RX7Club.com - Mazda RX7 Forum

RX7Club.com - Mazda RX7 Forum (https://www.rx7club.com/)
-   2nd Generation Specific (1986-1992) (https://www.rx7club.com/2nd-generation-specific-1986-1992-17/)
-   -   thump in transmission when changing gears (https://www.rx7club.com/2nd-generation-specific-1986-1992-17/thump-transmission-when-changing-gears-100550/)

swrx7 07-28-02 11:37 PM

thump in transmission when changing gears
 
here is my problem....

when i shift gears i get a large thump form somewhere in the rear of the car. i have had this problem once before and it was the u-joints...but not this time. i cant pinpoint the problem but it is very annoying and feels like the transmission is gonna fall out. i have checked the driveshaft and it appears to be fine. i have also checked for any play in the rear end but cant find anything. anyone got any suggestions???
(this is an 88 se 210,000 miles)

Spraintz 07-28-02 11:45 PM

Very similar problem that happend to me in a 1987 Base. There is mount that keeps the diff. housing connected to the rear subframe, it may have broken.

Hope that helps

ZachSpazz 07-28-02 11:46 PM

It's most likely your front differential bushing. These things are almost always goofed up on our cars and I imagine your car is no exception.

swrx7 07-28-02 11:49 PM

thanx for the info..will check in the morning

GLHS 07-29-02 08:11 AM

you have a broken diff mount.

you need to have it welded back on.

HAILERS 07-29-02 08:53 AM

This jpg: https://www.rx7club.com/forum/attach...&postid=880442

von 07-29-02 09:05 AM

same here. ITs the diff mounts. Probly the front. You can change it yourself.

christi 07-29-02 01:22 PM

I have the same problem, but I'm missing some diff. mounts....

akageals 07-29-02 01:34 PM

Just replaced the front diff. mount on my car. push up and down on the "nose" (where the drive shaft bolts up) of the diff. . If it moves, the mount is broken.

Todd

Whislr 07-31-02 12:28 AM

I can do one better, here is a pic of what I had to deal with this last weekend. This is what happens when the diff mount doesnt get tightened, and also additional pony's will cause this. I had to manufacture an 1/8 inch slotted plate to weld in so the nuts would bear all around. Sorry no pics of the plate but here is a pic of the tab that broke off. It wasnt to bad of a job getting the sub frame out, dont be discouraged.....

swrx7 07-31-02 01:14 AM

much thanx every1 for the info and pics ......havent had a chance to check yet but will have access to a lift this weekend. where is the best place to buy a new diff. mount? i ve been looking through mazdatrix but the seem a lil expensive aon some things.

Whislr 07-31-02 12:00 PM

check your pm swrx7

UniqueTII 07-31-02 12:05 PM

The stock ones suck, so if you're going to buy one, try and get a stronger one.

swrx7 08-01-02 02:47 AM

thanx whislr

Scott 89t2 08-01-02 02:53 AM

www.mazdamotorsports.com sells theirs for $63. stronger then stock. it's not listed just call and tell them you want the front diff mount for your year/model (all 2nd gens the same).

Pyrocloud 05-18-03 10:41 PM

bump

SureShot 05-19-03 08:27 AM

With a clunk thunk here,
And a tink clink there,
Old McDonald had a 7,
E I E I O..


All times are GMT -5. The time now is 12:58 PM.


© 2024 MH Sub I, LLC dba Internet Brands