Can anyone who has watched my video on Vimeo that I posted just a couple links up comment on the first starting? Does it sound like it was misfiring? Should I have been able to get it to idle longer than about ten seconds?

Here it is again: http://vimeo.com/m/98889437

I've read the rebuild info on rotary resurrection saying that it wont want to idle but I'm just curious how anyone thought it went compared to their own experiences?

Thanks in advance

Got my new starter in the mail and went to work removing the burnt one. The boot that has the positive wire from the battery had completely melted through and so the side of the starter was all black. I tried to buy a new boot but couldnt find one so I just wrapped it with many layers of electrical tape. Hopefully it doesn't happen again?

Attachment 537601

Attachment 537602

Hooked up the battery and it was no longer shorting out. Was able to start the car again which was sick! Such a dope sound with only a Downpipe haha the whole neighbourhood probably knew that I got my car started again. But lots of oil pouring down from unknown locations.

Make sure you have no intake leaks after the AFM. The same thing happened to me the other day when I first started my Turbo swap in my vert. I had removed the stock bypass valve and the vac lines and forgot to plug the holes. It would start then immediately die. Taped up the holes as a temp fix and it started and idled just fine.

Thanks I'll try and move along the system and trace some. Sounds like the same problem

Attachment 537684

The other day my buddy and I bled all the brakes because it was never done after we replaced the master cylinder a while ago. Never bled brakes before so it was something new. Also because when I removed the subframe I of course had to unhook the brake lines and so there was a lot of air. By the last wheel though I noticed a small leak coming from the bottom of the brake master cylinder very slowly I guess it only showed up when we were putting all that pressure on it. I know I saw it leaking before and I tightened it but I think I gotta do it again and use some Teflon tape this time. Can't remember what the line leads to but it's the large 17mm nut with a sensor.

After that we got around to swapping in the S5 tails. I have to say cutting out the section for the s5 license plate light went horribly as I'm not too good with an angle grinder. I recommend making a square cut out instead of trying to make a circular cutout if you're not good at it like me. Luckily no one will ever be able to see that under the taillights. I also had to use some cutters to trim the corner of my tails and my license plate mount where they make contact in order to make them fit.

Attachment 537685

Attachment 537686

The good thing is that all of the lights still work and my new reverse light sensor and extended transmission wiring also works. That reminds me that I still need to solder in a new connector for the 5th gear sensor. I may try and diagnose some of the problems today if I'm not helping my buddy build a sub box.

Attachment 537687

I found the oil leak it's coming from the oil feed or return line (not sure which is which) for the turbo, the larger one which bolts on with two bolts to the oil pump / block. Even with the engine running only for a few seconds (as the AFM was not hooked up) oil was streaming down. I don't have time to fix the problem this weekend but hopefully I can check it out next weekend.

I hope it's just a matter of the bolts not being fully tightened and not a stripped bolt issue. Im planning to just remove it and clean it up and apply some ultra gray. I really hope that's the only leak it's hard to tell as it drips down onto the subframe and then leaks on all sides.

Tore apart my engine bay again to get at the oil leak and I also found a coolant leak from the water pump so I had to reseal up 4 sections by the Time I was done putting It back together

Attachment 538340

The oil leak is fixed but unfortunately the next day I found a small coolant leak still existing

Went to work repainting some yellow paint on my front left trim using trim paint which I used before on my prelude window sills and had really good results with

Attachment 538342

Can never have too much protection from overspray

Attachment 538341

Attachment 538343

Got carried away and started repainting the wiper arms because all the paint had worn away

Attachment 538344

Attachment 538345

Worked out really well definitely recommend to anyone looking to repaint their trim. I have to repaint all the sections of trim on my car later because they all have white overspray from the previous owner. I only had one leftover can to work with. I'll post a photo of the can later in case anyone is interested

As you probably saw from the last post I installed my konig feathers on the rx7. Just had to run out and buy some new 73.1-60.1 mm hub centric rings to get them to fit.

