hey man.. nice carb!
|
Couple of suggestions. I'm always leery about using used fuel pumps, even more so in a turbo application. If you plan on using an intercooler, check out XS Power on eBay. Here's a couple that would work on a 1st gen.
http://cgi.ebay.com/ebaymotors/ws/eB...2BSI%26otn%3D4 http://cgi.ebay.com/ebaymotors/XS-Po...spagenameZWDVW As far as a fuel pump, a stock SE pump will meet your needs, or a less expensive external Walbro 255 lph. Either way, I would upgrade the fuel supply line to 3/8", the stock 12A line will be to restrictive for a high pressure/volume FI pump. You'll need to look into adding a surge tank to insure a constant fuel supply. It's all of the little needed mods that really add to the price of going turbo. I've also modded a few fuel tanks to accept the complete 2nd gen in tank TII fuel pump assembly. This eliminates the need for a surge tank and in some cases, a low pressure lift pump to pull fuel from the tank to feed the FI pump and surge tank. If any of that interests you, PM me. You probably should read up some more of modding fuel systems for turbo applications on a 1st gen. If they are done wrong or inadequately, then you'll be rebuilding the engine due to detonation. If you need a reference on tank mods, PM dj55b or Dan S Young. I've done both of their tanks, one is a turbo, the other is an NA-FI. I go completely through the tanks, having them boiled out, resealed, stripped, repainted and undercoated on the outside. Basically a new tank by the time I'm done. |
hummm so butty-full. keep it up man:icon_tup:
|
Originally Posted by Rotarx7
(Post 8515421)
hey man.. nice carb!
|
Update:
So after a while of doing some cosmetic work to the car, I'm ready to get back on track with this turbo setup. I was able to pick up and old HKS 6 port turbo exhaust manifold that I'm going to use (thanks Royce) as well as a Carb Hat that needs a little modifications. Going to have the manifold cleaned up soon (thanks Fris). With this turbo exhaust manifold, the S5 turbo is out of the question. I'm going to be looking for a T4 turbo, perhaps something along the lines of a t04b, and something similar to an HKS 40mm standard wastegate. I'm going to be doing some other upgrades such as ordering the RB street/strip clutch and pressure plate, as well as an RB lightweight flywheel. Once that's all installed as well as new aftermarket FP & FPR, I will be close to completion! Here are some update pics of the parts. http://i195.photobucket.com/albums/z...Picture002.jpg http://i195.photobucket.com/albums/z...7/IMG_2594.jpg http://i195.photobucket.com/albums/z...7/IMG_2596.jpg |
dude...you dont even know how happy i am with this jack!!
no more cheap ass crank up. it used to take me 30mins to rotate my tires. that time is down to 5mins. hahaha!! thanks bro |
Originally Posted by Rotarx7
(Post 8765653)
dude...you dont even know how happy i am with this jack!!
no more cheap ass crank up. it used to take me 30mins to rotate my tires. that time is down to 5mins. hahaha!! thanks bro |
^ If you can get the Iron manifold to work out for you, that would be the better bet. The stainless mani's are of course prone to cracking so if you can get it sand blasted, lap the flange, replace the studs, that manifold will treat you right. 40mil wastegates maybe a little small for controlling lower boost(not sure, someone might need to chime in), just seems like running high comp rotors and low boost the wastegate may have trouble keeping it from spikes/creeps. GL with the project! Keep this thread alive.
|
Originally Posted by buldozr
(Post 8766926)
^ If you can get the Iron manifold to work out for you, that would be the better bet. The stainless mani's are of course prone to cracking so if you can get it sand blasted, lap the flange, replace the studs, that manifold will treat you right. 40mil wastegates maybe a little small for controlling lower boost(not sure, someone might need to chime in), just seems like running high comp rotors and low boost the wastegate may have trouble keeping it from spikes/creeps. GL with the project! Keep this thread alive.
|
this is awesome, good luck :)
|
Originally Posted by glosoli
(Post 8773539)
this is awesome, good luck :)
Ordering my RB Clutch/Pressure plate/Flywheel this weekend! |
Score! Received my new RB Street/Strip clutch, pressure plate, and the bearing. RB Lightweight steel flywheel already at the shop. Here are some pics!
http://i195.photobucket.com/albums/z...7/pp-cd-br.jpg http://i195.photobucket.com/albums/z...clutchdisc.jpg http://i195.photobucket.com/albums/z...ssureplate.jpg http://i195.photobucket.com/albums/z...87/bearing.jpg |
Taking the car in to have the RB clutch, pressure plate, and lightweight steel flywheel installed. FP and FPR are next. Right now the carb hat is being modified at a shop for my sidedraft and the exhaust manifold is being sand blasted/fixed up. Hoping to see big improvements with the new clutch / fuel setup before I turbo the car. :D
|
First off, nice car, great project. Also, where did you get your wheels at?
