4 Attachment(s)
Hey Everyone,
I decided to do a "build thread" but really it is to keep track of what I do to the car. I will try to post as much pictures as possible so it is somewhat entertaining for you all. I have owned a few FDs but this is the one I hope to hang on to. 62k Miles on the body, 3k on rebuilt street ported engine done by Rick at Ricks Rotary Performance. The car had been sitting in a garage for 8 years before the owner decided it was time to sell her. Here are the mods: Street Ported Engine M2 IC and Air Box Power FC Mazda Performance Radiator Deleted AST Short Shifter Ground Control with GAB shocks Downpipe- wrapped and jet hot coated Bonez Hiflow Cat PFS catback New 99 spec turbos Efini ypipe And other small things here and there Here are some pics taken the day I bought it: Attachment 624177 Attachment 624178 Attachment 624179 Attachment 624180 |
3 Attachment(s)
So far I have:
Replaced the Coolant Changed the Oil Changed the brakes Replaced the Brake Fluid completely (full drain and replace) Replace the Tires with New Potenza RE-11As Old Brake Fluid that was drained Attachment 624174 New brakes going in. The owner had a set of Hawks that he used for a little while that he included with the car. I decided to just install those since they had a lot of meat on them. The previous owner had speed bleeders installed so bleeding the fluid was easier. Attachment 624175 New Tires being installed. Attachment 624176 |
2 Attachment(s)
Did a few simple upgrades.
New OEM Tan Floor Mats and cleaned the seats. I did a lot of research on a good way to re-soften the leather and I kept seeing people using Bag Balm on their seats. I decided to try it and it works great. My leather is super soft and most of the creases are opened up. Attachment 619644 Attachment 619645 |
3 Attachment(s)
Bought a few goodies. New R1 lip, HKS twin power & Power FC holder.
Attachment 619358 Attachment 619359 Attachment 619360 |
Originally Posted by ArmAnirx7
(Post 11926133)
|
^ yea I got the RE-11a's all around. I did a lot of research on tires before pulling the trigger and these tires took the cake. I haven't had a chance to do some spirited driving on them yet but hopefully after I get a tune I will be hitting the track to try them out.
|
4 Attachment(s)
Quick Update:
Got my dual oil coolers! I bought dual oil cooler lines and a Mocal thermostat from a memeber a little over 4 months ago and I finally picked up two 25 Row Setrab oil coolers to complete the setup. I am hoping to install these in the next few weeks. I need to figure out the bracket situation and the ducting. Attachment 618820 I have the OEM ducting for the R1 oil coolers. I am running a 93 stock bumper. Has anyone modified the OEM ducts to fit the 25 row coolers? Here is a few pics of the cooler with the OEM ducting. Is this enough coverage if I were to track the car, or do I need to modify the ducts? Attachment 618821 Attachment 618822 Attachment 618823 |
That looks like it should be pretty easy to make larger shrouds. You can just extend the shroud up with aluminum.
|
Originally Posted by 04G35S
(Post 11990929)
That looks like it should be pretty easy to make larger shrouds. You can just extend the shroud up with aluminum.
|
8 Attachment(s)
It's been a few weeks since I update this thread. I have been preparing to install my oil coolers but I am waiting to borrow my parent's garage before I begin. It is way to cold now to work outside.
In the meantime.. I have been working on a few little items. I notice that the thermostat I purchased from a forum member did not come with a bracket so I decided to make one. Attachment 618271 Next, I decided to fabricated a duct that would fit my 25 row coolers by incorporating the original ducting. After taking a few careful measurements and making a few templates, this is what I came up with. *Shout out to SilverTRD for lending a hand (plasti dip that shit! lol) Attachment 618272 Cutting a few pieces from the original ducting and test fitting my final product. Attachment 618273 Attachment 618274 Final product. (the blue tape is there to hold the cardboard on the other side so the fins don't get damaged). Attachment 618275 Attachment 618276 Finally, I found a deal on a Nardi Steering Wheel and I decided to buy it. It has some wear, but for the price, it was worth it. After cleaning it and treating the leather, this is how it came out. Attachment 618277 Attachment 618278 Stay tuned for more updates in the next week or so.. Thanks for reading |
oil cooler ducts are looking good and the interior looks so much better with an updated steering wheel.
|
Originally Posted by Johnny Kommavongsa
(Post 11998198)
oil cooler ducts are looking good and the interior looks so much better with an updated steering wheel.
|
Originally Posted by ArmAnirx7
(Post 11998237)
Thank you. I agree about the steering wheel. The only thing that bothers me is that my interior is in great shape and this steering wheel is not in that great of shape. I may hold off and see if I can find one in much better condition.
|
Originally Posted by 7_rocket
(Post 11998319)
Why don't you cover it like you did with your other wheel?
|
He must think you're armenmaxx...
|
Originally Posted by ArmAnirx7
(Post 11998326)
You must have the wrong guy. I haven't covered any wheels in the past.
Originally Posted by silverTRD
(Post 11998363)
He must think you're armenmaxx...
You can try this guy if you please https://www.rx7club.com/detailing-re...-brake-911397/ |
Originally Posted by 7_rocket
(Post 11998738)
|
Oil coolers look good, love that clean tan interior :icon_tup:
|
Originally Posted by ZE Power MX6
(Post 11999037)
Oil coolers look good, love that clean tan interior :icon_tup:
|
6 Attachment(s)
Quick update:
December 05, 2015 The car is placed in its temporary home for a few weeks. I also set up my items on my son's lego table. I know what you guys are thinking...yes, I have stacked the legos as high as possible before Attachment 617884 Tear down begins! Attachment 617885 Attachment 617886 Attachment 617887 Credit to SilverTRD for taking the UIM off. Thanks Bud. December 10, 2015 At it again. Tested fitted the oil cooler with the custom ducting and BAM! it fit nicely (with some minor mods to the custom brackets). Sorry no pic of the test fit because I was too excited that it actually fit that I forgot to take a picture. However, I did take some pictures of my oil lines with the clamps installed. Something small but I'm proud of my accomplishment :) Attachment 617888 December 12, 2015 Finally got the rats nest out and the fuel rails out. I need to drop off the injectors to RC for some nice cleaning action. Attachment 617889 I called it a day because I ordered a few items that I need in order to proceed. 1. New silicone vacuum hoses ordered from boostcontroller.com. Went with the Turbologic hoses. 2. New Check Valves ordered from DaleClark 3. Passenger side oil cooler duct ordered from a forum member. |
2 Attachment(s)
December 11, 2015
Received my silicone vacuum hoses. December 13, 2015 Started the vaccum hose job. Here is a trick I am going to use. I decided to go ahead and replace the vacuum hoses that connect from the rats nest onto the rats nest (hence the zip ties. I than removed the hoses that connect from the rats nest onto another component on the engine and I measured and cut a silicone hose but I did NOT install it. The reason is that the rubber hoses are already form in the shape of where they connect. When I re-install the rats nest, it will be easier to see where the rubber hoses once connected and at the moment, all i have to do is take the pre-cut silicone hose and swap it out real fast. I figure that this might help me cut down on confusion (even though I printed out a poster size picture of the vacuum diagram) *You can see the ones that have zipties are all complete and on the upper left corner you can see my precut silicone hoses. Attachment 617882 I also decided to go ahead and primer my r1 stut bar that I have had for a while. Attachment 617883 |
Finally update for today
2 days after I ordered the passenger side cooler from a forum member, I get a text from another forum member andrew j.86 and he says he has a FULL r1 oil cooler setup for sale. https://www.rx7club.com/west-sale-wa...olers-1093389/ I want to thank Andrew for contacting me and this deal was too good to pass up. He even delivered it to me with extra cash I added to the sale price. I truly appreciated that and now I can continue my build without having to wait for the other cooler duct to arrive in the mail. I have found that most RX7 owners are really down to earth people that enjoy helping each other out. It makes being a RX7 owner just a bit sweeter when you have a community of like minded individuals around you. |
2 Attachment(s)
December 14, 2015
I dropped off my injectors to RC at 8:30 am and they had it ready for me at 2pm! Awesome company. Here are the results. I'm glad I got them cleaned before I take the car in for a tune. Attachment 617824 Attachment 617825 |
1 Attachment(s)
So I got a lot done since my last update.
I put the injectors back in, my vacuum hoses all changes out (under the upper intake manifold only). My turbos are new and after inspecting the rubber hoses on the turbos they looked to be new so I left the be. I also go the upper intake manifold back on. Attachment 617054 After putting the oil and adding more coolant, I started the car but I instantly knew I had an issue. Here is the video. http://vid1343.photobucket.com/album...psvbbwkrv8.mp4 Turns out I forgot to attach the vacuum hose on the map sensor. I got that hooked up and the car was running as it should. |
5 Attachment(s)
I finally go around to getting the elbow and intercooler installed and I thought I would take the car out of the garage for a breather.
Attachment 617042 Attachment 617043 I took the car out for a drive to see if the AN fitting will hold the oil pressure. Fingers crossed X and I had no leaks (for now). I decided to put the bumper on at this point and the ducting fit like a glove. Attachment 617044 Attachment 617045 I finished up the engine bay and bolted up the bumper. Attachment 617046 |
All times are GMT -5. The time now is 04:24 AM. |
© 2024 MH Sub I, LLC dba Internet Brands