RX7Club.com - Mazda RX7 Forum

RX7Club.com - Mazda RX7 Forum (https://www.rx7club.com/)
-   V-8 Powered RX-7's (https://www.rx7club.com/v-8-powered-rx-7s-299/)
-   -   LS1 to a T-5 Tranny (https://www.rx7club.com/v-8-powered-rx-7s-299/ls1-t-5-tranny-1047403/)

drama 09-27-13 07:42 AM

LS1 to a T-5 Tranny
 
Will a T-5 tranny bolt up and work correctly to a LS engine. I just don`t have the funds to buy a good T-56 right now. can always do it in a year or two.

boske 10-20-13 02:37 PM


Originally Posted by drama (Post 11583814)
Will a T-5 tranny bolt up and work correctly to a LS engine. I just don`t have the funds to buy a good T-56 right now. can always do it in a year or two.

First off there was never a T5 that bolted to an LS style block. With the t56 there are different years and bellhousing can be swapped between them but the t5 was only used on SBCs well before the LS came out. If there are adapters available I'm sure they will break your budget.

Gilgamesh 10-22-13 08:06 AM

they will bolt in with adapters.

quicktime i belive sells SFI rated swap bellhousings.

DarkDrakeX 11-07-13 12:04 AM

I literally just bolted a t5 to my ls. 99 chevy blazer 2wd manual transmission. Have to get a truck 10 spline clutch (4.8l silverado clutch). The 4.8l manual is a nv4500

Look at my last post.
https://www.rx7club.com/build-thread.../#post11616079

peachs 11-07-13 12:08 AM

Any transmission that will bolt to an old small-block chevy will physically bolt to any LSx engine minus one bolt that does not line up. You just need to find the correct flexplate/flywheel setup to make the transmission work...

roxy7lover 02-03-14 12:10 PM

Can I drop a chevy 350 with a t5 into a 2nd gen?

atli126 02-03-14 03:27 PM

I just went thru all this with my rx7 ls build, you can check it out here. also check out a no hate zone at norotors.com

sbc to ls1 fc rx7 - 502StreetScene

http://www.howeracing.com/p-7754-imp...ck-clutch.aspx

LS series T5 installation parts list:

Chevy world class t5 from a Camaro (90)
Bellhousing casting number 3899621
Stock LS1 or LS6 flywheel, pressure plate and clutch
Pilot bearing GM part #12557583
Howe racing hydraulic throwout bearing #82870
2 short hard lines to get you out the bellhousing.
3/4" or 7/8" master cylinder
fork (pioneer PN# CF100, GM 340278 & 14066235)


but seriously save your money and get a t56 and ls7 clutch and be happy, never worry about blowing the weakass t5 and be happy (ask me how i know)

gadzooks 02-07-14 08:39 PM


Originally Posted by roxy7lover (Post 11672307)
Can I drop a chevy 350 with a t5 into a 2nd gen?

with a Granny's Speed Shop kit, pretty much

ncaudio 02-08-14 12:01 PM

It'll work (from what others say), but don't beat on it, the T5 isn't super strong and you can tear it up.

vwnomore 03-30-14 06:16 PM

V8 roadsters sells a bellhousing for this. They were trying to get a series going for Miatas with L33's mated to t5s.

V8R Spec LSx T5 Bellhousing

valley 04-03-14 09:47 PM


Originally Posted by gadzooks (Post 11675407)
with a Granny's Speed Shop kit, pretty much

Never buy from Granny's. Search norotor's or just around if you'd like to know why.


All times are GMT -5. The time now is 05:24 PM.


© 2024 MH Sub I, LLC dba Internet Brands