Hah, that would explain the midrange torque you had coming out of corners at Grande Bend :icon_tup:. I liked what I was seeing there. I wanted to come and say hi to ask about your setup but was busy doing the final tweaks on Jimmy's tune.

thewird

If you're at the 23rd event, swing by our pit area. Would be nice to put a name to a face.

Andrew.

awesome cant wait to see it finished !!

Cleaned up the rotors and put the side seals and corner seals in labeled boxes as I'm thinking about reusing them (after checking clearance) since there in such good shape. Bad news is I have to change all the rotor bearings. Well one is in good shape but since I'm changing the other 2, I'm changing them all. Also all 3 stationary gear bearings need to be changed and the 20b center stationary gear needs to be changed as there is noticeable wear on the gear teeth... I think I'm going to run 20w50 in this motor (in addition to the extra oil mods) just as added precaution, it seems that oiling is significantly more important on the 20b then the 13b, even for a stock one. The 13b never cared what oil I put in it LOL.

https://www.rx7club.com/attachment.p...1&d=1347598517

thewird

great job on the build. Looking forward for the end product and a few vids.

Congrats! look forward to following this build and hearing it running!

what happened with your old engine?..it still kicking?

I have 2 mazda racing competition rotor bearings if you're interested! You doing any side clearancing on those rotors, and are you using extra dowels or a few oversized studs?

Stock bearings for me. I need oil pressure at low RPM since this wont be a full race car :P.

thewird

Center Stay gear will be tough..

Those are NLA

I have a few NOS on the shelf and a few excellent used condition spares..

This guy stocks the forum trying to sell parts LOL. Yah, I was gonna buy one from you LOL.

thewird

I can't wait until you set all new times for your signature lol

You're going to need a cage...

No cage, carbon fiber door, stock seats, and full interior. It will work well I think :icon_tup: . My times are a little behind too I'd say, I haven't run the car at 100% since 2010 due to turbo and other stupid issues/delays.

thewird

Care to elaberate...?


you sent him maps, he did logs, and sent back, then you adjusted..?



I might (if your willing) send you a question or two about learning to tune from scratch (through the PFC group) because of how good you have become and to learn from, basically scratch... which is exactly what I'm just starting to do..

BTW, got the WB in, put it in the stock port like you suggested... so far its working good...



J.

Basically, that's the jist of it. Its a very time consuming procedure that involved a lot of explanations and "try this". Towards the end, it was just a matter of raise boost, give me log, but to get there took a lot of effort.

Got my coils I'm going to use for the 20b :D

https://www.rx7club.com/attachment.p...1&d=1348223363

thewird

Nice to here you lucked out on the motor couldn't have happens to a nicer guy. Good luck with the build look forward to seeing it when it's completed and tearing up the track.

More goodies :D

https://www.rx7club.com/attachment.p...1&d=1348506001

thewird

1:12.xxx - Do it.

I give you 12 months.

It'll be done. But I think I have to put flares on the rear to run 335 on the back :tear:

thewird

Any particular reason you didn't go with the Greddy RE10's to save some $$$?

Greddy's don't have the 10.5 plug. They're the same price as the Greddy's.

thewird

They must have gone up, last time I grabbed some they were over $10 cheaper/plug. Either way it's your money, I was just curious. Project will be BA, I just hope you finally cave one of these days and build a cage! :icon_tup:

Yah, I remember when we could get them for ~$120 /set allin. Not anymore though. I'd still pay more for the 10.5 though, its better suited and the 11 is too cold for street use.

thewird

Man i cant wait to see this thing rip, BTW i wont be scared to go past 20lbs :D probably in a week or so!

Block has been machined to accept 12.7mm through studs :). Added some colors so I can fap to it when needed LOL. Ready to make some torque at high boost reliably :icon_tup:

https://www.rx7club.com/attachment.p...1&d=1350218982
https://www.rx7club.com/attachment.p...1&d=1350218982
https://www.rx7club.com/attachment.p...1&d=1350218982

thewird