Going Single & more, a big project has finaly begun... w/lots of pics
5 Attachment(s)
Last years project wasn't delivering much, I rebuilt my twins succesfully, ported the wastegate and converted to full non-seq. mode getting rid of lots of hoses and solenoids, air pump etc..., but I got tired of the lagginess of the non-seq. setup so I decided to go single since my beatifull wife :angel: gave me one of the best Valentines gifts a man can get, a dual ball bearing RX6B kit.
Once I got the kit, I took of the compressor housing and polished it, now since I never polished before the job is not the best ever but is pretty acceptable, see pics below. Since I started polishing I thought some more sh*t under the hood can use the bling-bling factor the turbo got, so I decided ti polish more stuff like: UIM, TB, Alt., FMIC piping, AST, Tork brace etc... Also I'm gonna send all the pulleys to Powder coat to a guy here in the forum (Nappy94), btw I got a UR p/s pulley from optionimports.com for $101.15 which most places sell it for $149.00+ . I also made a FMIC Chiller hoop from a 3/8 brass tube, which is gonna be connected to the winshield washer fluid bottle to spray water to the IC at the same time as the water/alc injection comes online @ 10 psi, so the IC chiller will be connected on the same relay. Within this project I'm throwing in a new 255 walbro fuel pump and relocating the fuel filter on the engine bay for easyer future access, someone tell me if this is bad to do & why ??? OK nuff said, check out some of the pics I already took. --------------------------------- RX6 before polish: https://www.rx7club.com/attachment.p...d=106207&stc=1 https://www.rx7club.com/attachment.p...d=106208&stc=1 After polish: https://www.rx7club.com/attachment.p...d=106209&stc=1 No flash: https://www.rx7club.com/attachment.p...d=106210&stc=1 https://www.rx7club.com/attachment.p...d=106211&stc=1 Lots more to come \/ ... enjoy. :peace: |
lookin good sir
keep it up ;) |
4 Attachment(s)
Originally Posted by rotoboy661
lookin good sir
keep it up ;) ---------------------------------------------- OK, here are some more pics, IC chiller, size 22 X 4-1/4, btw I shaped it all by hand! https://www.rx7club.com/attachment.p...d=106227&stc=1 on this pic you can see the tiny little holes I made on the tube/pipe in criss-cross pattern. https://www.rx7club.com/attachment.p...d=106228&stc=1 Painted w/high heat silver (all I had at the moment) when it chips I'll get some better paint for it. https://www.rx7club.com/attachment.p...d=106229&stc=1 https://www.rx7club.com/attachment.p...d=106230&stc=1 |
4 Attachment(s)
UIM
I'm not to happy w/the uim how it came out and I'm not going to do it again, took me 2 damn days to do it, my neck was stiff for 3 days after... :stick: https://www.rx7club.com/attachment.p...d=106233&stc=1 https://www.rx7club.com/attachment.p...d=106234&stc=1 https://www.rx7club.com/attachment.p...d=106235&stc=1 https://www.rx7club.com/attachment.p...d=106236&stc=1 |
What size Co2 bottle are you using and how long does it last?
|
Originally Posted by 1987RX7guy
What size Co2 bottle are you using and how long does it last?
|
5 Attachment(s)
AST
before polish: https://www.rx7club.com/attachment.p...d=106239&stc=1 https://www.rx7club.com/attachment.p...d=106240&stc=1 After polish: https://www.rx7club.com/attachment.p...d=106241&stc=1 https://www.rx7club.com/attachment.p...d=106242&stc=1 https://www.rx7club.com/attachment.p...d=106243&stc=1 |
sweet what brand water injection are you running?
|
Originally Posted by 1987RX7guy
sweet what brand water injection are you running?
|
Originally Posted by TwinTurbo93
No brand name, I custom made it w/new parts from all over...
cool |
I tried the water thing man, it doesnt work that graet. It makes a big mess tho. Use CO2;)
Good job on the polishing. I tried polishing for my first time whei a 6" pipe. It took forever, and I dont want to do it again. You have alot of patience polishing the UIM:bigthumb: |
4 Attachment(s)
Originally Posted by 1987RX7guy
cool
------------------------ RX6's Cross over/IC pipe, wet 600 grit https://www.rx7club.com/attachment.p...d=106248&stc=1 https://www.rx7club.com/attachment.p...d=106249&stc=1 Polished: https://www.rx7club.com/attachment.p...d=106250&stc=1 https://www.rx7club.com/attachment.p...d=106251&stc=1 |
Originally Posted by 1sicsol
I tried the water thing man, it doesnt work that graet. It makes a big mess tho. Use CO2;)
Good job on the polishing. I tried polishing for my first time whei a 6" pipe. It took forever, and I dont want to do it again. You have alot of patience polishing the UIM:bigthumb: Thanks, polishing is a pain the ass, once I'm done with it, will never polish again. :D Now I'm in the process of doing the 2 hardest parts, alt & TB :eek: :peace: |
1 Attachment(s)
TB now :puke:
https://www.rx7club.com/attachment.p...d=106254&stc=1 Who knows how it's gonna look after! :scratch: That's all the pics I got for now, more to come soon . :peace: |
|
Originally Posted by hondasr4kids
Nice book PERVERT ;) J/K
|
Just for shits and giggles, do you mind showing how the airpump might fit with that single turbo kit. I'm curious to see.
|
looks great, post some final pics when it's all in the engine bay
|
Originally Posted by TwinTurbo93
Hahahhaha, btw that book was signed for me by the MAN himself, Hugh Hefner :D .
|
Originally Posted by FDeez
Just for shits and giggles, do you mind showing how the airpump might fit with that single turbo kit. I'm curious to see.
Originally Posted by stokedxiv
looks great, post some final pics when it's all in the engine bay
Originally Posted by HDP
And you are using it to lay parts on? :p:
:peace: |
Looking good!
|
Originally Posted by REXDEX
Looking good!
|
4 Attachment(s)
OK, I just did the greddy elbow also, this one didn't need sanding, Thank GOD. :bowdown:
https://www.rx7club.com/attachment.p...d=106301&stc=1 https://www.rx7club.com/attachment.p...d=106302&stc=1 https://www.rx7club.com/attachment.p...d=106303&stc=1 No Flash, I kinda like these without flash, doesn't show all the imperfections :hah: https://www.rx7club.com/attachment.p...d=106304&stc=1 |
damn john, looks geat!!
cant wait to see the final look in person :) |
Hey, does this mean youre going to have to change your username on here??? JK...
|
All times are GMT -5. The time now is 11:10 PM. |
© 2024 MH Sub I, LLC dba Internet Brands