Picked up my 2jz motor for it
|
2jz ge/gte? with what transmission?
|
Originally Posted by 88AMG
(Post 11445657)
Picked up my 2jz motor for it
I guess rx7club & supra forums merged like Taco Bell and KFC!? Whatever it takes to get your post count up?! |
Originally Posted by cr7684
(Post 11446934)
Really???
I guess rx7club & supra forums merged like Taco Bell and KFC!? Whatever it takes to get your post count up?! Where's joe when you need to him to greet the out of towners. Just like Rambo I |
Yes really, and its a fc not a FD.
|
^^ don't get sensitive about it, i understand the other members, i am against swapping the rotary for a piston, but if youre dead set on doing it, a 2jz is a bad ass engine, i am myself dropping one on a 71 240z.
|
^^^ :scratch::scratch::scratch:
|
Took off some more of that tar stuff left over from the insulation. Should be completely done by this weekend.
|
2 Attachment(s)
Just finish checking my new turbo manifold and turbo for fitment.
Elliot @ Turblown makes an awesome manifold. |
I too, am contemplating a 2jzgte in my fc... for the reliability factor.
|
Reliability factor??????
|
Originally Posted by jm93rx7
(Post 11448059)
Reliability factor??????
|
Originally Posted by CHAVEZRAC1NG
(Post 11445643)
Drive it!
|
Originally Posted by 88AMG
(Post 11445657)
Picked up my 2jz motor for it
|
Originally Posted by sleepers4life
(Post 11448041)
I too, am contemplating a 2jzgte in my fc... for the reliability factor.
Just a bit of knowledge for you...... Reliabilty on ANY motor is ALL dependant on who builds it and who tunes it..... It has NOTHING to do with the type of motor.... There....you just learned something NEW for today....:balls: |
Originally Posted by bigpaparotor
(Post 11448007)
Just finish checking my new turbo manifold and turbo for fitment.
Elliot @ Turblown makes an awesome manifold. Where's the radiator??? got pics from the mouth viewing in? |
Originally Posted by NoPis10
(Post 11448225)
And here is winner #3...... Spoken like a TRUE dip shit...... You sir are NOT a Rotary fan..... Just stay on that band wagon you jumped on and get the @*%$ out of the SE section.....
Just a bit of knowledge for you...... Reliabilty on ANY motor is ALL dependant on who builds it and who tunes it..... It has NOTHING to do with the type of motor.... There....you just learned something NEW for today....:balls: :scratch: OOOOOOKKKKKKKKKK! :icon_tup: and no shit dipshit. i did say contemplating. BY THE WAY :blush:! s4 - s5 swapped fc project. however i dont deny the 2jz its fame because, it is among one of the most reliable when fully built an boosting hard! YOU JUST LEARNED.... something new today. :egrin: |
ok ok no reason to be rude here, i will post pics of my project up very soon. i have an 87 tII i have 2 blown s4 engines and just got ready to pull 1 out and swap with an s5. i threw around the idea of a 2jz for the fact the bottom end will hold up to like 800HP for 50 - 100000 miles in alot of cases. And, that alot of race events wont let a rotary compete with piston engines. AND the fact that a 13b with say 5 - 600 hp is only a low 14 - 18000 mile engine... especially in the case of competative racing! i love the rotary dont get me wrong, its small easy to work on and capable of big numbers. i love it. but the 2jz is no joke man!and thus i explain myself:dunno:
i also threw around the idea of a 1jz, 302, ls1, rb25, f20, and even a ka24.... why? because i have the time and i just simply can! but i landed on a 13b s5 or a 20b. and chose the not as costly, 13b s5. |
Originally Posted by snapcaseacilec
(Post 11448299)
Where's the radiator???
got pics from the mouth viewing in? Its under the Inter cooler. Its the rx7 store v mount kit. Ill see if i can post pics later today. |
Warmed it up and shut it down.
|
Drove the FD to Downtown and then to Beach Place for some dinner with my Lil Bro and his Ladies....