I didn't really want to use them at first for this car but since I already have them I may as well throw them on.

Attachment 538346

Attachment 538347

Attachment 538349

that license plate bezel becomes much easier with a dremel and the proper cutting wheel. I am glad you went ahead and put the S5 tails on your car. As I said before we are twins in color and year, just that now you have braaaap psssshhh and I just have brap. I have been considering putting my S5 tails on my car and swapping my other FC back to S4... but idk.... If I did it I would also bring the Tii wing over as well, and my car is too clean to be drilling holes into to mount a wing to.

EDIT: GODAMNIT! you took my idea straight from my brain!! I was planning on running gold wheels of some sort. Now I know I made the right decision. looks great.

Started to wire up the AEM failsafe gauge though I don't have a bung welded into my Downpipe for it yet and I don't want to use the o2 sensor location because it's way to close to the manifold.

Attachment 538350

The customization software is pretty sick but I don't plan on using the failsafe feature right away. I just want to be able to monitor the afr and boost pressure. I had some poor photos from my phone of the program actually hooked to the gauge but since I'm away all I can upload is screen shots of the program while it's disconnected.

Attachment 538353

Attachment 538354

I ordered an a-pillar gauge pod for an fc rx7 a little while ago and it doesn't even match up properly though it's supposed to?? Maybe I'm doing it wrong. I tries mounting on the passenger side too incase it's a JDM model but it doesn't seem to sit well there either? Either way I'll still be using it

Attachment 538355

Rolled the car out for the first time since I cleaned the engine bay a couple of month ago so that I could wash it. It was bugging me how much dust was accumulating

Attachment 538356

I also bolted up the hood that I unbent and it actually looks ago besides some wrinkling and the missing paint. Also since its from a 10th ae rx7 the white is different from mine and makes the rest of the car look bland haha.

Attachment 538357

Literally gearing up for the first car wash ever haha

Attachment 538358

Comparison shots from the car when I bought it in November till now. It's sad because the last two photos show my totalled prelude which was my previous project vs my new beater Acura. The gold rims are really starting to grow on me now.

Attachment 538361

Attachment 538362

Attachment 538363

Attachment 538364

Haha didn't know you had two FCs that's great. Yeah I have been sortof looking out for a wing to install in the future but im wary about drilling holes. I should've used my dremel for the license plate bezel and the corners of the taillights but I just kept snapping pieces off until it fit haha. I'm thinking about pulling the taillights back out when I have time and redoing the cutouts with an angle grinder as square cut out as opposed to the circular cutouts which I attempted and failed at.

Haha and the gold rims I already had and don't really want to get rid of them because they were a gift so I just bolted them on since I don't have a budget for new rims. They're really starting to grow on me now. A few months ago I photoshopped them on just to see how it looked and I thought it looked terrible but it looks a lot better in real life.

Also I really don't have brap pshhh right now Lool I have no exhaust and a misfiring engine so it's just the loudest beast and scares the hell out of me at fear of another fire. Then after about ten seconds it dies lol

The lights can be made to fit better with a channle lock pliers bending back the metal on the car itself inwards ever so slightly. I was reffering to the actual black plastic garnish that goes between the lights and plate area. I could be mistaking the whole thing as I am nearly 2 whiskeys deep now.

And yes, Twins to the max!

http://s1274.photobucket.com/user/co...nwpe5.jpg.html

never mind the pony tank air compressor in the back. Was its first time on the ground in 20 years. I trust nothing until 200 miles are put on this thing.

Sorry for thread jack. You have certainly made serious progress in short time.

Edit: The only difference is I have 17502 miles less than you on my ODO. (53833km total on my ODO)

I can't seem to load your photo, maybe it will show up soon? Thanks a lot and no problem man it's nice to get some responses on the thread. Damn those are some low kms

yeah, idk wtf is going on with that. Middle click your mouse on the link. It will pop up in new window.

