GB: 100% BRAND NEW JDM (V161) Supra Getrag Trannies!
This GB (which I anticipate to be small) is for 100% BRAND SPANKIN NEW JDM (V161) Supra Getrag Trannies, coming straight from Japan. I can get 'em for $6,000 a pop SHIPPED, provided I get 2 - 3 orders in (and obviously a larger discount if I can get a few more orders). The V161s are VERY hard to get used, and near impossible to find new. But hey, this is what I do best ;) These units will only be available for a short time, so jump in while you can, because I'll be placing the order VERY soon (before the end of the month).
Thanks! ~Ramy FDNewbie Imports |
Damn, I want one of these but I might not be able to jump in on it this month. The holidays are gonna kill my wallet. I'm probably not the only one either. :)
How many are needed for further price breaks and what would the price structure look like? Any chance of keeping the GB open till the end of January? |
Whats the point of this for the 6 spd? Direct bolton or does it require adapters?
|
This is for people who want a near bullet proof transmission that will be able to hold gobs of power without leaving bits and pieces of itself behind you when you take off.
I think there is going to be a separate GB for the adapters and clutch setups.. |
why not t56 ?
|
wtfx100, as Juiceh mentioned, there are many pros to this. And this thread is NOT meant for discussion (sorry sub9lulu). But this topic has been discussed to death on several threads. For all those who'd like to do more reading or ask questions about the setup, please refer to this thread: https://www.rx7club.com/20b-forum-95/tranny-618433/.
And yes, as Juiceh mentioned, a separate GB will be setup shortly for the full bolt-on adapter kit. As for price break, there really isn't much of one. At most, we'd be looking at $250 or so off the price if I got a good number of ppl in (5 or more). And that's assuming the exchange rate holds still (these are obviously available directly from Japan ONLY). If the exchange rate changes, the price will change accordingly. Re: time...tough to say. I suppose anything's possible, but honestly I would not be inclined to wait that long (2 months) unless I had 2 - 3 ppl w/ a substantial deposit in place to ensure follow-through (say $500 or so), because these are made in a limited quantity, and as such, time is of the essence. Plus, I've noticed that the price has been increasing steadily over the past few months to reflect this. ~Ramy |
I'm sorry if it's been spelled out elsewhere, but what are the advantages to the V161 over the V160?
|
https://www.rx7club.com/showpost.php...&postcount=103
Did a little digging. . . sorry for the initial laziness. This seems to be the only comparison I can find. Any added strength or weight savings that would make the V161 more desirable? |
Gear ratios only. If there's a good amount of interest in the V160s (USDM), I can prob do those in the GB as well. They're a bit cheaper. But for me, it's all in the gear ratios.
|
I'm sure you could drum up some more people if you had some pricing, at least ballpark, for the V160s. . . maybe even more than for the V161s. I for one am interested in both, but will likely be limited to the V160 by the wallet.
|
awesome find ramy! Did you post something over on the supra forums? Im SURE that you can get ALOT of interest in these over there.
|
Originally Posted by calculon
(Post 7588160)
I'm sure you could drum up some more people if you had some pricing, at least ballpark, for the V160s. . . maybe even more than for the V161s. I for one am interested in both, but will likely be limited to the V160 by the wallet.
Originally Posted by turbodrx7
(Post 7589488)
awesome find ramy! Did you post something over on the supra forums? Im SURE that you can get ALOT of interest in these over there.
~Ramy |
Ramy, any special deals for a full package with trany, adaptor, & clutch? :)
|
Well we're gonna be running a GB for all the parts necessary, even if the GBs are run separately.
|
Ramy are you gonna be able to supply one of these for me when my engine finally gets here and is put in? Its finally on a boat and detuned to these
revs torque (ft/lbs) hp 2000 401 153 2500 401 191 3000 440 251 3500 479 319 4000 468 356 4500 468 401 5000 485 461 5500 479 502 6000 473 541 6500 473 586 7000 473 631 I'll probably miss the GB but will you able to get me one when my transmission breaks? Robert |
HEY ROBERT!!! :wave: :)
Long time man...how goes it? I hope all's well with you? Man...haven't talked to you in AGES. Glad to see you're still around :) Drop me an email man. I'd love to hear the scoop on your project. I'm actually just about to start on mine :D
Originally Posted by Ingraham
(Post 7595666)
Ramy are you gonna be able to supply one of these for me when my engine finally gets here and is put in?
I'll probably miss the GB but will you able to get me one when my transmission breaks? Just recently, apparently TRD needs a bunch more, and I'm able to finagle a few new ones at the same time. So how long will this last? I honestly couldn't tell ya. That's one of the reasons for my urgency in getting this GB done ASAP, cuz I have no idea how long this window of opportunity's gonna last, and frankly speaking, I wanna make sure I get mine before it's too late lol. My advice to you (and anyone else who's serious about getting this tranny) is to get it while it's available. No marketing schemes, no sales hype. I simply can't guarantee they'll be available later. I can't tell ya how long I've been trying to get 'em new as it is...so this is a gold mine IMO. So get 'em while the gettin's good, ya know? Its finally on a boat and detuned to these revs torque (ft/lbs) hp 2000 401 153 2500 401 191 3000 440 251 3500 479 319 4000 468 356 4500 468 401 5000 485 461 5500 479 502 6000 473 541 6500 473 586 7000 473 631 Robert ~Ramy |
Update:
1) Posted up on the SupraForums 2) Here's a nice spreadsheet comparing the V160 (USDM) to the V161 (JDM), provided by our friends @ SupraForums :) http://www.mkiv.com/techarticles/get...ratio_info.xls |
edited, nm :)
|
Will the getrag work with a 20b? Also any info or links on the adapter kit?
|
Originally Posted by Shabib67
(Post 7603937)
Will the getrag work with a 20b?
Also any info or links on the adapter kit? |
I was wondering what kind of adapters are needed and such if buying this transmission. I'm planning on doing an auto-manual swap, and any info would be appreciated. Could lead me into buying one :)
|
Originally Posted by FDNewbie
(Post 7604432)
I already posted the link above... https://www.rx7club.com/showthread.php?t=618433
https://www.rx7club.com/20b-forum-95/tranny-618433/page10/ Sorry to take the thread off topic slightly, but for those that want to buy the adapter kit mentioned in that thread, how would we go about it? I already have a used v160. I live in new zealand and have never imported an item valued over $500 before, so i'm not sure what's involved in obtaining this kit. If we deal with you FDNewbie, i am happy to pay the inquiry fee i briefly read about in another thread. |
Originally Posted by illdrift
(Post 7604826)
Sorry to take the thread off topic slightly, but for those that want to buy the adapter kit mentioned in that thread, how would we go about it? I already have a used v160. I live in new zealand and have never imported an item valued over $500 before, so i'm not sure what's involved in obtaining this kit. If we deal with you FDNewbie, i am happy to pay the inquiry fee i briefly read about in another thread. Thanks, ~Ramy |
Well, it looks like 2 orders will be going through at the end of this month...so if anyone else wants in, NOW'S the time. ALL ABOARD! :)
|
I wish I was rich Ramy LOL I need one of these trannies for my 2jzgte swap into my sc300 but I'll have to use my stock 5 sp tranny for now.
|
All times are GMT -5. The time now is 11:47 PM. |
© 2024 MH Sub I, LLC dba Internet Brands