RX7Club.com - Mazda RX7 Forum

RX7Club.com - Mazda RX7 Forum (https://www.rx7club.com/)
-   3rd Generation Specific (1993-2002) (https://www.rx7club.com/3rd-generation-specific-1993-2002-16/)
-   -   Exhaust clanking / what's this bar under the car (https://www.rx7club.com/3rd-generation-specific-1993-2002-16/exhaust-clanking-whats-bar-under-car-875739/)

red_dragon 11-29-09 04:09 AM

Exhaust clanking / what's this bar under the car
 
1 Attachment(s)
There's the support bar of some sort under the car that my exhaust is clanking against.

1. What's the bar do? I'm guessing it's a body brace of sorts?
2. Is it wise to put something between the bar and the exhaust pipe? Maybe a piece of high temp silicone? Or something?
3. If that's not a good idea, what would you guys do to fix this?

Sgtblue 11-29-09 06:36 AM

Yes, it's a crossmember.
It would be better to find out why the exhaust and brace are making contact. Have you checked the hangers?

alexdimen 11-29-09 01:01 PM

No offense if they're your welds... but judging from just that one in the picture the exhaust system is rigged and probably can't be aligned properly to avoid the xmember.

badddrx7 11-29-09 04:58 PM

The proper fix, since you have a 3" exhaust now is to make up a new crossbrace that will allow the pipe to clear. I can make you up one for $150 shipped or you do it for the price of a 3/16" bar and fab work.



Later

brad89au 11-30-09 08:01 AM

i have a $1500AUD knightsports midsection and even it hits on the crossbrace. i have made up some spacers for mine at the moment but it does scrub on the ground and i dont like it, tom, is there a link to a thread with some pictures of your product?

Thanks;
Brad.

red_dragon 11-30-09 01:28 PM


Originally Posted by brad89au (Post 9650029)
i have a $1500AUD knightsports midsection and even it hits on the crossbrace. i have made up some spacers for mine at the moment but it does scrub on the ground and i dont like it, tom, is there a link to a thread with some pictures of your product?

Thanks;
Brad.

Pics would be cool. Also, brad what material did you use for the spacer?

Sgtblue 11-30-09 02:43 PM


Originally Posted by badddrx7 (Post 9648917)
The proper fix, since you have a 3" exhaust now is to make up a new crossbrace that will allow the pipe to clear.

Just for clarification, is it some of the exhaust systems that won't clear? Because my 3 inch system clears fine.

badddrx7 11-30-09 05:29 PM

With the proper bends a 3" aftermarket exhaust will barely clear the rear crossbrace, but most that I have seen won't. The hangers allow the "clanging"

what I am talking about it the front part of my differential brace as you see here in the pics.



For some reason the pics will not upload. Send me an e-mail and I'll send them to you. Maybe you can upload them. E-mail, not a PM.

blueyes01@roadrunner.com


later

gracer7-rx7 11-30-09 06:54 PM


Originally Posted by Sgtblue (Post 9650657)
Just for clarification, is it some of the exhaust systems that won't clear? Because my 3 inch system clears fine.

So does mine

brad89au 12-04-09 04:47 AM


Originally Posted by red_dragon (Post 9650523)
Pics would be cool. Also, brad what material did you use for the spacer?

just some 12mm thick hard plastic sheetin i had lying around. i find its far too low tho as the bolts scrape on the driveway which isnt that steep at all.

Brad.

rash_rvg 12-04-09 06:25 AM


Originally Posted by gracer7-rx7 (Post 9651118)
So does mine

And so does mine.

catch-22 12-04-09 01:24 PM

Like someone else said check your hangars. There made of rubber and over the years they can start to sag and put a lot of play in the exhaust system.


All times are GMT -5. The time now is 11:14 AM.


© 2024 MH Sub I, LLC dba Internet Brands