Custom Solenoid Rack
To all forum members that might have slow responsive turbo spooling and bad solenoid valves etc, this may be beneficial to you
After saxyman built a custom rack which was widly spread within the community, and recreating this custom rack wasn't quite as easy. Benefit of this custom solenoid rack includes: 1)Eliminates stock solenoids which fails quick easily due to location 2)Relocate of new solenoids result in long lasting solenoid 3)These solenoids are rated at 100psi therefore it is great for aftermarket twins like BNRs if you wanted higher boost 4)A much more smooth spool transition from primary to secondary turbo. 5)Better reliability on the solenoid system which results a much more enjoyable twin turbo system 6)Responsiveness of solenoid reacts quicker than stock. Some might noticed a difference some might not. Therefore do NOT expect a "faster" response compared to stock solenoid system. However I believe it is "quicker". More information and pictures of the build can be found HERE This kit consist of: Item Quantity Solenoid Valve - TCP, CRV, CCA, TCV Manifold Connector 1/8 Barb x 10-32 10-32 plug with seal Fitting 32-001 Adjust elbow 1/8 X 10-32 MALE Viton check valves Y split plastic barb 1/8" vacuum caps bolt and nuts Mounting Bracket 1 Wires Blade Connectors Bullet Connectors - Male Bullet Connectors - Female Heat Shrink Butt connector Installation Guide in PDF form Vacuum diagram for correct routing of hoses Solenoid Specs: Viton seals Stainless Steel internals Molded coil (resistant to water and temperatures in excess of 300deg) Custom aluminum manifold 100psi rating Electroless Nickel Plated Brass fittings Better flow and reaction time than stock solenoids Rebuildable Shipping anywhere in the lower 48 (overseas customers: please contact me prior to purchase to get additional information on shipping) Group Buy close-out: We have 3 months till this GB closes. However if we can fill up the 10 spots on the list, I can start the run right away. IF WE ARE ABLE TO FILL 20 SPOTS ON THE LIST, 1 LUCKLY BUYER WILL BE ABLE TO RECEIVE HIS SOLENOID RACK FREE OF CHARGE!!!! Shipping time: Once I begin to place orders for parts, you can expect about 3-4 weeks before the finished system arrives at your door. IF ANYTHING WERE TO COME UP, I ASSURE EVERYONE THAT I WILL BE CONSISTENTLY IN CONTACT THROUGH EMAIL OR PMs. For this GB to work, I would require a non-refundable of $250 up front payment.(Why such a high non-refundable? Because once the order is sent through, there's no refund on my part and these solenoids are freakn expensive. However you will get JUST the solenoids itself if you've decided to back out) If pay by paypal, please USE THIS CALCULATOR to figure out the fee and the payment w/o shipping cost for now. As shipping is to be determined. Purchase instructions: Payment can be made via paypal to this address: x_aze04@yahoo.com I also accept personal checks, money orders or cash (if you decide to drop off the money and you are local) When you send payment, please be sure to include the following: Full name Forum User Name A good shipping address Phone number preferred, but OK without it. If you have any questions not specifically addressed in this thread, please do not hesitate to ask. Posting in this (or the other) thread, PMing, e-mailing, and calling me are all completely acceptable forms of contact. Thanks for your interest and support!!! Lets get this GB started!!! Eric Zheng Bridgeway Auto Repair Inc 1101 Bridgeway blvd. Sausalito CA 94965 (415)332-6622 or ezheng86@gmail.com |
Here is the list:
1. oyvindjs 2. RENESISFD 3. schleprx7 4. 5. |
i will be able to get in on this soon
|
Originally Posted by bolg033
(Post 10780549)
i will be able to get in on this soon
Guys, if you are serious about this, please add yourself on the list as this GB will be open until we hit 10 people. Therefore just add yourself on the list to be sure to save yourself a spot so we are ready, we can pull the trigger and get this going. Thanks in advance! Cheers, -AzEKnightz |
i see im on the list, good :) Im in!
