires.
All i have to say is WOW, i couldnt imagine the difference between the manual and auto setup. Feels like i just doubled my power
Now to just work out the minor details *speedo, reverse lights, brake lights, new driveshaft, shifting console mod....oh my there is alot to do..*
Thread
Thread Starter
Forum
Replies
Last Post
trickster
2nd Generation Specific (1986-1992)
25
07-01-23 04:40 PM
Frisky Arab
2nd Generation Specific (1986-1992)
13
08-18-15 05:30 PM
KAL797
Test Area 51
0
08-11-15 03:47 PM