Please help me finishing alarm install
I started taking my car apart a week ago to start my alarm install, I have connected all the wires but I get no input from the alarm. Since part of my engine has been taken apart, I can't completely start my car yet. I got a Viper V791VX and the alarm comes with 10 harnesses.
1. primary harness: 2. secondary harness 3. door lock harness 4. remote start (primary) 5. heavy gauge inline 6. remote start (secondary) 7. led 8. valet 9. antenna 10. shock sensor here is what I have done so far: primary harness: orange - 500mA armed output - DID NOT USE white - light flash output - connected to red/black wire (fuse panel) white/blue - remote start act input - DID NOT USE Black/white - 200mA domelight supervision - DID NOT USE Green - (-)door trigger - connected to Blue/White (-) Blue - mulitplexed input zone 4 - DID NOT USE Violet - (+) Door trigger input zone 3 - DID NOT USE Black - ground to chasis Brown - siren output - connected to red wire of siren Red - constant power - connected to black/green wire red/white - (-)200mA channel 2 validity - DID NOT USE Secondary Harness - DID NOT USE light blue - second unlock ouput white/black - programmable channel 5 output violet/black - porgrammable channel 4 output green/white - factory rearm gray/black - wait to start input light green/black - factory disarm door lock harness: DID NOT USE YET green - (-)Lock (+) unlock output blue - (+) Lock (-) unlock output Remote start primary harness - DID NOT USE pink/white - 200mA (-) programmable IGN2/ACC2 relay turn on yellow - IGN input to alarm pink - (-) 200 mA IGN relay turn on orange - (-)200mA Acces relay turn on purple - (-)200mA Starter relay turn on orange/Black - antiground/ground when armed output blue - (-) 200mA status output Heavy gauge inline connector: purple - (+) output to start (start side) - cut starter cable, connected black/blue wire closest to firewall green - onboard start kill (key side) - other side of starter cable, connected black/blue wire closest to steering wheel red - high current 12V input - connected to black/green wire orange - output to accessory output - connected to blue wire pink - output to primary IGN - connected to black/white wire red - high current 12V input - hooked up to the other red wire on this harness pink/white - output to second IGN - connected to black/yellow wire red/white - high current 12V - DEI connected back to red wire/harness remote start secondary harness: DID NOT USE blue/white - (-)200mA 2nd status/rear defogger gray - Hood pinswitch input brown - brack shutdown wire violet/white - tach input wire black/white - neutral safety switch valet: plugged into brain antenna: plugged into brain LED: plugged into brain shock sensor: plugged to brain siren: red - connected to brown wire on main harness; black wire- grounded to chassis I got some of my information from here: http://www.the12volt.com/installbay/...333&type=Alarm I did not use any resistors/diode, the door lock comes with a relay, but again I have not installed the actuator or ran the wires throgh the door jam. All the fuses are good and connected. Can anyone see I what have done wrong or am missing?? I do not care for the remote start or even the starter kill, really got it for the keyless entry and since this was a discounted price at bestbuys, I bought the unit....only no install from them. I would appreciate any help from anyone, I would like to drive my car around again. |
This should be in the interior/exterior/audio section...
|
I know..... I placed it here because there were more hits to this side of the forum and I REALLY need the help. Sorry about that
|
1 Attachment(s)
u need to run 2 relays to your doorlocks
like this https://www.rx7club.com/attachment.p...d=118364&stc=1 |
Originally Posted by rotoboy661
u need to run 2 relays to your doorlocks
like this Did I wire it up right? The frist step I am trying to take it getting the alarm to work, then the keyless entry...but can't get the first to work |
please don't be shy
|
All times are GMT -5. The time now is 06:03 AM. |
© 2024 MH Sub I, LLC dba Internet Brands