|
1. oyvindjs
2. RENESISFD 3. schleprx7 4. twinsinside 5. I see the $250 deposit and shipping TBD but how much will the total cost be? thanks! |
Originally Posted by twinsinside
(Post 10781052)
1. oyvindjs
2. RENESISFD 3. schleprx7 4. twinsinside 5. I see the $250 deposit and shipping TBD but how much will the total cost be? thanks! Total cost is at $525 + shipping right now for 10 people. If we can get 15, it will be 500. And if we can get 20, there will be one lucky person with a free kit =]. -AzEKnightz |
Just FYI, for anyone planning to stay sequential, this may be the best money you ever spent. I have had the original kit for several years and am very happy with it. One of the greatest benefits is that you can test any vacuum circuit (relative to the turbos) without going under the manifold. just hook up test gauges and run them into the cockpit. Watch exactly when transition occurs (and when it reverts to primary). If you have a PFC/datalogit, you can adjust transition elements as well.
You have to be a "do-it-yourselfer" for all of this, but if you are still driving a 3rd gen and have twin sequential setup, you are a "do-it-yoursefer" by definition! Good luck! --Jeff |
I'm in.
1. oyvindjs 2. RENESISFD 3. schleprx7 4. twinsinside 5. wadejg Thanks, Justin Wade |
If I planned on running high boost on my black car I'd definitely jump in on this, looks like a pretty nice product.... Good luck with the gb :)
-Dan |
Originally Posted by Scrub
(Post 10787311)
If I planned on running high boost on my black car I'd definitely jump in on this, looks like a pretty nice product.... Good luck with the gb :)
-Dan -AzEKnightz |
Do you guys want to go ahead with this GB? If so, I will start product and accept payment once this is confirmed.
After this initial GB, I will probably bump up the price as my vendor just told me the price of the solenoids and fittings just went up 10%. I want to get this going. What ya'll think? -AzEKnightz |
^ Get it going:)! You have 5 people. I cant wait to have this in my car, I am so excited.
John |
Originally Posted by RENESISFD
(Post 10792470)
^ Get it going:)! You have 5 people. I cant wait to have this in my car, I am so excited.
John -AzEKnightz |
Is this something you plan to keep offering or a once/first few months only? My engine is done so while this is tempting I do have bigger priorities..
|
Lets do it.
Justin Wade |
Originally Posted by whiteweazel21
(Post 10792504)
Is this something you plan to keep offering or a once/first few months only? My engine is done so while this is tempting I do have bigger priorities..
1. oyvindjs 2. RENESISFD - Confirmed 3. schleprx7 - Confirmed 4. twinsinside 5. wadejg - Confirmed 2 more confirmations then we can get this rolling!!!! -AzEKnightz |
1. oyvindjs - confirmed
2. RENESISFD - Confirmed 3. schleprx7 - Confirmed 4. twinsinside 5. wadejg - Confirmed 1 more to go, and I shall contact my vendor for an accurate shipment time. This is getting along guys =). -AzEKnightz |
I'm in bro.
|
Originally Posted by twinsinside
(Post 10795379)
I'm in bro.
2. RENESISFD - Confirmed 3. schleprx7 - Confirmed 4. twinsinside - Confirmed 5. wadejg - Confirmed Great news, we've got all 5 spot filled and confirmed. I will contact my distributor to get a solid number on delivery date. Once I have that settled I will start requesting payments. Thank you for your patience. -AzEKnightz |
I will do this for sure. Just need to get my FD back from the shop to determine how much I owe him if its not much I can do it this paycheck otherwise I will next (2 weeks).
|
Originally Posted by Evopanda
(Post 10796437)
I will do this for sure. Just need to get my FD back from the shop to determine how much I owe him if its not much I can do it this paycheck otherwise I will next (2 weeks).
Here, let me start it for you =] 2nd GB list: 1. Evopanda 2. 3. 4. 5. -AzEKnightz |
Guys, I just received confirmation that once I place an order. I shall receive the shipments within 7-10 business days. That's approximately 2 week lead time. And it will take about once week for assembly and get ship out. I would suggest that you shall receive your custom rack in a time frame from 3-4 weeks MAX!
