RX7Club.com - Mazda RX7 Forum

RX7Club.com - Mazda RX7 Forum (https://www.rx7club.com/)
-   V-8 Powered RX-7's (https://www.rx7club.com/v-8-powered-rx-7s-299/)
-   -   Another LS-1 FD is born! (https://www.rx7club.com/v-8-powered-rx-7s-299/another-ls-1-fd-born-372643/)

LS1RX7 11-29-04 03:29 PM

Another LS-1 FD is born!
 
It is about a few weeks from being done, just some wiring and driveshaft stuff

It went together pretty nice, the Hinsons stuff fit really good, I only had to grind a few holes bigger, and the headers fit very nice. although one tube is pretty close to the steering shaft.

the FAST manifold fit after I cut away a bit of the firewall and welded it back up,
but you have to love that 90mm throttle body!!! (which I don't think will clear the hood)

I can't wait to drive it!

check out the pictures!!!!!

http://www.msrecycling.com/94_fd_rx7.htm

talljosh85 11-29-04 05:15 PM

well, good luck with it, as impure and bastardized as it may be. At least you'll never worry about your apex seals, water seals, or that damned fifth gear synchro. Maybe I'll see it sometime, being in Sactown and all. Josh

turbogarrett 11-29-04 06:16 PM

Nice! That car should put down some big #'s.

Crash Test Joey 11-29-04 06:27 PM


Originally Posted by talljosh85
well, good luck with it, as impure and bastardized as it may be. At least you'll never worry about your apex seals, water seals, or that damned fifth gear synchro. Maybe I'll see it sometime, being in Sactown and all. Josh

Damn, I think that was almost a compliment :D

Looks good. My FD/LS1 project is also in progress right now :bigthumb:

jimlab 11-29-04 08:22 PM

Have any bigger/better pictures of that bitchin' rear end setup? :)

owen is fat 11-30-04 01:34 PM

awesome project. good to see some pics too.

best of luck to ya, that should really rip with that much power... I am wondering if you should look into much wider tires at least out bck to put the power down.... like some 17x10's with 315 wide rubber would be "more" appropriate... and a little taller sidewall than 18" tires so you get a slightly better launch.

speedx7 11-30-04 03:19 PM

car looks good

LS1RX7 12-01-04 07:22 PM

Wheels
 
Yea the bigger 18x9.5 and 18X10" CCW's are on there way!

Hey Jim, I will Post up some of those pics in a day or so,
Thanks

LS1RX7 12-06-04 06:53 PM

Yea the hood does not fit , I cut away part of the hood reinforcement and it still needs a 1/4 of an inch to clear, it will shut but the top of the throttle body touches,

on thing I was noticing on the LSX intake is that it angles the TB up about 6 or 7 degrees, If I made a wedge type spacer to bring it back down the hood will clear.
.............time to break out the plasma cutter!!

AMallick 12-06-04 08:27 PM

Damn man, first an awd 4g63 mirage and now this. whats next?:)

88t2romad 12-06-04 09:24 PM

i hate you, but ill be content as long as you dont wreck it, have fun with it :)

digitalsolo 12-06-04 10:54 PM


Originally Posted by AMallick
Damn man, first an awd 4g63 mirage and now this. whats next?:)

The white one that was in SCC a few months back? Big power, little brakes?

LS1RX7 12-07-04 01:25 PM


Originally Posted by digitalsolo
The white one that was in SCC a few months back? Big power, little brakes?


Yea but that one was not AWD it was a typo, and yea it did dyno at over 500hp at the front wheels, on stock brakes!! yikes!!!!!!