Ohh yeah I opened it on my computer, sick man and damn your sunroof actually works! When you push the buttons on mine you can hear the motor running but the previous owner sealed it shut I guess due to leaks, that's a future project for me.

My Catback came in the mail today! 3 inch straight pipe with a 4 inch tip. eBay exhaust. I figured might as well since I've already got an eBay Downpipe and midpipe and I am pretty tight on cash over the last few months.

I've read reviews that its going to rust like crazy or the mufflers going to burn out but I can always get a new muffler welded on later and I am only summer driving this car. Can't wait to get it on and see how the car runs. But first I need to install the new trailing coil to stop the misfiring. Never had an aftermarket exhaust before so I'm excited.

Attachment 538530

I started to make a video compiling the 6000 still photos taken on the GoPro over the last four months and it's sooo sick to watch. It's nice to sit here without having to do any work and remember all the really tough times throughout the project. When it's done I'll post it up somewhere and share the link. However since the whole thing took so long the video is currently at 20 minutes for 85 % of the footage. But if I made it any faster itd just be a blur. Cant wait to get it all done !

Exhaust installed! Looks dope but I still gotta see it with the car on the ground and actually hear it running. Gotta say I really really hated stretching those exhaust mounting rubber rings made the whole process take way longer than I thought it would. I pulled the Downpipe off because I need to have the wideband sensor welded into it today.

I also installed the trailing ignition coil but it was way too late at light to start the car to test it I'll check it tomorrow hopefully no more misfiring issue.

Attachment 539219

Attachment 539220

Attachment 539221

QUIT DOING THINGS TO YOUR CAR THAT I WAS GOING TO DO !!!! reeee. I live vicariously through you. You richer then me bastard guy you.

Hahaha I'm out of money now so the fun is over

Well it was a good run. Next, you will be installing the seats and steering wheel setup I am after...... STOP IT.

Haha those plans are in my mind but maybe next year. I'm having too much trouble trying to get the engine to idle right now and I'm worried as end up summer is approaching.

I took the Downpipe and the wideband bung to a welding shop to have it welded in and they told me that they couldn't do it because my cheap exhaust is aluminum and the bung is stainless steel. I put the Downpipe back on for now so that I could try running the car. I ordered an AEM no-weld o2 bung for a 3 inch pipe to fix this problem but I don't think it will come for a while.

Tried running the car and it was pretty crappy even with the new trailing coil to correct my old one which did not produce a spark on T2. I cant get the damn car to idle. I'm also pretty sure that while at first the tachometer was showing rpms reading from the trailing coil it soon stopped and
I had to jump the bullet check connectors from the trailing to the leading in order to see anything on the tach. I don't understand why it is not showing up if both T1 and T2 coils are producing a spark.

After giving up trying to get the car to idle I started swapping the fuel pump to the Walbro 255lph with my buddy. It was difficult to relieve fuel pressure as I can barely get the car to stay on long enough to pull the connector going to the fuel pump but I tried my best. Then I detached the flex fuel hose that I had replaced my lines with below the fuel filter to help relieve more fuel pressure. But still when we went to detach the lines at the fuel pump cover it shot out all over the spare tire.

As I was told it would be the screws on the fuel pump cover were totally rusted. I tried four and pretty much stripped them. I was kindof discouraged here because it would mean towing to a shop because I'm not that comfortable with grinding the bolts at risk of another fuel fire. I starting googling and came across aaroncakes website and he said that he managed to get some of the screws off by just hammering the screwdriver to get it to set in the screw. I tried this out and luckily I was able to remove all the screws by doing this so that was a great tip.

Swapping in the fuel pump was much easier than I expected.

Attachment 539632

Went to replace the screws with M4 bolts but couldn't find a store that was open which had them of the right length and had to buy longer ones. I cut them all shorter using an angle grinder and surprisingly enough didnt damage the threads. Ran the car with the new pump and it worked but didnt get the engine to idle as I was sortof hoping it would.

