i guess the throttle body is 750 cfm...

 

Longshot maybe...but do you have any F9 base maps?

9.7 rotors
6-port block
550/780 injectors
12 psi
3 bar map

 

Can someone seems me a good timing map?

E8, 850/1600s. T78
S6, mild Street port, Ls coils, PFS big smic, 3" hks high power.

I'm most interested in a good solid timing map. The fuel trims on my map are semi reasonable, but whoever tuned it last had no idea what they were doing...

 

Looking for base map for 2nd gen tii.
Mods:
Fmic
Walbro
550cc primaries
1680cc secondaries
Removed emissions
Stock turbo
Stock coils
Running ps1k thanks email is bmwguy330@gmail.com

 

i got installed and already run the engine with base map sent by my dealer here in my country
but the engine cant get start when the temperature get hot (arround 70-90'C)

anyone can send me the base map with correction for the normal engine temperature please...

FYI : im using patch loom for my car...

 

Check haltech website. They should have a basemap that woks

 

thanks bro...
but my prob is the fuel pump... just got found it lately...
my stupid ness sometimes forgot the basic things...
thanks

 

FC
13b
Turbonetics T04b turbo
Stock ignition
Dual walbro 255
Haltech on board map sensor
Stock tps
Haltech coolant temp and air temp sensors
RC 1200 primary low ohm
Bosch 1600 secondary low ohm
E85
Haltech platinum 1000
No bypass air control


If someone could help me out, I'd appreciate it. Thanks!

 

E6K
13b series 4, 6 port NA
medium/large street port, no aux sleeves (open 6 ports)
50mm ITB, DCOE style
AEM smart coils x4
4x 560cc low impedance injector (2 rpm based activation standoff/external injecotrs)

anything to get me started up and movable would be nice
thanks in advance

 

^^^ I could use this same base-map! do share?

 

I am looking for a base map for an Ek6

1. 6 port
2. Stock coils
3. Bridgeport
4. 500cc primaries, 1000cc secondaries
5. Electronic carb setup. RB lower intake
The engine is in a 82 corolla wagon.

We had a decent map going and the hard drive crashed and lost everything...didn't write anything down unfortunately.

Thank you

 

Not sure if this thread is ever checked any more, but figure its worth a shot.

Another request for NA maps. Don't seem to be too many floating around...

• Haltech F9
• S5 6-port
• large streetport
• S5 intake / injectors (460cc primary & secondary)
• Racing Beat collected header for FB
• Stock GSL-SE ignition

 

still looking for something for this...

the car is a 1985 GS...
it has 1987 13b for port.
I'm running a 4 barrel intake Jaytech brand..
autonomics 4 barrel throttle plate.. I believe it's around 6 to 700 cfm I'm not sure since they went out of business

I have ID 725 primaries and ID 2000 secondaries.. the fuel pump for now is an inline Walbro 255 lph I have 3/8 inch fuel lines feed and return have an aeromotive rising rate feul pressure regulator.. running 93 octane and premix...

I'm using an FC crank angle sensor. Greddy race plugs heat range 10 and 9. Four AEM smart oils.

I'm going to be running GM 3 bar map sensor GM intake air temp sensor GM coolant temp sensor. AEM wideband that I might tap into..

I have a Turblown stageV GT35r with true t4 housing wheel and flange.. custom Turblown short Runner exhaust manifold.. tile 44 millimeter waste gate 7.5 pound spring.. 3.5 inch downpipe and full straight through 3.5 in SS exhaust.. all 2.5 inch intercooler piping.. eBay front mount intercooler.. HKS SSQV blow off valve...

 

Now you're just bragging jk love it bro!!

 

May still be weeks away from start up, but will need a good base map to start out with.

Setup is:
PS1000
'93 FD
13B-rew pettit racing streetport
GM 3bar map sensor
750cc/2200cc injectors
Xcessive manufacturing LIM
stock UIM and throttle body
GM IAT sensor in Greddy elbow
OMP blocked off (premix in tank)
Aspec kit with PT6266 (vband inlet turbine)
expect to run about 20PSI boost
3" exhaust with High flow cat
4x IGN1A coils
MAC boost control solenoid
Pettit cool power intercooler kit.
Snow water/meth inj (want to tune to run with out it but use it for safety)

If there are any variables I left out let me know.

Thanks So Much in advance

Victor

 

actually there are two things I see I left off.

FFE trigger wheel (rx8 style) with Hall effect sensor

AEM wide band O2 sensor

 

no its just that no one seems to have anything for these ecus anymore...

 

Dont think anyone is here anymore but:

Need basemap for Sprint RE

13b-rew, stock ports
Gt35/40r
stock 850/ev1 1650
stock ignition
onboard map
12lbs boost
stock CAS

 

I am looking for ignition timing for a 20B running a P2000 and LS1 coils.

Thanks

 

S4 stock port
gt35r
Haltech PS1K
4xIGN-1A
FFE trigger wheel
All haltech sensors
Stock BAC
4x ID1000
walbro 255


Especially the FFE/ign-1a/id1000/haltech sensors combo seems to be tricky to find...

what u think abt 350rwhp with this setup after final tune btw? possible on pump gas?

 

looking for 550cc 850cc base map for a e6K if anyone has one

 

I'm running an e6k with 550/850 injectors. I have a map I modified after downloading from the Hitman years ago. I'm also using a t03/04 hybrid.

If this is similar to your setup then it may be a good starting point. Let me know if you still need a map.

 

makes me laugh that people ask for a Base map and then never has their car properly tuned

 

Merely an offer of assistance. My apologies if I offended. Base map is a prerequisite to a proper final tune; whether you pay someone or do it yourself.

 

I am new 2 haltech.I have always done microtech.Looking for a base map for a streetported rew motor,72mm turbo.880/1600 injector combo,ls1 coils and stock second gen cas.