However, do expect the unexpected because sometime the distributor WILL make mistakes which I wont have the power to control. However I have confirmed that they have the parts we need in stock. Therefore you are ready to send in your payments. I take payments in forms of: Paypal E-check ($5 fee) Paypal credit card/services (Please send in $257.78 for the fee) Paypal Gift : under Send Money, there is a tab that you can select either "PURCHASE" or "PERSONAL" . Select "PERSONAL" and click on GIFT and continue. (You will waive the transaction fee if it is directly withdrawn from your account. Remember if you pay with a credit card, there will also be a fee.) Cashier's check Cash: If you are local If paying by payment, under Message section, please include: Your Forum User Name Your Full Name Complete shipping address Contact phone number and/or email Thank you for your support! My paypal is: x_aze04@yahoo.com -Eric Zheng |
Paypal sent
John |
Originally Posted by RENESISFD
(Post 10796626)
Paypal sent
John -Eric |
1. oyvindjs -
2. RENESISFD - Deposit Received 3. schleprx7 - Deposit Received 4. twinsinside - 5. wadejg - |
I'm really surprised more people haven't jumped on this. Have you posted this on other rotary forums too?
-Dan |
^Me too. I thought the demand would have been much greater :scratch:.
John |
Originally Posted by SBGarage
(Post 10797918)
I'm really surprised more people haven't jumped on this. Have you posted this on other rotary forums too?
-Dan
Originally Posted by RENESISFD
(Post 10797943)
^Me too. I thought the demand would have been much greater :scratch:.
John -Eric |
Originally Posted by AzEKnightz
(Post 10797946)
.
Me three john!!!! There were almost 20 people under the "interested list" only 5 came through. I guess prices affect the GB quite a bit. On top of that, I am sure the people who were interested compared the prices 6 years ago to now. Which "almost" doubling the prices. What can I say? -Eric -Dan |
^Lots of window shoppers now:(.
John |
Originally Posted by Scrub
(Post 10797953)
I'm sure you've noticed this, but the community is much different now then it was say five years ago. Anyone can put their name on a list, but when it comes time to pay they're nowhere to be seen.
-Dan
Originally Posted by RENESISFD
(Post 10797957)
^Lots of window shoppers now:(.
John -Eric |
I was mildly interested, but I'd rather keep the rack in the stock position. I'm not really open to dealing with a reticent emissions inspector.
|
Im interested! as I have the rack out since I'm doing a lot work there, if I order now what would be your eta? I can send full payment now if it makes a difference...
Also, how are these being connected to the harness, there seems to be some variation on the methods. I would like the easiest method and I don't really feel comfortable splicing the oem harness so a pnp would be ideal for me. |
2nd GB list:
1. Evopanda 2. ColdFeet 3. 4. 5. |
Deposit sent.
|
deposit sent, thanks.
|
Originally Posted by Sephek
(Post 10799007)
Im interested! as I have the rack out since I'm doing a lot work there, if I order now what would be your eta? I can send full payment now if it makes a difference...
Also, how are these being connected to the harness, there seems to be some variation on the methods. I would like the easiest method and I don't really feel comfortable splicing the oem harness so a pnp would be ideal for me. On the for the pnp, would you like a straight wiring connection from solenoid rack? or solenoid rack > 8 pin connector > to engine harness connectors? -Eric |
1. oyvindjs -
2. RENESISFD - Deposit Received 3. schleprx7 - Deposit Received 4. twinsinside - Deposit Received 5. wadejg - 6. ColdFeet - Deposit Received One more deposit then we can start this GB. Wadejg, and oyvindjs, please send in your deposit to secure yourself in the spot, otherwise I will start the GB once the 5th payment is received then you'll have to wait till the second GB. I will now send you both a PM to confirm this. Thanks! -Eric |
Originally Posted by BizarroTerl
(Post 10798457)
I was mildly interested, but I'd rather keep the rack in the stock position. I'm not really open to dealing with a reticent emissions inspector.
-Eric |
I know my brother is interested in this setup, but he's been spending his car fund on lots of other needed parts right now. I'll point him in this direction for ya :icon_tup:
|
Originally Posted by GoodfellaFD3S
(Post 10800252)
I know my brother is interested in this setup, but he's been spending his car fund on lots of other needed parts right now. I'll point him in this direction for ya :icon_tup:
-Eric |
Guys, I just wanted to clarify that after this initial GB. The price will go up 10% as my cost for the solenoids has gone up.
I believed I've stated in my build thread but has not mentioned it here on this GB thread. Therefore if you want to save some money, do it now rather than in the second GB and so forth. Since I've stated this price before the price changed, I will honor the current price ONLY until I fill up the 5th spot or receive my 5th payment.( I've already received my 4th payment last night) However I will still honor the same price if you can get me the payment in by the 28th. Basically what I am saying is I am not capping this first initial GB to 5 spots, but a minimum of 5 orders to get this going. So, if you really to jump onto this GB do it ASAP! -Eric |
Originally Posted by AzEKnightz
(Post 10800133)
If you can send in your payment (257.78 - paypal fee included, or 250 if send by gift) to x_aze04@yahoo.com then I can include you in the current GB. My ETA is approximately 3-4 weeks top!
On the for the pnp, would you like a straight wiring connection from solenoid rack? or solenoid rack > 8 pin connector > to engine harness connectors? -Eric Also, for the the pnp, the latter would work for me. When you say "straight wiring connection from the solenoid rack" do you mean just plain wires with no connectors at one end? |
Originally Posted by Sephek
(Post 10800621)
Deposit sent!
Also, for the the pnp, the latter would work for me. When you say "straight wiring connection from the solenoid rack" do you mean just plain wires with no connectors at one end? However I am currently trying to make a harness for one of the member at my cost for a "PnP" with one 8 pin connector so it can be easily disconnected behind the UIM rather than removing the UIM to get access to remove the wires for testing etc. 1. oyvindjs - 2. RENESISFD - Deposit Received 3. schleprx7 - Deposit Received 4. twinsinside - Deposit Received 5. wadejg - Deposit Received 6. ColdFeet - Deposit Received 7. Sephek - Deposit Received Looks like we are ready to lock-and-load. However, I would like to give oyvindjs a couple more days to respond to me as he is the first one to contact me regarding this GB and has been following the build thread since I started (And he is oversea), therefore please bear with me for a couple more days for him to respond so I wont have to put him on the second GB and have to raise a price on him. Again, I thank you all for the support and patience through this process and I will try my very best to get them out within 3 week time period. However it shouldnt take long than 4 weeks after I order all parts. Cheers! Eric Zheng |
hi folx, sorry for holding the GB up, ive been hospitalized the last few days. :(
Backproblems, musclecramps so intense that it pinched the nerves going to legs, so i lost touch/feel in em. Im up and walking again now, ill get on it when i get home, and fix the deposit. Thanks for the patience! :) |
Originally Posted by oyvindjs
(Post 10800954)
hi folx, sorry for holding the GB up, ive been hospitalized the last few days. :(
Backproblems, musclecramps so intense that it pinched the nerves going to legs, so i lost touch/feel in em. Im up and walking again now, ill get on it when i get home, and fix the deposit. Thanks for the patience! :) -Eric |
Originally Posted by AzEKnightz
(Post 10800832)
...
However I am currently trying to make a harness for one of the member at my cost for a "PnP" with one 8 pin connector so it can be easily disconnected behind the UIM rather than removing the UIM to get access to remove the wires for testing etc. ... |
Øyvind, you have sent $250.00 USD to Eric Zheng.
We have sent a payment receipt to your email and a notification to Eric Zheng at x_aze04@yahoo.com |
Originally Posted by oyvindjs
(Post 10802717)
Øyvind, you have sent $250.00 USD to Eric Zheng.
We have sent a payment receipt to your email and a notification to Eric Zheng at x_aze04@yahoo.com ***GB is now OFFICIALLY started for the first round*** I will place an order on all parts today and expect them to be here by next wednesday or the monday the week after. I will keep everyone updated every other day to make sure we are all on the same page. However, if any of u have any questions; do not hesitate to contact me. Thank you for all your supports and patience, now let's get everything going!!! Cheers, Eric Zheng |
All times are GMT -5. The time now is 05:47 AM. |
© 2024 MH Sub I, LLC dba Internet Brands