I was looking in the Haynes manual as to why I cant get the engine to idle and one of the suggested problems was incorrect timing. I checked the resistance on the crank angle sensor to see if it was working and the resistance was within spec. Some of my buddies came by and brought a timing light and I began removing components to get access to the eccentric pulley.

I was concerned because I had taken the pulley from my NA engine and so assuming it could be attached any way then the timing mark could be off by 90, 180, or 270 degrees. When we got all the fan and belts removed though we found it was even more serious of a problem because there was no marking on the pulley to indicate the timing position.

Spent a long time researching and looking at my old engine to try and determine where the mark belongs on the pulley. We noticed there was a little circle cut out of the wheel behind the eccentric pulley but couldnt be for sure that this was what was used to mark the pulley. We also tried other suggestions including looking for a certain dimple on the flywheel when looking though the inspection panel on the bottom of the transmission. However I was missing the entire counterweight plate that the website was telling us to look at.

Finally one of my buddies found a link which told us how to make the mark. I can't post the link because he had it on his phone but I can post the instructions here:

How to mark the eccentric pulley for timing
1. Remove the rear rotor spark plugs
2. Then the eccentric shaft using a ratchet and look through the trailing spark plug until you see an Apex seal pass by.
3. When you do, make a mark on the pulley at the pin used for timing.
4. Turn the eccentric shaft until you see the same Apex seal appear in the leading spark plug.
5. Make a mark on the pulley at the pin used for timing.
6. The correct make is directly in between the two marks that you made.

We did this on my old engine because it is easier to access the alarm plugs and look through the side with a light rather than with a mirror in the engine bay. Then we transferred the pulley to the new engine in the car. Turns out I wasn't crazy and the pulley only fits on the shaft one way.

After all of this we checked the timing and it was fine. We tried adjusting the crank angle sensor anyways and it really didn't help and eventually we just put it back to the original position.

So while incorrect timing isn't the cause of my engines inability to idle at least I can rule it out from the list. Not really sure what to check next, I'm fairly sure that there aren't any vacuum leaks.

I decided I wanted to get the AEM failsafe gauge finalized inside the car so that I wouldn't just have wires dangling everywhere.

I passed the wideband cable through the firewall as well as the green wire which will later attach to the trailing or leading ignition coils in order for the gauge to determine rpms. Since I am having trouble with the trailing coil sending the rpms to the tachometer right now and have a jumped to the leading ignition coil I left that green wire for now.

Next I ran the afr cable down along the transmission and tied it up for now as I don't have the bung in my Downpipe yet. Then I wrapped up all the other wires which are for analog output to a data logger and tucked them up in the drivers footwell.

I then removed the a pillar and drilled holes through the a pillar gauge mount using clamps to keep it in the right spot. I trimmed the excess plastic on the pod which annoyingly came an odd shape.

Attachment 539633

I then drilled a 3/4 inch hole in the a pillar for the wires. I took the a piller and gauge pod back to the car and ran the wires and vacuum hose through the hole and hooked them up to the failsafe gauge. Then I attached the pod to the a pillar and reinstalled the a pillar into the car. It looks sick now and it's good to know that the cables can run under the back of the a pillar and aren't getting squashed. I really like the way it looks. I ran the USB cable up under the drivers footwell and tucked it behind the plastic panel on the right side of the footwell.

Attachment 539634

Just to edit what I said earlier today I am NOT sure that there are no vacuum leaks. That will be my next step to check along with checking that the TPS is set correctly

Took the words out of my mouth. Tiny leaks create headaches. One of my last videos shows a make shift smoke machine to hook to any old air compressor with low PSI and smoke bombs. Sure, other things could be used like charcoal and cardboard scraps.

I recall the turbo guys have a place factory installed that can be re purposed for hooking an air hose to hear for leaks as well. I am still NA, and can not confirm.

Thanks I'll check it out

As I said before I've started to make the video compiling the 8000 GoPro photos ive taken during the swap project so I'm going to be posting up some of my favorites where I only posted phone photos before.

