Megan Racing DP Install + Review
Well today I finally got around to installing my Megan Racing down pipe. So far I'm loving it, and I'm glad I decided to get it. On to the review
After reading numerous posts about the DP/MP combo I decided to get it. The combo is much cheaper than most at a whopping 168.63 + 25.25 shipping = 193.88 I ordered the parts from Option Imports. Delivery was quick, packaging descent, and price was good. A 1-10 scale on different aspects of the parts. *Shipping - 10 - delivery was fast and parts were packaged decently *Quality - 7 - nice mandrel bends, welds were ok... I have seen much better. Nice and shiny (not that that really matters) *Install - 4 - welds are in the way of nuts on the flange, required some grinding to get a good fit. Had to remove lower two studs to get pipe on. Difficult to bolt onto cat (flange was angled a bit different than the cat). *Performance - 10 - Butt dyno says big improvement; it was well worth the while of installing it. *Overall I give the part an 8* Specific notes on the install. As mentioned above the welds were in the way on the flange and had to be ground away quite a bit. When trying to bolt it to the cat I had to loosen the catback/cat section and the dp to twist it enough to get the studs into the dp flange. Had to remove the lower two studs to get the dp installed even then it was a big pan in the A$$ to get onto the top studs. Don't get me wrong though besides the few things that caused problems along the way. I am quite satisfied with the product for only 193 shipped I got a dp/mp (donno how the mp fits but I assume its a perfect fit, I held it up to the cat and it looked perfect). Anyone looking for a dp cheaper than most and are willing to take a little more effort than just slipping it on I recommend this dp to you. Sorry so long Mitch P.S. Sorry for no pics, gf had the camera today so I couldnt snap any pics of the install. |
That's good info Mitch. So, if someone wants an inexpensive DP, that doesn't fit perfectly, has bad welds. and has to be ground down to fit, they know where to go ............ just kidding :)
I assume it is mild steel, and not stainless for that price? |
|
Originally posted by adam c That's good info Mitch. So, if someone wants an inexpensive DP, that doesn't fit perfectly, has bad welds. and has to be ground down to fit, they know where to go ............ just kidding :) I assume it is mild steel, and not stainless for that price? Im glad I didn't waste money on a 300 dollar DP for a name brand. ;) |
Here is a pic of the welds, and where it needs to be ground down.
https://www.rx7club.com/attachment.p...postid=2847377 |
Originally posted by Mitch529 Im glad I didn't waste money on a 300 dollar DP for a name brand. ;) Those welds are HORRIBLE quality. I'm glad I paid $300 for a very high quality downpipe from someone who actually designed it. |
Why did you buy a dp/mp combo and only put on the dp?
|
I didn't put on the mp yet because I do not have an ecu to handle it yet.
You mean that you're glad you didn't pay the people who actually designed the part but instead paid a guy who copied the design and has the pipes welded in South Asia? Those welds are HORRIBLE quality. I'm glad I paid $300 for a very high quality down pipe from someone who actually designed it. Mitch |
I just bought a mp off ebay 90 including shipping. I cant see spending any more than that for a pipe with flanges. Thanks for the info on the small amount of grinding as I may have to do that myself (no big deal), did you just use a dremel or something? Thats all I'm sayin here, no flames either way.
|
Originally posted by rdavidsrx7 I just bought a mp off ebay 90 including shipping. I cant see spending any more than that for a pipe with flanges. Thanks for the info on the small amount of grinding as I may have to do that myself (no big deal), did you just use a dremel or something? Thats all I'm sayin here, no flames either way. Mitch |
Originally posted by Mitch529 I didn't put on the mp yet because I do not have an ecu to handle it yet. I posted this review to help people who post about this combo understand what they are getting. And I guarantee it will be the last time, due to prick asses flaming me about it. I never said everyone should buy this combo I said if you’re looking for a cheaper solution then get this combo. Mitch You'll have to excuse Rynberg. He is just a bitter old man :o: Only big names and huge prices please him. Thanks for the write-up. Seems like a no brainer to me for a piece of stainless tubing. |
Originally posted by Mitch529 I posted this review to help people who post about this combo understand what they are getting. And I guarantee it will be the last time, due to prick asses flaming me about it. I never said everyone should buy this combo I said if you’re looking for a cheaper solution then get this combo. Mitch Originally posted by rynberg You mean that you're glad you didn't pay the people who actually designed the part but instead paid a guy who copied the design and has the pipes welded in South Asia? Those welds are HORRIBLE quality. I'm glad I paid $300 for a very high quality downpipe from someone who actually designed it. |
Originally posted by afterburn27 Just ignore the flames and keep the good info coming! :bigthumb: It’s not like there is a tremendous amount of engineering put into this piece... And from what Mitch described, the install doesn't even sound that bad if you don't mind breaking out the dremel. Personally I am quite satisfied that I spent 168 on a piece that only required 10 mins of grinding to get a nut to fit flush on the flange. Mitch |
