My 93 build.
10 Attachment(s)
Hi lads/ ladies.
My name is Michael and I purchased my 1993 rx7 in August 2011. I bought it with the intention of carrying out a rebuild and on the 03rd of January 2012 I started. Attachment 686394 Attachment 686395 Started ripping everything out. Attachment 686396 With all the correct tools :nod: This beauty was used to reach the top gearbox bolts. Attachment 686397 Two wasn't enough so added another, cost me a roll of frosted sellotape :egrin: but it worked. Attachment 686398 My assistant left me after we had the UIM removed and he saw the rats nest. So I labelled everything up seeing as there is very little help if something goes wrong over here with a rotary. Attachment 686399 Attachment 686400 Attachment 686401 Attachment 686402 Getting tidy. Attachment 686403 |
10 Attachment(s)
Size comparison to a size 9 shoe
Attachment 686379 Got it open eventually with the help of a 55mm socket, 2 meter extension bar and a few friend to hold it down:lol: Attachment 686380 Attachment 686381 Front rotor and housing were scrap Attachment 686382 Attachment 686383 Attachment 686384 Luckily I managed to find a car being broken fairly close by with a blown engine, so I went down with my toolbox and tore his engine apart taking the only salvageable part. 1 rotor. I then gave a few people a call on Irish rotary and tracked down a good condition rotor housing from a 2000 car. At this point I purchased the rebuild kit from Atkins and started cleaning everything. Attachment 686385 Rebuilt solenoid rack, all new silicone hoses and replaced the majority of solenoids. Not fun checking everyone of them with a mityvac Attachment 686386 Started polishing my UIM and painting pulleys. Attachment 686387 Cat seemed to like the car being broken Attachment 686388 |
8 Attachment(s)
Removed the aircon and air pump seeing as the cat had blown itself up (thats what caused the engine to fail).
Created my own block off plates use the side of an old pc:lol: Attachment 686363 Desk ornaments. E-Shaft is scrap due to the pilot bearing burning out inside due to previous owner not installing the seal. Attachment 686364 Got some new to me Bilstein shocks and a fully working cluster. Attachment 686365 Attachment 686366 Yay, more cats. :icon_tdow Attachment 686367 Tried a new cat in my exhaust system, it didn't want to stay in there either though haha:lol: Attachment 686368 Went to a dyno day with a few silvias and rx7s. Engine room at the garage. RB33 Attachment 686369 Attachment 686370 |
10 Attachment(s)
Got my new polyurethane engine mounts and modified the aluminium mount to fit.
Attachment 686350 So the dyno day inspired me to get the finger out and I started my build, unfortunatly I got so involved I forgot to take any pictures. All I can say is there are very few things vaseline can't be used for:lol: Finished up with this after 9 hours cleaning and 2 hours assembly. Attachment 686351 Flywheel back on:icon_tup: Attachment 686352 Attachment 686353 Got some nice new aluminium pulleys to underdrive the waterpump and a GReddy elbow. Attachment 686354 Attachment 686355 Attachment 686356 Saw it on here somewhere so removed UIM casting lines Attachment 686357 With the help of a friend Attachment 686358 Attachment 686359 |
7 Attachment(s)
Heat wrapped my downpipe and collected a high flow magnaflow cat a few miles from me:icon_tup:
Attachment 686343 Everything back in:nod: nearly ready to go. Attachment 686344 Attachment 686345 Changed to an efini y-pipe at the last minute, very difficult to change due to the steering column:( I polished it before it went in. Attachment 686346 My father gave me a hand starting it for the first time. We connected jumper cables, pulled the egi fuse and cranked it over a few time to get oil flowing. I then put the egi fuse in and jumped the fuel pump with gnd in the diagnostic box to prime the fuel system. Started first turn of the key. Great success:nod::icon_tup: Once it was going I decided the stock intercooler needed replacing so got a GReddy SMIC. Attachment 686347 Bumper on haha Attachment 686348 Attachment 686349 |
7 Attachment(s)
Made some 99 spec rear lights
Attachment 686328 On the hunt for reliability I wanted a cold air intake. This system was never going to work. Attachment 686329 I used the standard airbox as I didn't believe the blitz filters were helping. Cleaned up the back of it by deleting some of the outlets I no longer needed:nod: Attachment 686330 Cheap b*****d air intake Attachment 686331 Attachment 686332 Drove the car for about 400 km's before I burst the standard rad. Ordered a new Koyo N-Flo rad and Mishimoto radiator hoses. Car pretty much sat for 4 weeks waiting for the rad. Decided to change the water pump while I was waiting. Attachment 686333 Finally got going again and started on the interior. I wanted minimal fuss so I got a mx5 nardi wheel, RE-Amemiya gearknob, RE-Amemiya boost gauge and steering column cowling and Rmajic PFC commander holder. Also relocated my Swoosh WAFT under the radio so you only really notice it when it light up. Attachment 686334 |
10 Attachment(s)
Got my car tuned by the same guys who hosted the dyno day. I was a little worried but one of the mechanics owns a street ported single turbo fd.
Went down and they were brilliant. Really felt they knew what they were doing even though they hadn't a lot of experience with rotaries. Darren McNamara had his car tuned at the same place the day before I was there. Anyway got the car mapped nice and safe. Attachment 686318 Attachment 686319 Now would be a good time to enjoy the car:lol: But a cat changed his mind crossing the road infront of me and ruined my front bumper. Oh well I was just looking for an excuse to get a 99 spec. Picked up this plateless version in the UK. Attachment 686320 Attachment 686321 Hours of prep time went into this bumper 9+. Finally got it primed Attachment 686322 Then sanded off again Attachment 686323 Finally Attachment 686324 Attachment 686325 Polished it up and fitted Attachment 686326 Attachment 686327 |
4 Attachment(s)
Fitted lookalike 99 spec fog lights. Took a bit of work to get them in the right position but with the right amount of time anything can happen:egrin:
Attachment 686314 Attachment 686315 Got a 99 spec spoiler:nod: Always been my favorite choice of spoiler for the fd. Attachment 686316 As it sits at the moment Attachment 686317 That's it for now, should have an update tomorrow as I just washed it and plan on going to a show in the morning. |
Very well done. I'm not sure you need to retain those bands around your poly motor mounts though. Though I hope you installed the heat shield on the driver's side mount :)
|
Originally Posted by gmonsen
(Post 11336446)
Mcon... Nice job all round. Are you on the Irish rotary forum? Post up pictures from the show?
Gordon Pictures of the show when I get them. I was only rotary present but there was a 2012 Ferrari 458 Italia in pearl white. Spent the remainder of the day fitting a turbo timer to a friends yellow RS-R. Will get pics of that up soon also. Must ask his permission. The band was used to hold the mount together. No heat shield on the mount, I think my car is different from the US version as I don't have a pre cat as standard. |
Nice job on the build and thank you for all the picts. Really helps with some ideas!
|
Nice work.Now that you have a 99 spec bumper remove the upper piece of the undertray-you dont need it and it looks ugly as fk.
|
Looks great with the 99-spec bits. Now give it a wash! :D
|
Very nice looks great! like it very clean :)
|
All times are GMT -5. The time now is 11:20 AM. |
© 2024 MH Sub I, LLC dba Internet Brands