400+ hp Microtech Club - Whos In It?
I'd like to think I'm Initiating my way In there as I'm waiting for everything to tie In together...slowly, but surely.
Who's In It? What Microtech are you running and details of your setup would be great. Let's hear of the 400+ hp Microtech RX-7's. |
Not many, eh? :(
|
I switched to an E6X.
|
Hey me but I live in Thailand.got hp around 450 rwhp
|
Sounds Interesting kong13B. Can you give us details/pics?
|
410 RWHP 311 TQ at 16 psi with T66 (See Sig)
http://www.alantripp.com/410DYNO.jpg |
Originally posted by pianoprodigy 410 RWHP 311 TQ at 16 psi with T66 (See Sig) http://www.alantripp.com/410DYNO.jpg WOW how well does the engine perform in the 12's for your A/F ratio? Any major signs of knock? I've never seen an A/F curve that flat and level in the 12 range:eek: |
i made 463 rwhp at summernats,
setup is LTX12 t66 2x550 and 4x1200cc injectors s4 turbo block s4 turbo box 9in diff, Pump fuel tuned by Jon (rxeng), myself and project-x new setup is LTX12s gt42 2x800cc and 4x1600cc injectors bridge port (rxeng) ford toploader with liberty dog gears 9in diif looking to make 620+rwhp and low 9sec 1/4 mile Dale |
i was there with the old setup on E6K but im switchin to Microtech after this last engine blew..
T66ish size turbo 4x720cc (should put me right around at the 400mark) S5 block Mild port walboro S5 box |
I'm applying for membership, new streetported engine, ported twins, downpipe w/high flow exaust, LT12 Microtech, custom v-mount, and Apexi intakes. Rx6b turbo later. All this on an automatic FD.
Matt |
You know you never have to pay...:D...just dyno sheets Is a prerequisite.
|
For you few with 400+ HP, how is driveability?
|
Originally posted by t-von WOW how well does the engine perform in the 12's for your A/F ratio? Any major signs of knock? I've never seen an A/F curve that flat and level in the 12 range:eek: |
I'm planning on getting there. I'm not sure how much boost I'd have to run on my little 60-1. I am about to put in my 1600cc injectors, fuel pressure regulator, and put my 850s as primaries. I'm on stock ports too.
|
I prefer Haltech after hacing tuned and installed a Lt8 however here's a dyno chart from my friends T2.
T70 Street port S4 block Greddy 32r fmic Microtec lt8 720/1680cc etc http://www.idahorotary.com/dyno448.jpg 110 advanced timing 19 psi dropping to around 16 and toooooo much fuel.. J |
I made 480 rwhp
Set up is: 12a turbo block (bridgeport) LTX8 13bt inlet and throttle body 2 x 800cc and 2 x 1700cc injectors s4 gearbox Hilux diff I have a dyno sheet but need someone to host it. |
I don't want to post under somone that made 480 but..
I made 300 at 12 psi....ran out of fuel = ( LT8 street ported S5 TII T04B 2- 720's 2-860's and all the other junk. I'm dropping in a pair of 1600's right now and going to try and squeeze 390-400 out of the to4b before I go 60-1 hi-fi. That should push it to about 18-20 psi before the t04b falls flate = ) Oh yeah, I drive the car every day. |
I've done at least 100 of them!!!!!!
Not all in RX7's but all are 12A or 13B engines (with a few 20B's in there too). I also have need a membership in the 500hp,600hp & 700hp at the wheels club too!!! All with Microtech!!!!!!!!!!!! |
Originally posted by HIMNI Racing I don't want to post under somone that made 480 but.. I made 300 at 12 psi....ran out of fuel = ( LT8 street ported S5 TII T04B 2- 720's 2-860's and all the other junk. I'm dropping in a pair of 1600's right now and going to try and squeeze 390-400 out of the to4b before I go 60-1 hi-fi. That should push it to about 18-20 psi before the t04b falls flate = ) Oh yeah, I drive the car every day. Dan |
Originally posted by WestJaxVert How the heck did you run out of fuel? I was running a TO4E at around 12-13psi with 550's and 850's and had no problem. Dan I'm going back this SAT. so he can play with it more :) Oh, remember that a t04b will out-flow a t04e |
Originally posted by HIMNI Racing They were at about 73% (41 psi base press. with a RRFPR) and Rolo said any more isn't good. I always tought 80 was OK but who in there right mind would go against what Rolo suggests? After 25 years of tunning the MT and seeing him pull a extra 60 HP out of the engine, with almost not even looking at the hand controller.... Originally posted by HIMNI Racing I'm going back this SAT. so he can play with it more :) Originally posted by HIMNI Racing Oh, remember that a t04b will out-flow a t04e Dan |
T04B will not outflow a TO4E, a 60-1 wheel in a t04b housing will outflow a smaller T04E, and a 60-1 wheel in a t04e housing will flow even more....
|
I want to be in, just have to get the MT in this summer and pick a turbo. In all honesty it will probably be next year before its done.
|
i'll be there as soon as i get my GT40R. I'm running the LTX8S unit.
can't wait!! |
measly 320rwhp
I hit 318 at the wheels in my 89 S5, so i guess that's about 400 at the flywheel...see sig for specs. But my battery recently blew up and the moron who installed my lt8 didn't put in an inline fuse. So now i'm upgrading to an LTX12, hopefully that'll help a little and it'll give the option of upgrading a a 20B later :D
|
All times are GMT -5. The time now is 03:16 PM. |
© 2024 MH Sub I, LLC dba Internet Brands