I am the FIRST person in the U.S. to have done that to a c50 Mirage

I will not drive this car at any drift events where the line is very close to any walls, i.e. Irwindale, Altamont, Vegas Motorspeedway, that's what my 240 is for,
I am going to take the RX-7 to Thunder hill on January 15th for a Drift/Grip practice if any one in the area want's to go for a ride. you have to bring your own diapers though.....HEHE.
remember in drifting its not "If" you are going to wreck it's WHEN!!!!

jimlab 12-07-04 01:42 PM

Pictures? :D

2hotrods 01-21-05 05:47 PM

Where did you get the headers and how much did they cost? My car supposedly has "Stage II heads and Cam" but is still breathing through the stock LS1 manifolds. So there is some power hiding in there waiting to be brought out. Long Tube Headers are definitely on my near term wish list....

RX7WEEE 01-22-05 12:09 AM

Sigh.

BklynRX7 01-22-05 02:47 AM

I never understood the whole concept of calling a car with a swapped engine by the body. For example a corvette engine in a rx7 body is not an rx7 it is a disguised corvette. SO shouldnt things like this be on another site under " other body swaps".

jimlab 01-22-05 03:41 AM


Originally Posted by I EAT CIVICS
I never understood the whole concept of calling a car with a swapped engine by the body.

So the identity of the car is determined by the engine under the hood? Interesting concept. Not a new concept, certainly, but interesting just the same.


For example a corvette engine in a rx7 body is not an rx7 it is a disguised corvette.
Well, the last time I checked, even converted RX-7s still had most of their parts in common with the manufacturer of the body of the car, not the manufacturer of the engine. In other words, you'd still have to go to a Mazda parts dealer to replace the majority of the parts on the car, so how do you figure it's a disguised Corvette?

BTW, that's a nice way of saying that you're a blithering idiot. :p:

jimlab 01-22-05 03:42 AM


Originally Posted by RX7WEEE
Sigh.

Did you stumble into the wrong forum, or did you simply spring a leak?

Crash Test Joey 01-22-05 10:02 AM


Originally Posted by jimlab
So the identity of the car is determined by the engine under the hood?

Sure it is. That's why a stock RX7 with it's blown engine is not really an RX7 anymore - it's disguised piece of shit. I mean, if the rotary is the entire car, what difference does the rest of it make, right?

wingsfan 01-22-05 10:35 AM


Originally Posted by I EAT CIVICS
I never understood the whole concept of calling a car with a swapped engine by the body. For example a corvette engine in a rx7 body is not an rx7 it is a disguised corvette. SO shouldnt things like this be on another site under " other body swaps".

Last I checked, I still had the same chassis I started with, so you can't really call it a body swap. :rolleyes:

Plus, the guy at the GM parts counter is going to be really confused when I explain to him that my car is just a Corvette in disguise.

Why don't you go stir some shit in another forum. It never ceases to amaze me that people wander into the Other Engine Conversions section to put their arogant piety on display for everyone to see. It's simple really. If you're not a fan of engine conversions then just stay out of this section and leave it to those that are.

We haven't done anything to defile your car by swapping out our drivetrains, so why the fuck should you care?

ebb 01-22-05 10:35 AM


Originally Posted by jimlab
Did you stumble into the wrong forum, or did you simply spring a leak?

Jim you know deep down they all want it, that is why they look in threads like this anyway.

jimlab 01-22-05 11:53 AM


Originally Posted by Crash Test Joey
Sure it is. That's why a stock RX7 with it's blown engine is not really an RX7 anymore - it's disguised piece of shit. I mean, if the rotary is the entire car, what difference does the rest of it make, right?

Good point. So since my FD doesn't even have an engine in it right now, it's not even really a car? :p:

That would explain a lot, because I keep bumping into this thing in my garage that's about 14 feet long and about 6 feet wide, and I have no idea what it is...

jimlab 01-22-05 12:00 PM


Originally Posted by wingsfan
It never ceases to amaze me that people wander into the Other Engine Conversions section to put their arogant piety on display for everyone to see.

The funniest ones are the shit-talkers who you just know felt like they were delivering some deeply profound commentary on the subject of conversions, yet obviously didn't have the slightest clue how stupid they were making themselves look in the process. :D

Crash Test Joey 01-22-05 12:24 PM


Originally Posted by jimlab
Good point. So since my FD doesn't even have an engine in it right now, it's not even really a car? :p:

That would explain a lot, because I keep bumping into this thing in my garage that's about 14 feet long and about 6 feet wide, and I have no idea what it is...