GoPro photos from the past little while:

During the subframe drop. My buddy and I trying to drop that bitch down smoothly

Attachment 539753

Borrowed a larger jack from my friend and trying to orient it so that I could roll it as one unit under the back end of the car

Attachment 539754

Torquing on one of the rear BC coilovers

Attachment 539755

Swapping bulbs from the s4 to s5 taillights and a photo of the lights removed

Attachment 539757

Attachment 539756

Lining up the new exhaust to see how it looks

Attachment 539759

With my buddy unhooking my new flex fuel hose below the fuel filter in order to assist with removing some of the fuel pressure before swapping the pump

Attachment 539758

Attachment 539760

Attachment 539761

Using a coat hanger to shove the wideband cables for the AEM failsafe gauge through the firewall. Finalizing the wiring underneath the footwell, removing the a-pillar and drilling it out.

Attachment 539762

Attachment 539763

Attachment 539764

Attachment 539765

Spark plugs removed from the rear rotor on my NA engine and my buddy and I looking inside in order to mark the timing mark onto the eccentric pulley.

Attachment 539766

When I forgot the GoPro was still running and went inside.

Attachment 539768

This weekend I'm trying to correct my idling issue . I started with checking up on my TPS trying to set it properly using the guide on FC3SPro. The TPS is supposed to read 1k at no throttle and under 6k at WOT.

So I checked mine at no throttle and it was reading 5k?! Went to the next step to adjust the idle adjustment screw and it was totally missing. So no wonder. I took one off my NA engine and set it back to 1K. Not sure if I should be setting it a little bit higher since I have no emissions or if I should raise up the throttle stop screw. But I am going to raise that one a bit more. I tried to get the car warmed up a little but it would still only idle for a few seconds. it was too late at night and too loud to try it any longer.

Thanks to archaphil's video of the smoke tester he made my dad made one the same so I'm going to smoke test it for leaks in the morning.

Attachment 540414

Hopefully that leads to some solid results. Also thanks to Satch I'm trying to diagnose my key not shutting off the car issue.

Haha, nice. You do not need a ton of pressure, I think is was around 5-10psi. And cap off the outlets, well technically air inlets with zip-lock baggies and rubber bands (or similar). My method of smoke bombs was tricky in the sense they do not smoke very long. I had a couple people help, one lit it and dropped it in, while another pounded the lid on, then another hooked up to the brake booster while I checked with a flashlight for the colored smoke to pour out.

If I had to do it again, I would of used charcoal and cardboard scraps. They burn longer. And if I was to do it again PRO style, I would wrap wire in one inch loops about 11 coils worth, and hook that up to 12v, then run a wick of some nature and baby oil. Just like a vaporizer. I saw a nifty vaporizer made from a similar endeavor as my paint can.

Hopefully we get it sorted out.

Archaphil I ended up taking your advice and using cardboard scraps and charcoal. It worked very well, almost too well, it was difficult to control the heat produced by the fire inside. I did actually see that video with the baby oil fed smoke tester but that's just too much work for my needs. Still very cool though.

Attachment 540849

I don't have the actual footage from my GoPro here with me but maybe I'll post up a screenshot from it later of the whole setup.

I ended up finding two leaks. One was from the a block off plate for an emissions related component and the other was at one of the three tubes on the back of the UIM which I had capped off. One of the vacuum caps had come off or I had forgotten to cap it. I ended up putting the tube for my failsafe gauge on there since I knew already that it isn't blocked off inside from the smoke streaming out of it.

I took off the block off plate and cleaned it up but then the Paint came off so I repainted it flat black with some exhaust header paint I had laying around and resealed it with some ultra grey.

Attachment 540851

Reattached it and now I could determine that the vacuum leaks were covered. Thinking about it now though I probably should go back and check it again just because the two combined were fairly large leaks and maybe there could be more smaller ones that didn't have enough pressure to see.

So after all this was done I was thinking about it and looking through my Haynes manual in the trouble shooting section and I've sortof covered all the most common issues as to why the car won't stay on without pressing the pedal.