The wife really gets a kick when it hits boost....she says it feels like she's on a roller coaster ride.....Gotta love it when my 2 leading Ladies get along.. AHAHAHAHAHAHA |
Originally Posted by sleepers4life
(Post 11451805)
ok ok no reason to be rude here, i will post pics of my project up very soon. i have an 87 tII i have 2 blown s4 engines and just got ready to pull 1 out and swap with an s5. i threw around the idea of a 2jz for the fact the bottom end will hold up to like 800HP for 50 - 100000 miles in alot of cases. And, that alot of race events wont let a rotary compete with piston engines. AND the fact that a 13b with say 5 - 600 hp is only a low 14 - 18000 mile engine... especially in the case of competative racing! i love the rotary dont get me wrong, its small easy to work on and capable of big numbers. i love it. but the 2jz is no joke man!and thus i explain myself:dunno:
i also threw around the idea of a 1jz, 302, ls1, rb25, f20, and even a ka24.... why? because i have the time and i just simply can! but i landed on a 13b s5 or a 20b. and chose the not as costly, 13b s5.
Originally Posted by sleepers4life
(Post 11451805)
ok ok no reason to be rude here, i will post pics of my project up very soon. i have an 87 tII i have 2 blown s4 engines and just got ready to pull 1 out and swap with an s5. i threw around the idea of a 2jz for the fact the bottom end will hold up to like 800HP for 50 - 100000 miles in alot of cases. And, that alot of race events wont let a rotary compete with piston engines. AND the fact that a 13b with say 5 - 600 hp is only a low 14 - 18000 mile engine... especially in the case of competative racing! i love the rotary dont get me wrong, its small easy to work on and capable of big numbers. i love it. but the 2jz is no joke man!and thus i explain myself:dunno:
i also threw around the idea of a 1jz, 302, ls1, rb25, f20, and even a ka24.... why? because i have the time and i just simply can! but i landed on a 13b s5 or a 20b. and chose the not as costly, 13b s5. A rotary engine will last more then 18,000 miles, if it's build well & no cutting corners. Most who claim other wise really don't know the engine very well & blame it on the engine but the truth is you Failed. In the end we have to be responsible for what we know and don't know and learn from it point blank. Every engine has it's soft points & the 1jz & 2jz are known for their bearing issues, because of their torque they mushroom bearings at high RPM. My point is swapping out one issue for another is not fixing the problem nor are you learning what went wrong for the engine to fail, just my .02 either way good luck just out of respect for us don't post pics of your piston swap thank you Chris. |
Originally Posted by cr7684
(Post 11452664)
A rotary engine will last more then 18,000 miles, if it's build well & no cutting corners. Most who claim other wise really don't know the engine very well & blame it on the engine but the truth is you Failed. In the end we have to be responsible for what we know and don't know and learn from it point blank. Every engine has it's soft points & the 1jz & 2jz are known for their bearing issues, because of their torque they mushroom bearings at high RPM. My point is swapping out one issue for another is not fixing the problem nor are you learning what went wrong for the engine to fail, just my .02 either way good luck just out of respect for us don't post pics of your piston swap thank you Chris.
|
Went for two hour drive with 3 other FD's..........man did I have fun!
|
Originally Posted by papsmagu
(Post 11452820)
Went for two hour drive with 3 other FD's..........man did I have fun!
|
Very NICE ride!!! Can you send me the video you took Lu.
|
Here's a pic from my Downtown excursion last week..... Yes, I parked her on the street at a meter....
http://i293.photobucket.com/albums/m...psb25e31de.jpg |
Originally Posted by sleepers4life
(Post 11451805)
ok ok no reason to be rude here, i will post pics of my project up very soon. i have an 87 tII i have 2 blown s4 engines and just got ready to pull 1 out and swap with an s5. i threw around the idea of a 2jz for the fact the bottom end will hold up to like 800HP for 50 - 100000 miles in alot of cases. And, that alot of race events wont let a rotary compete with piston engines. AND the fact that a 13b with say 5 - 600 hp is only a low 14 - 18000 mile engine... especially in the case of competative racing! i love the rotary dont get me wrong, its small easy to work on and capable of big numbers. i love it. but the 2jz is no joke man!and thus i explain myself:dunno:
i also threw around the idea of a 1jz, 302, ls1, rb25, f20, and even a ka24.... why? because i have the time and i just simply can! but i landed on a 13b s5 or a 20b. and chose the not as costly, 13b s5. |
Joe that's a horrible pic of your bitch.....she is sexy but that pic makes her look bad! U gotta do better than that!
|
Sleepers4 life.