Also, great score on the manifold. Another source, (if still available) would be Renee at RX3mist. He can custom make you a tubular manifold, and his prices were very affordable. (He made FB II's manifold, that utilized a S4 flange, placed the turbo higher and towards the front right of the engine bay.) SKYLANCE now has it on his car, I had it for a short period but never utilized it. Is your mallory FPR a rising rate regulator that compensates for boost? Enlarging the fuel return and feed line is also a good idea as sugested earlier. You may also want to consider a 255lph fuel pump, or just go all out and get an innovative. Have you considered, or purchased a wideband? Other future options could be getting a FMOC off of a FC also. Good luck, happy holidays- |
Originally Posted by cds00bsmg
(Post 8820307)
First off, nice car, great project. Also, where did you get your wheels at?
Also, great score on the manifold. Another source, (if still available) would be Renee at RX3mist. He can custom make you a tubular manifold, and his prices were very affordable. (He made FB II's manifold, that utilized a S4 flange, placed the turbo higher and towards the front right of the engine bay.) SKYLANCE now has it on his car, I had it for a short period but never utilized it. Is your mallory FPR a rising rate regulator that compensates for boost? Enlarging the fuel return and feed line is also a good idea as sugested earlier. You may also want to consider a 255lph fuel pump, or just go all out and get an innovative. Have you considered, or purchased a wideband? Other future options could be getting a FMOC off of a FC also. Good luck, happy holidays- I'm happy with the FMOC on my car now, works great! Also, I'm going to be using the following. Fuel pump will be a MSD 225lph, and the FPR will be a Mallory 4309. Thanks for the tips and advice on the other stuff :icon_tup: |
you gonna use a turbo2 tranny?
|
Originally Posted by Rotarx7
(Post 8821666)
you gonna use a turbo2 tranny?
|
you gonna use a turbo2 tranny?
|
Originally Posted by Hit Redline
(Post 8821735)
you gonna use a turbo2 tranny?
|
Originally Posted by Cbz
(Post 8821812)
haha.. nah. I mean it would be smart but I just dropped like $400 in RB clutch/flywheel parts that wouldnt fit a T2 tranny so no point.
I am planning on a TII swap after I get the motor sorted. First things first. I just know with the stock tranny I top out at around 120 in 5th gear. Can't wait to see this project done, you are gonna have so much fun. Who's helping you with the build? |
Originally Posted by Hit Redline
(Post 8821827)
Robert says you can use your current clutch set up with a TII tranny, just need an RX-3 bell housing. That's what he told me.
I am planning on a TII swap after I get the motor sorted. First things first. I just know with the stock tranny I top out at around 120 in 5th gear. Can't wait to see this project done, you are gonna have so much fun. Who's helping you with the build? |
Originally Posted by Hit Redline
(Post 8821827)
Robert says you can use your current clutch set up with a TII tranny, just need an RX-3 bell housing. That's what he told me.
I am planning on a TII swap after I get the motor sorted. First things first. I just know with the stock tranny I top out at around 120 in 5th gear. Can't wait to see this project done, you are gonna have so much fun. Who's helping you with the build? btw i have a s4 TII trans for sale,and a complete rx4 trans thats for sale also,i was going to use them so i can mount the turbo trans on my rx2,but it's just over kill for my little 12a motor. |
dave, yea I was talking to you about that trans. I'm just not in the market for dropping $$ on a trans im not going to use anytime soon.. right now my main concern is dropping $400 on fuel stuff/install. I'm still thinking about it though, will let cha know. thanks man!
|
Originally Posted by Kerebrus
(Post 8821645)
I'm happy with the FMOC on my car now, works great! Also, I'm going to be using the following. Fuel pump will be a MSD 225lph, and the FPR will be a Mallory 4309.
Thanks for the tips and advice on the other stuff :icon_tup: Lastly, you never said, where, or what kind of vehicle, are your wheels from? |
Originally Posted by cds00bsmg
(Post 8837423)
I did not notice you had the FMOC, my mistake. You may want to consider going with the aeromotive (think that is the brand) EFI pump. Talk to Robert and see what the limits of the 255lph are, and if you would ever exceed them.
Lastly, you never said, where, or what kind of vehicle, are your wheels from? |
All times are GMT -5. The time now is 12:04 PM. |
© 2024 MH Sub I, LLC dba Internet Brands