1989 1jz Gte Powered Fc Rx7 !!
 

PLEASE CHECK OUT MY CARDOMAIN PAGE AND TELL ME WHAT YOU THINK ON THIS THREAD ALSO ANY BODY WITH A 1J IN THERE FC RX7 POST HERE AS WELL HOPE TO SEE SOME FLICKS SOON HERE ARE SOME TEASERS OVER 100 PICUTERS ON MY CARDOMAIN PLEASE RATE MY CAR ! THANKS ALOT !
MY CAR DOMAIN PAGE IS http://www.cardomain.com/ride/2919369

http://i13.photobucket.com/albums/a2...Picture001.jpg
http://i13.photobucket.com/albums/a2...Picture003.jpg
http://i13.photobucket.com/albums/a2...Picture004.jpg
http://i13.photobucket.com/albums/a2...Picture011.jpg
http://i13.photobucket.com/albums/a2...Picture069.jpg
http://i13.photobucket.com/albums/a2...9_177_full.jpg
http://i13.photobucket.com/albums/a2...Picture009.jpg
http://i13.photobucket.com/albums/a2...Picture008.jpg
http://i13.photobucket.com/albums/a2...a6942/1324.jpg

Looks clean! How's it handle/drive?

Nice car man. The shaved mouldings is so odd but okay to see once in a while. Without mouldings in my opinion, it looks like half the car is gone.

That car would be Nicer with a Rotary in there..lol. Does the car run?

...special...

not my cup of tea ...........but well done, props to you.

+1

wow very clean and one-of-a-kind

is that a ca18 out of a 240sx?

I haven't done any work to my car for about 6 months now. I finally got all the parts that i needed to do my Drivetrain Swap from a non turbo W58.. to a R154 turbo tranny. Here is the setup that I've put together. 88 turboII lsd rear-end ( Clutch Type ) The 91 Viscous is making some funny noises so its time to change things up. Custom Drive Shaft by Broward Powertrain. Mounts will be modified from the W58 carriage mounts. OS Giken Twin Disc Clutch Kit. Part # TS2BD. Push to Pull Conversion for the OS Giken Twin Disc. With this setup i should be able to tune my car up to at least 450 hp @ about 13lbs of boost.. Safely!! Keyword "Safely"....

04/26/09 - Took out the W58 non-turbo transmission.. Took off existing 4 puck ACT Clutch & Pressure Plate.
Ok these are the pictures of the Old Flywheel, Pressure Plate, Clutch Disc, Shifter & Transmission.
http://i13.photobucket.com/albums/a2...2/DSC03347.jpg
http://i13.photobucket.com/albums/a2...2/DSC03348.jpg
http://i13.photobucket.com/albums/a2...2/DSC03360.jpg
http://i13.photobucket.com/albums/a2...2/DSC03359.jpg
http://i13.photobucket.com/albums/a2...2/DSC03358.jpg
Here are some pictures of the Install of the OS Giken Twin Disc.. Its looks so shinny....
http://i13.photobucket.com/albums/a2...2/DSC03364.jpg
http://i13.photobucket.com/albums/a2...2/DSC03357.jpg
http://i13.photobucket.com/albums/a2...2/DSC03363.jpg
http://i13.photobucket.com/albums/a2...2/DSC03362.jpg
No oil leaks...
http://i13.photobucket.com/albums/a2...2/DSC03351.jpg
I cant wait to hit the road... Its time to make some money....

04/29/09 - Alright .. I got my R154 Tranny today. ( Thanks TurboII Rudeboy ). I installed my Push to Pull Conversion for the OS Twin Disc Setup, also put my bellhousing on the tranny.. Tommorrow it is time to bang out the Transmission Tunnel to make clearance for the bigger tranny. I will be uploading pictures tommorow night of my days work.. Stay tuned..

I have a few questions for you!

1. Did you fab your own motor and trans mounts?

2. What transmission were you using prior to the r154.

3. Are you using late model supra bellhousing with it or the r154 housing?

4. Tech2 shifter extention work for the r154?

5. Tech2 conversion driveshaft work for r154 as well?