Originally posted by Fumanchu You'll have to excuse Rynberg. He is just a bitter old man :o: Only big names and huge prices please him. Originally posted by afterburn27 Its not like there is a tremendous amount of engineering put into this piece... It's amazing how people justify things to themselves... |
Originally posted by rynberg When you spend time designing something and somebody else comes along, copies your design, farms out the fabrication to some Asian sweatshop, and undercuts your price by 300%, you might feel a little differently. It's amazing how people justify things to themselves... |
Originally posted by afterburn27 I might feel differently if we were talking about an ecu, or something that a considerable amount of research, testing, and work went into the design. It's simply a downpipe that consists of a pipe with some bends and flanges welded to the ends. |
Originally posted by rynberg paid a guy who copied the design and has the pipes welded in South Asia? Those welds are HORRIBLE quality. I'm glad I paid $300 for a very high quality downpipe from someone who actually designed it. 2) I am a certified wlder and the welds look fine to me. |
Originally posted by tmiked 1) Whoever you bought your pipe from just 'copied' the design of the pre-cat without the catalyst, DUH !! 2) I am a certified wlder and the welds look fine to me. 2) Well, the welds may be functionally fine but they LOOK sloppy -- the guy had to grind the weld down to bolt it up. Have you seen the welds on a Bonez or M2 downpipe? Have you seen the welds on an Apexi or Racing Beat exhaust? Now those are quality welds. |
Originally posted by rynberg 1) Have you ever looked at a downpipe? It is not simply a copy of the OEM pre-cat without the cat. Give me a break. True, it is a straight pipe, LESS design that a pre-cat 2) Well, the welds may be functionally fine but they LOOK sloppy -- the guy had to grind the weld down to bolt it up. Have you seen the welds on a Bonez or M2 downpipe? Have you seen the welds on an Apexi or Racing Beat exhaust? Now those are quality welds. |
This is getting to be a bit much. Rynberg I agree with you that it sucks that someone copied an idea and sells it, but you have to realize that you live in the United States where capitalism thrives. People always copies stuff. How do you think pepsi and coke are so similar. as for buying stuff from sweat shops... well not to be a jerk or offensive, but your probably a hypocrite and dont even know it. have you ever owned nike's? have you ever checked where you clothes were made from? all of us have probably used items from sweat shops at one time in our lives without even knowing it.
just out of curiosity have you ever downloaded a song, movie or any other copy righted material off the internet? enough rambling. lets not bash this product for being a copy. i agree it is of poor quality i had one for a short while but returned it. i'm not gonna grind anything down and reduce the strength of the weld. i'm waiting for my $300.00 M2 DP! |
i have seen apexi stuff and all there stuff has been welded by a robot at production line. I would buy that dp/mp, nice review, hope it works good for you
|
Well I too agree that cutting corners on non quality parts sucks, but the pieces were cheap and of no giant deal if they didn't work so I figured hey why not. And I do have an Apex'I exhaust and the welds are better but you know what? The welds on the dp work just fine.
I never cut corners when modifying I only buy quality parts especially when its something that is a very important part. (ECU, Drivetrain, etc..) but a dam Mandrel bent pipe..... well maybe you can say ooo I have an M2 or Bonez but you also spent 300 dollars and I spent a 3rd of that and go the same dam thing. I'm done with this thread its a waste of time and just a dam pissing contest as to who spent more on a dam pipe. And for the argument of supporting the us business :wtf: after they sold 15 of those pipes they have well compensated for the cost to develop, and produce the dam thing. After that they are just lining their pocket charging us for a over priced piece. as i said before I posted this review to help people who post about this combo understand what they are getting. And I guarantee it will be the last time, due to prick asses flaming me about it. I never said everyone should buy this combo I said if you’re looking for a cheaper solution then get this combo. |
I've presented my opinion, some of you don't share it, that's fine. :)
Mitch529: Upon reflection, I apologize for clogging up your thread with "political" posts rather than discussion on the downpipe. Good luck with it. (although I really hope you weren't the coward who just sent me a rather immature PM under a new forum name...) |
Originally posted by rynberg I've presented my opinion, some of you don't share it, that's fine. :) Mitch529: Upon reflection, I apologize for clogging up your thread with "political" posts rather than discussion on the downpipe. Good luck with it. (although I really hope you weren't the coward who just sent me a rather immature PM under a new forum name...) And I assure you I didn't send that pm I am in no way a coward and will discuss any issue i have with you or anyone else right here for everyone to see. Mitch |
Originally posted by Mitch529 And I assure you I didn't send that pm I am in no way a coward and will discuss any issue i have with you or anyone else right here for everyone to see. Mitch |
All times are GMT -5. The time now is 08:30 AM. |
© 2024 MH Sub I, LLC dba Internet Brands