So I decided to raise the idle using the idle stop screw. The guide on rotaryressurrection says that a few turns are necessary so I turned it three times.

I went to start the car and it started and immediately began to idle at 3000 rpm. I had obviously set the idle too high and with the exhaust on it kinda freaked me out. I went to turn off the key and of course it didn't turn off so I went and pulled the EGI comp fuse which I usually pull to turn off all the electronics once I've switched to OFF. However, that didn't turn off the engine and it continued to roar at 3000 rpm. So I pulled the battery and that didn't do anything.

I had read about this problem before when I was researching that my key wouldn't turn off the interior electronics. And I read someone posting about how their car wouldn't turn off and that they had pulled the battery and I just thought well at least I'm not having those problems. Except now I was.

So I was standing there freaking out and I pulled the L1 spark wire and got shocked by the Leading coil pack. The engine started to misfire but just kept on hauling at 3000. I went to pull the L2 spark wire but then I got shocked over and over again by the open L1 outlet.

I considered pulling one of the trailing spark wires but then realized it would probably just start sparking and grounding with the metal components infront of it which happened before when I removed them to see if there was spark.

Finally in desperation I pulled the EGI inj fuse and HEAD fuse at the same time and the engine finally turned off. Honestly I thought it was just going to roar to life again as I was standing there, I was so freaked out. It was the second scariest thing since the fire. So in all, the first idling experience wasn't that chill.

I turned the idle down three turns because I had turned it up a bit more than three when it had reached 3000. The engine sortof sputtered but then began to idle at 1000. Following rotaryressurrection's guide for breaking in rebuilt engines I wanted to raise it to 1500. So I turned the screw up a half turn but since then I have not been able to get the car to turn on again. I'm suspecting low battery. I had to leave for the week so this weekend I'll try it again with a charged battery. Hopefully it will idle and I can actually drive it ?!

Since it wasn't starting my buddy and I removed the brake master cylinder we installed a few months ago because when we did the brake bleeding I noticed it was leaking at the bottom
From the pressure sensor and it was beginning to eat away the paint in my engine bay. It was a bit more of a bitch than when we installed it because at that time the engine was out.

But we got it out and I Teflon taped the sensor this time and it seems to be holding now. So at least I don't have to worry about losing brakes while driving but I will have to re-bleed the system.

Finally, I got in an order of LEDs and changed my reverse light to bright white LEDs instead. I'll have to get a proper picture at night later.

Attachment 540852

I suspected the charcoal might get a tad hot, hence why I went with smoke bombs. But I am glad it found your leaks. It certainly can't hurt to hit it again now that you found the big ones. Minor leaks can still create headaches, especially come time to tune.

You are getting there! I, on the other hand am waiting for a deal on wheels/tires. I just bought the top half of my turbo engine though! so that is something!

Amazing progress, and ar look awesome! Really enjoying reading your work and it's helping me figure out my situation and how I'm going to have to do. Cheers!

That's pretty sweet man, I could use some new tires too, maybe next year. Haha that engine will be more than ready by the time you need it.

Thanks a lot, always appreciate getting some feedback. It's nice to know someone is learning from my experience haha

Attachment 540936

Got my AEM no-weld bung for attaching the wideband sensor to my aluminum Downpipe. Hopefully I can install that on Sunday.

Only had an hour to do stuff today. I tried to bleed the brake master cylinder by disconnecting one of the lines and pumping brake fluid in with a syringe but the pedals still pretty soft. Hopefully I can just bleed the brakes and be done with it because there's not a lot of room to get a syringe in on the other three lines. I forgot to do this process before reinstalling it again.

Tried to start the car with one of my buddies. Took the intercooler off and he was playing with the idle set screw and I was inside starting the car. Almost got it to catch once but finally just gave up for the evening.

I went out and came home and there was a leak which was a piss off.

Attachment 540937

After closer inspection it was fuel. So I guess it was more than flooded.

