anyone use this style of gauge holder?
I am exploring options for mounting a single multigauge. I hate A-Pillar gauges and do not want to look down toward a DIN panel. I also have a single gauge so I wouldn't want to run a tripower or prosport pod in the center speaker.
I am thinking of using this with double sided tape for either the center speaker or on top of the steering column...does anyone have any pics of how this would look? Auto Gauge Ring Mount (2 1/16" 52mm) | Wideband O2 OBD2 Sensor |
To each his own, but IMO that looks pretty cheesy. And doubt double-sided tape would hold long. Pettit and Amemiya offer a single pod for the column. And I know you don’t like them but FWIW a single A-pillar pod can be made to sit low and not affect visibility....IMO a better option than what you’re considering.
|
I have used those in the past on my FC, Greddy used to (I don't think they make them anymore, could be wrong) make gauge holders like that. They actually stick very well (they have the double-sided tape in the package) and the "fingers" of the base can be bent to accommodate a curve in the dash.
You do need some loom or something to put over the wiring so it's neat looking. It does have an industrial look to it and some gauges (cough Autometer cough) that have bobo looking backs will be meh. That said, the Pettit steering column pod does sink the gauge down into the pod a little and angle it, with that you would have better visibility of the tach. The Pettit pod is really nice, it looks super clean and fits well. Dale |
That would look awful. Dont do it. Best bet is to get a steering column pod like Dale and Jim have mentioned.
|
Agreed. That is cheesy... Here is link to the pod that everyone has mentioned:
RX7 Column Mount Gauge Pod https://www.rx7club.com/attachments/...1-16.05.17.jpg https://www.rx7club.com/attachments/...1-16.05.37.jpg |
|
1 Attachment(s)
I did this for my water/meth failsafe gauge.Screwed down with small bolt with nut and washers.
|
Is the pettit one different from the one offered at rx7store? I would only want to use it if the material matches the rest of the dash pieces and steering column well.
|
^^ dude come on. Pick up the phone and call them...
|
FYI the Pettit pod is very similar in style to the RE-Amemiya pod, you see those every now and again on Ebay. But, the Japanese pods are made for RHD cars, and the turn signal/wiper stalks are reversed. In other words it will bolt up but you won't be able to properly use the stalks, they will hit the pod. Way easier to just get the Pettit one.
Dale |
Originally Posted by mkiv98
(Post 12233537)
Is the pettit one different from the one offered at rx7store? I would only want to use it if the material matches the rest of the dash pieces and steering column well.
|
That Auto Meter abomination is friggin' hideous. I mean...seriously.
|
Originally Posted by Sgtblue
(Post 12233703)
Yeah...because that Auto gauge ring with double-sided tape that you’re thinking about matches so well and no one will know that it isn't really stock.
|
And is that an engine coolant temperature gauge on the A-pillar? |
The gauges are just old Defi ‘D’ series gauges. They’re discontinued now but their font, needle color, black face and back lighting do match the stock dash pretty well. IIRC they make some others now that also look good. And yeah, it’s a coolant temp gauge. It’s reasonably accurate but I wish it had an alarm. The pod was trimmed down a bit so it would sit lower and has my green and red LED lights for WI.
|
Originally Posted by Sgtblue
(Post 12236697)
The gauges are just old Defi ‘D’ series gauges. They’re discontinued now but their font, needle color, black face and back lighting do match the stock dash pretty well. IIRC they make some others now that also look good. And yeah, it’s a coolant temp gauge. It’s reasonably accurate but I wish it had an alarm. The pod was trimmed down a bit so it would sit lower and has my green and red LED lights for WI.
|
All times are GMT -5. The time now is 07:11 PM. |
© 2024 MH Sub I, LLC dba Internet Brands