If you ask some of these Mensa candidates, it would be considered a crime scene.

RX7WEEE 01-22-05 10:04 PM


Originally Posted by jimlab
Did you stumble into the wrong forum, or did you simply spring a leak?


lol your flameing me for saying Sigh....

jimlab 01-23-05 12:37 AM


Originally Posted by RX7WEEE
lol your flameing me for saying Sigh....

No, I'm flaming (note correct spelling) you for being an ignorant teenager. What you posted is immaterial.

backtrail69 01-23-05 10:41 PM

Jimlab your dumb.

jimlab 01-23-05 11:52 PM


Originally Posted by backtrail69
Jimlab your dumb.

Well, I don't have the great fortune to live in the academic Mecca of Anacortes like you do, so I haven't yet learned how to do without the contraction "you're" and simply use "your" instead... :p:

5 whole posts and you chose to spend one of them on trying to chastise me? Thank you, I am well and truly blessed.

d0 Luck 01-24-05 12:01 AM

jim, i think that dude's just made a diff. sn to produce that insult.

jimlab 01-24-05 12:10 AM


Originally Posted by d0 Luck
jim, i think that dude's just made a diff. sn to produce that insult.

What gave it away? This post? :D

https://www.rx7club.com/showpost.php...7&postcount=12

RX7WEEE 01-24-05 12:13 AM

Me? LOL...

How am I an ignorant teenager?

All i said was Sigh. my personal oppion is that your taking part of the car away when you do that swap. but that my oppion. i never said that i was a bad swap.

It is better in all ways, but like i said I feel that it takes away from the car.

he did a good job and im sure it hauls ass. so a :bigthumb: to him.

jimlab 01-24-05 12:21 AM


Originally Posted by RX7WEEE
How am I an ignorant teenager?


my personal oppion is that your taking part of the car away when you do that swap.
I rest my case.

RX7WEEE 01-24-05 12:39 AM

:wtf1: Since I think that it takes part of the car away I'm ignorant? I think that it needs to be a rotary, but thats my oppion.

If i was ignorant i would have said thats its a stupid thing to do, but did I NO.

So since I'm soo "Ignorant"

How many hours till I can be CFI, and what other rating are needed?

jimlab 01-24-05 12:49 AM


Originally Posted by RX7WEEE
I'm ignorant? I think that it needs to be a rotary, but thats my oppion.

You're ignorant because you can't spell "opinion" correctly.


If i was ignorant i would have said thats its a stupid thing to do, but did I NO.
Doesn't matter, you shouldn't have posted at all.

blackkiller7 01-24-05 12:57 AM


Originally Posted by jimlab
You're ignorant because you can't spell "opinion" correctly.

Doesn't matter, you shouldn't have posted at all.


LOL :) Now thats funny I don't care who you are!

RX7WEEE 01-24-05 12:58 AM

Sorry im dyslexic and cant spell for shit. But im sure that your perfect in every way :)

you never answer'd my question, but i dont care.

I just hope you dont act like this in person. Cya later and have a good day. :bigthumb:

jimlab 01-24-05 01:38 AM


Originally Posted by RX7WEEE
Sorry im dyslexic and cant spell for shit. But im sure that your perfect in every way :)

So they tell me.


Cya later and have a good day. :bigthumb:
No problem. Hope you can find your way out of the Other Engine Conversions forum and remember not to come back unless your "oppion" changes.

Evil Aviator 01-24-05 02:33 AM

Administrative action will be taken against those who don't have anything better to do than come to this forum to bash people because of their beliefs. Warnings have been issued to those deserved them. Please restrict yourself to the Lounge if you do not have the maturity to participate in the technical forums.


All times are GMT -5. The time now is 09:32 AM.


© 2024 MH Sub I, LLC dba Internet Brands