Thanks for the reply. I'm in the process of mounting the almost same exact kit in my FD. Engine bay is looking killer.:icon_tup:

Prrex... Nice man!! you should post some pics when your done!! i don't even mind if you post them in here just so I don't have to look around for em haha.


So I did a little bit of cleaning again today. Cleaned up a whole of wiring and organized some lines/wires as well. I forgot to take a picture of before...but i guess you'll have to take my word for it that it looks way better haha.
Also... I am contemplating wrapping the whole thing with heat reflective.. or just re-painting it nice black.. not sure if it would be an over-kill or not though... we'll see...
http://i804.photobucket.com/albums/y...420_185958.jpg

Alrighty... So today I finally bought a jack... its pretty damn nice.. and I luckily knew the girl that I asked to help me.. she just gained a lot.. A LOT of weight.. so I didn't recognize her at first. But I got it for 60 bucks.. lowest point is 2-3/4 Inches!!! 2 Ton capacity. Hell of a deal! But I pulled my rear diffusor off and decided to give it a good clean. Then I went over the under/top side with a dark Sealer but it ended up being flat... So i'll have to go get a gloss tomorrow. Either way It looks much much better than before.
before
http://i804.photobucket.com/albums/y...426_183034.jpg
After
http://i804.photobucket.com/albums/y...426_221252.jpg
Also, I spent a long time making both sides equally measured... went with this setting to pull out some of the camber and see if my wheels still fit... We'll see tomorrow morning when I put the car on the ground..but i'm almost positive they'll rub.
http://i804.photobucket.com/albums/y...426_221615.jpg

is that the water meth controller? id be careful with that... imo doesnt seem like a great place to put it..

awesome build!

yes sir... why's that? I was thinking of putting it closer to the igniter, actually right next to it, on the fender wall.

Thanks everyone for the Comments!!:icon_tup:

Looks nice~

Meanwhile.... pulled the tranny to start cleaning the tunnel out and get all that bloody oil off EVERYTHING! And me being a little absent minded... okay okay.. being a complete moron forgot to drain my fluid out.. Result; one hell of a mess..
http://i804.photobucket.com/albums/y...428_172542.jpg
good thing I have degreaser though... cleaned up pretty good.
http://i804.photobucket.com/albums/y...428_180418.jpg
And also forgot to post a pic of my diffusor.. sealed the top of it so it didnt look so damn ashy.. haha.
http://i804.photobucket.com/albums/y...428_193825.jpg
up close
http://i804.photobucket.com/albums/y...428_193855.jpg

Is you car supported by bricks?

I know someone was gonna say that. I have two jack-stands in the rear and the bricks are there to balance the car out a little. There's also a floor jack supporting the front of the car. It's actually really sturdy...believe me haha. I've used bricks my whole life really though with no problem.

Well the reason why I brought it up, is because I used to use bricks too till one of them cracked and crumble and the car fell on my buddy's leg braking it.

Can't wait to see this done Aaron, I have been contemplating of tearing the car down and re-building..I guess if my motor blows that will give me a reason.

jack stands are cheap at harbor freight, I really see no reason to be using something brittle like bricks.

nice build manny!! Do you have the part number for the extended studs please?! Whats the knurl measurement on them?

You guys are right... I'm just being dumb and lazy. I'll get some tomorrow morning...well after the Arsenal Man U game. LETS GO ARSENAL!!!

Yea me too man !! And thank you!.I hope to get done before this years seven stock.. that'd be a shame to miss driving this year.. :icon_tdow

How many miles are on your motor so far?

ahh shiiii I can't remember the part number.. but I got them from Summit Racing or jegs a long time ago.. do a search:nod:

And some work I got done today.. Re routed all my wiring under my car for my AEM water meth kit, ground, etc.. it was all gucked with oil too.. took me a long time to clean it off. But got the PPF out.. cleaned it, Got the heat shielding out... Cleaned it.. Cleaned more of the tranny tunnel, and my transmission got de-greased.. But I may go over it one more time.. I don't think i'm going to paint the trans.. I hate when the paint starts toflake off and it looks all cheezy.. but check it!
Pics!!
clean trans
http://i804.photobucket.com/albums/y...430_164027.jpg
Clean shields
http://i804.photobucket.com/albums/y...430_173142.jpg
dirty, oily PPF
http://i804.photobucket.com/albums/y...430_170220.jpg
nice and clean PPF
http://i804.photobucket.com/albums/y...430_203527.jpg
and my tranny tunnel started to clean it..
http://i804.photobucket.com/albums/y...430_164856.jpg

Motor has about 21,000 miles on it but still running strong, cross my fingers...:icon_tup:

Just put the time in and you should get it done by sevenstock...

Excellent build and write up....I'm heavily debating the idea of getting back into an RX7. Been away from them for a while, but this was an enjoyable thread to read and kind of relive the old rotary days. I like my C6Z, but I cared more about my FD's....dunno. We'll see. Excellent build and write up....looks like Vosko is back on here as well. I thought he left FD's before I did.

hey mannykiller nice build im currently working on my control arms and wanted to know where you got the bushings and do they come as a kit id like to replace mine while everything is apart

Thank you!! And...Oh I dare you to get back into one.... It's all about what makes us happy am I right? I mean.. I had a couple other cars before my fd.. and I loved them.. but theres something about meeting your soul mate in the form of an automobile that can't be traded for anything. For me it's the fd :icon_tup:

Contact Rishie at Autornd. He'll set you up with the bushing kit I used. Also, you might want to replace the pillow balls as well. There are 6 of them.. and believe me.. they probly need to be replaced. Malloy mazda has them and there is a group buy in the group buy section for atomic rx7 pillow balls which are great quality as well but a little cheaper.. check it out brotha!!

- ap

Dude I am re glassing my diffuser. A piece of wood on the freeway had fun with it at 80mph.

Also my buddy Danny pin-stripes a lot of motorcycle tanks and helmets... So I asked him if he could do my helmet. He asked me what I wanted on it and I said something kinda simple.. But I wanted the word "Drive" on the back.. I think it came out pretty bad ass..

http://i804.photobucket.com/albums/y...501_003313.jpg
http://i804.photobucket.com/albums/y...501_003335.jpg

This is inspiring!

Keep at it.