Attachment 540938

Bunch of fuel was leaking all around the exhaust manifold and turbo. A little bit even dripped out between the Downpipe and midpipe. Guess lack of fuel isn't the problem.. Luckily the car will have two days to dry out before I mess with it again.

Why do you think your downpipe is aluminum? The picture looks like stainless to me. The weld beads look smaller and more of a golden color. Aluminum is rarely used for exhaust and even then, usually only for the back section. The melting point of 6061 Al is 1200F, my EGTs pre-turbo are 1300-1400F at cruise. There are many different varieties of stainless steel, some magnetic, some not. If you are going by whether its magnetic, that's not always an indicator.

Not sure how I feel about that AEM piece. HOLY SHIT though! Get that fuel leak fixed fast!

Have you tried bench bleeding the Master cylinder? It can be done still installed in the car, I personally find it to be more of a PITA that way, but it is doable. Head down to NAPA or whatever is convenient and pick up a couple bleed kits ( they will know what you are talking about if you say you are bench bleeding).

They are cheap and come with plastic plugs that screw into the MC where the brake lines go, then run a rubber hose (comes in the kit) off each nipple back into the MC reservoir submerged completely in Brake fluid so no air can come back in. Then pump pump pump it up. Trick part is getting the lines hooked back up quickly. After that, bleed the lines as normal at the calipers and you should be golden.

I took the Downpipe to a welding shop to get them to drill a hole and weld in the bung which came with the wideband sensor and they said they couldn't do it because it was aluminum. The website said that it was stainless steel but I wasn't going to argue with the guy since his profession is in welding. Guess he just didn't want to do it..

I bought the AEM piece also because I could install that myself. I was tired of chasing around parts and services at shops and having these old guys tell me they don't know what I'm talking about. Since I only work on the car on evenings and also late at night it's difficult to work within the working hours of local shops.

I don't really like the AEM piece either but I did see a post somewhere where they did a review to test it up to a high pressure and it seemed to hold up okay. Also in the post I just wrote up there I got fed up with having to race home to get to shops within their business hours and the AEM no-weld bung I can install on my own time.

As for the bench bleeding I did remember to do it the first time I installed the brake master cylinder in april but I forgot to do it when I reinstalled it this week. I'm probably just going to try popping off the other two lines and injecting them with the syringe as well until I stop seeing the bubbles. If I have no room for the syringe then either I'll have to take it out or buy the bleeding tubes as you said I could probably find.

I just tried to drill the hole into the Downpipe but the bit wasn't strong enough because I thought I would be drilling into aluminum.. thanks to that fucking welder. So I gotta get a new bit this week

Is it really a fuel leak though? It was fuel that wasn't being consumed since I was cranking the car and jt wasn't starting. I'm inexperienced with this. If I crank the car over and over for like twenty minutes (ten seconds on and then a break) and continue to flood it without actually starting the car then will this always happen to everyone? Or is it strange that it just happened to me? Is it safe to start the car if this is happening? I assume the unused fuel has to go out the Downpipe if it isn't being burned in the rotors? But that usually the car just starts and this problem doesn't happen.

Installed the AEM no-weld bung on my Downpipe yesterday. Was very very difficult to drill the hole for the sensor. But in the end i got brought and the wideband is all wired up.

Attachment 541555

Attachment 541556

Unfortunately I haven't got the car to run since two weekends ago. Can't figure out what's wrong but the last thing I did was lower the idle set screw so I've been messing around with it and can't get it to go.

Any suggestions on how to adjust the throttle body screws if they been completely out of whack would be greatly appreciated. The only two screws I know of are the idle set screw an the TPS sensor adjust screw. I don't know what the others do and I don't know how to set the idle set screw.

Thanks

I haven't updated in a long time so its time to explain exactly what happened since august!

I had a goal to get the car running by the end of summer and when the problems started to pile up and I realized I wouldnt be able to have the car running I got kinda sad and decided to step away from working on the car for a few weekends. After working 20 straight weekends in a row I needed a bit of a break anyways. But now I've made some good progress and am back on track!

