he is so lucky to have his dad give him the parts he needs instead of keeping them for himself but he helps me out to so it works out in the end

 

I sent out the package today.......They said 2 days.......Good luck with the project, I have had 2 SAs and two FBs .......Currently have 1 SA and my S4 vert, I love the vert but there is something about a first gen that can't be beat...........

 

i got the top part of dash off and i got the carpet out i just need to put the new carpet and top part of the dash in, but im not sure she wanted new parts it took me all day to get out the dash out and when i got to the carpet i just tore it out and what wouldnt tear out i took a razor knife too the carpet was already trash anyways i didnt get the ignition im hoping monday and then im gona see if she'll start and if she does im gona be the happiest SA owner kuz then i've got a running 79' that i paid $90.00 (since it gave me the $10.00), plus the $22.00 for front speakers, my dads old CD player, the alpines out of his 85' (the black 1) for the rear, and then put on a drivers side mirror. and after that its minor body work , detailing and then a little work on fixing the console with a little JB wield. and once all the new locks are in she'll be getting a freash coat of paint

 

the speakers are altec lanzings from my v-8 brand new from p/o good shape but not sure if they work they have been sitting in the car for quite a while now the cd player is a pioneer super tunner 3 not top of the line now but a good little unit we know it works had it in the parts hauler

 

i got the ignition and locks today is not compleatly in the car but will b soon
shes not startin at the moment might b sum compression isssues

 

rear rotor has REALLY low comppression it wont start im probly gona have to rebuild the motor but i have a small question for any 1 who may know the answer.
will the rats nest from a 79' swap onto a motor out of an 81'? but thats only a temp im puttig the original motor back in it ASAP
and heres another 1 if i swap the 79' engine and trany temporaily will it cause any issues with the drive line?

 

I think the solenoids are the same but you may want to search to be sure about the rats nest. Nothing wrong with the swap of the tranny and engine, but if I recall correctly you have to change the tail piece on the tranny because of the placement of the hole for the shifter on an SA.

 

i like being number 12
https://www.rx7club.com/1st-gen-general-discussion-207/sa-fb-owners-registry-655584/page15/
any ways im just gona have to rebuild the motor the rear rotor has NO compression i think it blew a seal i just hope the housing isnt screwd that would suck ... to many hoses and wires im gona need like 8 roles of masking tape, a felt- tip marker, me tools, jack-stands, jack, sumthing to kick when i get pissed..... besides my car, and i still have to re-assembly my interior aaaffffffter i sand blast the rear end and hit it with some rustolium, put in my new locks, put heat shielding back on, then put the motor back in all with out getting myslef/others hurt ..... ehhh, not gona happen... at least the getting hurt part

 

it is 5pm hear T is out sand blasting rust he found in side as I type he is also learning that walnut shells are not the greatest but its all we can get right now slow but he will get there once that is done we will use some rustolium then new insulation and paint on some bed liner after should seal her up nice anybody have any alturnative ideas

 

it starts all thanks to my girlfriend being here now it runs and i happy now

 

its not like it had anything to do with the third of a quart of castrol 20/50 I put into the rear rotor and let it sit for a couple days to free up the apex seals (was a last hope kinda thing and it payed off)

 

well i didnt know u did that so dont get grumpy

 

I'm not sure if you have the insulation already or not, but I used an adhesive sound deadening material (similar to dynamat). It's easy to work with and cuts down a lot of road noise and heat.
http://cgi.ebay.com/ebaymotors/100-F...em370033817510

 

shes up and running i just need an exhaust then i just get her licenced then i get to drive around

 

It's Father AND Son, father in son is a church related project.

 

nice corection, but as long as he aint tossing his kid between 2 chatholic preists and having them fight to the death its not that church related




lol

 

k back on topic if any1 knows where i can get a stock 12a exhaust or one that would work for a 12a. i dont want anything loud on the contrary i want sumthing quiet that will have suficent back presure

 

stock..might not find one for your 79..easier just to spend a lil money for the racing beat one.. its quiet and worth the money

 

k, well since i figured i wasnt gona be able to get a stock exhaust anyways i just need to find an afordable aftermarket exhaust

 

What part of the exhaust? Catback? Header?

 

from the thermal reactor to the muffler

 

Check out the parts for sale section and post a WTB for a muffler etc... and see what comes up.

You may want to go with a header, at some point anyways.

Racing Beat - brand new
Disassembled Road Race Header Kit
74-85 (12A)

Part Number: 16211
Retail Price: $115.00

For ideas on exhaust and what to get, take a look through the Racing Beat web site. They got the OD and wall thickness listed in their parts descriptions. That'll give you an idea of what to look for.

 

i got the muffler
just need everything between the two

 

a stock FB exhaust will work, right?
cause if so i might have an exhaust, then all i need is a clutch hose

 

I don't believe so, IIRC the SA has a 3rd pipe and the FB's don't. Plus I think the hangers are placed in different spots. You can check out Racing Beat's exhaust systems, even if you don't buy one from them you can at least see how they've got different part numbers for different year 1st gens, which would indicate that there are some sort of differences, otherwise they would only offer 1 part for all years.