I can't remember the brand name, but it got it off of eBay. It's a 3 row radiator

Thanks to Curtis I now have all brand new Mooge tie rods and adj. sleeves and one brand new sparco seat! I'm waiting on one tie rod end as he didn't have all them and looking for another seat..... Which I'm going to get another new one so they match lol. Great part is that I fit great in the seat lmao so I don't have to drop 100lbs hahaha. Hopefully I can start working on it soon as it's been pretty cold out.

Sparco r100
Attachment 652823
Tie rods and sleeves
Attachment 652824

Was that Curtis shaw? Is he getting out of the game? Seems like he is selling off an awful lot of stuff.

Yes... He's always selling his stuff lol

Got a wink mirror for the 7. Just getting it ready for installation!


Attachment 652483

Had a couple of nice days and BAMMMMMM stuff sarts happening again lol.

http://i648.photobucket.com/albums/u...psea7589e6.jpg
Attachment 650463
Attachment 650464
Attachment 650465

Started tearing the door panel apart to use as a templet
Attachment 650466
Attachment 650467

Went to school early today and made my new door panels and seat rails. Door panels still need a little fine tuning then sanded. Seat rails will need to be mounted then determin where the seat will mount on them.

Attachment 650358
Attachment 650359

Installed the door panels today and mounted the seat. Still need a few modifications, but for it bring my first time on this stuff it's not bad!

Attachment 650069

I like the door panels. Aluminum?

Thanks! No they are thin gauge steel. Made them out of what we had lying around at the shop

After doing the brakes and a tune up on the rx8 I spent about 5hrs on the 7 this weekend. Timing is set, carb is tightened down, fuel lines done, and cleaned the dust out lol. Need to finish tightening the oil lines down and the clutch pedal. Still need coils, e-fan, battery, and a couple other little things before I can fire it up finally. Oh and the dreaded wiring lol

Test fit
Attachment 648642
Everything is pretty close, but it fit pretty good
Attachment 648643
http://i648.photobucket.com/albums/u...psdab824e4.jpg
Attachment 648644
http://i648.photobucket.com/albums/u...psf5753554.jpg
Attachment 648645
Attachment 648646
Attachment 648647

This is one sick looking ride! Love it and love to see the progress.

Thanks! It's not as good as I want it to be, but in due time it shall ;)

I didn't know they still made Wink Mirrors. Haven't seen one in years. Would never work for me in this car.. I'm looking through the top 25% of the windshield as it is.. LOL

They still make a few different wink mirrors. Lol I'm 6'1" so I feel your pain. My sparco seat is mounted to the floor so I sit pretty low in the car and it's great!

Been pretty lazy on the at lately. I did get all the fluids and the clutch ready to go. Still need to put the finishing touches on the seat rials and get my ignition coils and electric fan. Going to be relocating the battery and adding a battery cutoff on the rear driver side B-pillar

Seat looks good Mike, and no... even though everything is usually always for sale, i'm not getting out of the game lol

Thanks Curtis! I'm pretty pleased with the seat! Now I just need to get a second one. I'll have to take measurements to get the same one. Ya it's pretty hard to leave the scene lmao I've tried

Well guys I'm not sure how the widebody is going to workout..... I contacted the company that sells the body kit that I'm going to be using and they said that they only have 1 more kit in stock and once it's gone they will no longer sell it. I don't have the money to buy it and might not for a while. So I'm not sure what the future holds :'(

Started installing the headlight buckets, motors, and new headlights.

Cleaned and painted
Attachment 645990
All mounted up and ready for use
Attachment 645991

Thanks to mr Dave Jones (Mazdave) I got a replacement arm for the driver side motor that I lost somehow. Tomorrow I plan on replacing the pitman arm and installing all new tie rod ends for the steering along with new bolts

Started reapplying ALL the bolts under the hood as well as starting a wire tuck. Yes..... It sucks! I have stripped the harness down and started cutting wires. We will see how it turns out. Headlight wires are ran so far.
Attachment 645933
Attachment 645934
Attachment 645935
Attachment 645936

Still need to figure out what to do with all these wires...
Attachment 645931

And try to remember what these went to lol
Attachment 645932

Final product for the direct fire ignition coil mount. Had to shorten it about an inch for a good fit. Needs a little sanding and paint, then it's ready to go!

Attachment 645830
Attachment 645831

Painted and ready to go! Pics sucks, but I'll get better ones before I install it...

Attachment 645740
Attachment 645741
Attachment 645742

:lol::lol: Good luck with that haha. Not sure if its just the photo but that lower rad hose looks a bit kinked?

Good progress lately though man! Those coil brackets look sweeet:nod: