Replaced my oil pressure and water temp gauges
Well, after the V8 swap I was left without functional gauges for both my oil pressure and water temp. After 2 months of driving around everyday without that information available to me I decided to do something about it.
Since the stock gauges never worked very well anyways, and because I didn't have the Mazda senders anymore I decided to go with aftermarket gauges. I went with the Defi D-Series because they're amber and the font is pretty close to the stock gagues. And, since I'd seen Max Cooper's setup with his in dash SPA gauges, that's the route I took. It turned out OK and reasonably clean. There are some details to it that still bug me a little, but by and large I am happy that I'll have some functional gauges, and I didn;t have to mount them on the A pillar or at the speaker channel. Those areas will be open for boost, EGT, and Fuel pressure when I get around to turboing the car. :bigthumb: Here's some pictures for those that are curious/want to criticize. ;) |
First step was to get everything apart and then dremel out the area to mount the gauges in. Basically the entire bevel had to go. I just kept grinding away until I could press the new gauge in. It's a really tight fit, so no real need to glue anything or bolt anything into place
https://www.rx7club.com/attachment.p...postid=2872302 |
Hmm... no pics! :D
*edit* Beat me to it! Looks great so far! |
Originally posted by jdhuegel1 Hmm... no pics! :D |
|
Next I had to cut out holes in the old covering so that the gauges could poke through. Just circled the area I needed to cut out and ground it out using a cutting bit on the dremel
https://www.rx7club.com/attachment.p...postid=2872346 |
Also had to grind out the old mounting posts and light tunnels from the previous gauges
https://www.rx7club.com/attachment.p...postid=2872360 |
Starting to assemble everything. Got the pieces together and ready to fit into the hood.
https://www.rx7club.com/attachment.p...postid=2872413 |
And finally pictures of the results. I had to grind away a bit of the hood to get the bezels to poke through cleanly. I'm not terribly thrilled with the angle the gauges are mounted at (the angle of the camera doesn't help), they're a little crooked for my tastes , but they are in and as soon as I get the block adapters for the sending units they'll be functional. Also, the silver on the bezel doesn't quite match the chrome ring around the other gauges. :(
https://www.rx7club.com/attachment.p...postid=2872469 |
Here's a night shot. They're MUCH brighter than my other gauges and the color doesn't quite match. :(
And I realized as I got everything back together that one of my bulbs is burned out. So now I'm going to have to rip everything apart again and put some new bulbs in. :hf: For those that are curious I routed the power and sending unit wires through the old light bulb holes, so I didn't have to cut my trace at all. All in all though, not too bad. When I put the new bulbs in I'll see what I can do about correcting the little flaws it has now, but I'm not sure what I can do about the gauge angle as they're seated all the way against the back of the cluster. I'm marginally pleased at this point. I'll just be happy to have functional gauges again. https://www.rx7club.com/attachment.p...postid=2872497 |
Looks pretty good!
|
Very mice work! Could you just paint the bezels black? So they blend in with the hood better? ( Even the way they are it doesn't jump out toooo bad.) I'm glad you posted this as I was wondering about the possibility of doing this. ( Do to the fact that I can't stand the look of A-pillar gauges or the center speaker pods.)
Nice work again! |
Originally posted by BigIslandSevens Very mice work! Could you just paint the bezels black? So they blend in with the hood better? ( Even the way they are it doesn't jump out toooo bad.) I'm glad you posted this as I was wondering about the possibility of doing this. ( Do to the fact that I can't stand the look of A-pillar gauges or the center speaker pods.) Nice work again! |
Originally posted by turbojeff Looks pretty good! |
I agree, looks prett good! Perhaps you are being too discerning? ;)
|
Also could you grind off/cut-out some of the white backing plate to relieve the pressure on the gauges?( Maybe helping in correcting the angle problem.) Or are the mounting tabs for the assembly back there?
|
Originally posted by Brad I agree, looks prett good! Perhaps you are being too discerning? ;) |
Originally posted by BigIslandSevens Also could you grind off/cut-out some of the white backing plate to relieve the pressure on the gauges?( Maybe helping in correcting the angle problem.) Or are the mounting tabs for the assembly back there? The crookedness/angle is actually being determined by the hood, and grinding that down is nervewracking since it's still visible when your're done. |
shoot, forget that gauges, i want more pics from the v8 swap
|
BTW, very nice set-up! |
Originally posted by areXseven Why are you only getting 2psi of Oil Pressure at 900 rpm?? BTW, very nice set-up! |
[QUOTE]Originally posted by wingsfan
but they are in and as soon as I get the block adapters for the sending units they'll be functional. oops- you beat me to your own answer |
Originally posted by twinturboteddy shoot, forget that gauges, i want more pics from the v8 swap |
Originally posted by wingsfan No sender yet. :) The temp reading is the ambient temp under the hood too because neither of them are in the block yet. Good luck with your project! |
Originally posted by areXseven Well that explains that!..., But, what's wrong with your fuel gauge??. It's marking FULL. That HAS to be an error, or is your last name Gates????? :) Good luck with your project! V8 = better mpg :D Seriously though, notice I have 4 miles on it from the gas station. :) |
All times are GMT -5. The time now is 07:33 PM. |
© 2024 MH Sub I, LLC dba Internet Brands