So after I installed in the wideband sensor into the downpipe I wanted to focus on trying to adjust the idle set screw to get the car to idle again. I turned the idle set screw way down because before I had been starting the car by playing with the throttle so I planned to try that again. After a bit of cranking I would pull the EGI INJ fuse and crank some more to try and unflood the engine. At this point I assume the engine was very flooded as there was still fuel leaking under the downpipe/turbo area, and the engine wasnt making any sounds that pointed towards it trying to start.

I knew I had air fuel and spark now so I assumed that it was just something to do with the idle set screw causing there to be too much or not enough fuel. Suddenly though while I was trying to start, I turned the key to ignition and the whole system made a click and shorted out. I had to disconnect the battery terminal to get it to come back, tried again, and the same thing happened. And then once again the same thing.

I wasn't really sure what had happened here, but I decided it was a short involving the starter. With a buddy I removed the starter from the car and using a battery and jumper cables we tried the starter outside of the car. It seemed to work fine and determined that must not be the problem.

Then we tried hooking the negative terminal on the starter back up to its mount but without the starter in the car, and tried to turn the key. This time the car didn't short out? So i then determined it must be the third wire on the starter shorting out somewhere in the harness. I checked the haynes manual and tried to locate the starter relay in the engine bay but it didn't seem to be where it was supposed to be. There is a bosch relay that always looked out of place and we assumed it to be the starter relay. Using a multimeter, we checked continuity on each of the wires on the bosch relay in connectivity with the third starter wire under the car and all of the wires had some resistance but had connectivity. We tried checking its continuity with other items in the car and found it to have some resistance with everything, including the shock towers?

At this point I decided that the third starter wire must be shorting out somewhere along the harness, caused by the fire that started when my old starter shorted out a couple of months ago. I assumed that over time and from that initial short, the insulation on the third starter wire slowly deteriorated and was now shorting out somewhere in the harness.

While all of this was going on, I was also working with the help of Satch to determine why my warning lights, radio, turn signals all were staying on even after turning the key to the OFF position and removing the key. The only way to turn off these items after turning the car ON and OFF was to either pull the EGI INJ fuse or disconnect the battery negative terminal. So all this time whenever I turned the car on I would have to get someone to pull the fuse in order to turn off all the systems. When pulled, we could hear a loud click sound of something electrical switching off. Satch helped me to check my ignition switch, and main relay, but neither proved to be defective.

Satch recommended pulling fuses which were connected to the ignition switch to see which was backfeeding the circuit, and keep pulling them until all of the items turned off. It turned out that the ENGINE fuse in the drivers footwell was backfeeding all of the items, and when I pulled it they switched off. However, as soon as I replaced the fuse they all came back on meaning that whatever was powering it was not effected from the interior end of things, and would continue running regardless until I pulled the EGI INJ fues/pulled negative battery terminal. Checking the wiring diagrams I believe this fuse is coming off the two wires on the back of the alternator.

Satch pointed me to previous posts that show how to wire the alternator when swapping a T2 engine into an NA vehicle, something that I had never done. I always saw the post in the TECH section of rotaryresurrection, but the guy who I bought my engine from told me that everything was already wired up and it was direct plug in play. Turns out you can't trust everyone.. The alternator and coolant temperature sensor had to be rewired. This explained why my coolant temp gauge inside the car wasn't working, I thought it was probably a faulty sensor.

I mentioned earlier how I had the problem with the engine not switching off the only time I got it to run (at 3000rpm). So with the shorting starter, the engine not switching off, and the new wiring that had to be done, there was clearly no chance in getting the car to run before the end of summer, I decided to take a break, and this is where I left it for a month.

I installed some bright white reverse LEDs a while ago but think I forgot to post pictures. Unfortunately I don't have any of them completely in the dark.

Attachment 544849

Attachment 544850

Oem vs LED

Attachment 544851