The 2jz trans gear is all wrong. The only engine/trans other than a rotary that will work is the ls1. It has a .5OD gear compared to the 2jz .8OD gear The guy who taught me to tune blow through is from Puerto Rico. His rotarys will make more HP for less money and last longer than any piston engine. |
Originally Posted by papsmagu
(Post 11458127)
Joe that's a horrible pic of your bitch.....she is sexy but that pic makes her look bad! U gotta do better than that!
|
Originally Posted by papsmagu
(Post 11458127)
Joe that's a horrible pic of your bitch.....she is sexy but that pic makes her look bad! U gotta do better than that!
http://i86.photobucket.com/albums/k8...an/null-33.jpg . |
Originally Posted by estevan62274
(Post 11458147)
^^^ Joe must of took that pic with his cell phone :D
http://i86.photobucket.com/albums/k8...an/null-33.jpg . |
Originally Posted by ghost1000
(Post 11458139)
Sleepers4 life.
The 2jz trans gear is all wrong. The only engine/trans other than a rotary that will work is the ls1. It has a .5OD gear compared to the 2jz .8OD gear The guy who taught me to tune blow through is from Puerto Rico. His rotarys will make more HP for less money and last longer than any piston engine. |
Rolled and pull rear fender. Change spark plugs. Picked up racing beat front sway bar bracket.
Fitted CF side difuser. |
Polish, Polish, Polish! Summer's coming time to get it out of the barn!:nod:
|
Originally Posted by Trish Anderson
(Post 11458928)
Polish, Polish, Polish! Summer's coming time to get it out of the barn!:nod:
Go get you post count up over there and STOP wasting our space with your Barn ride..... |
1 Attachment(s)
Washed it and took it for a short ride.
|
|
|
Spent more money on her.
|
Took mine out the FD for a long drive to adjust fuel map! Car feels great..
|
Originally Posted by FC3S1991
(Post 11460849)
Spent more money on her.
|
Originally Posted by bigpaparotor
(Post 11448007)
Just finish checking my new turbo manifold and turbo for fitment.
Elliot @ Turblown makes an awesome manifold. |
2 Attachment(s)
|
3 Attachment(s)
Laz glad your finally giving her some attention.
i started to breakdown my old motor.......after 10 years of abuse this thing is clean!!!!! Attachment 670547 Attachment 670547 Attachment 670549 |
3 Attachment(s)
swapped front bumper, lights, cleaned some wires, replaced exhaust, installed the driver side mirror. now i need to install coilovers, wheels, FMIC and other misc parts and get her painted!
so from this Attachment 670491 to this Attachment 670492 oh and drove my FB around, is great to be back home! The IMSA is next! Attachment 670493 |
Which 99 bumper is that..... Love the plateless look....
|
Originally Posted by che'srx-7
(Post 11484469)
swapped front bumper, lights, cleaned some wires, replaced exhaust, installed the driver side mirror. now i need to install coilovers, wheels, FMIC and other misc parts and get her painted!
so from this http://i250.photobucket.com/albums/g...ps50661a8b.jpg to this http://i250.photobucket.com/albums/g...ps59ea0e53.jpg oh and drove my FB around, is great to be back home! The IMSA is next! http://i250.photobucket.com/albums/g...ps138b2605.jpg |
^^^^^^^ clean looking FB
|
All times are GMT -5. The time now is 11:07 AM. |
© 2024 MH Sub I, LLC dba Internet Brands