radio wires cut on 88gxl, can anyone help with wich ones are wich
i hate when people do this cause they are to cheap to buy an 5 dollar harness so can someone please tell me wich wires are wich
|
look in the faq at the top of the forum. this has been covered a million times :uh:
/thread |
|
i have and any word i type in says no matchs, could you find it and paste the link for me please?
|
i did :)
|
that links not working
|
never mind, i had pop ups blocked lol
|
these fools guted these wires bad, even on the passenger side, that wire clip that plugs in the the speaker stuff is cut, im gonna have to wire this whole car over!!!!
|
if the 6 pin clip on the passenger side is cut would that cause the the deck not to work when i wire it up, because that clip has the same color wires used for power ect, how would i go about wirering the deck manually i guess u could say to wire it with out using the existing wires
|
probably blown fuses
|
well i checked the room fuse and the radio fuse, both blown, i put a 10 amp in the radio one and still no juice, its litteraly like all the wires are dead, would the room fuse have anything to do with it?
|
Audio is 20A
|
http://forum.teamfc3s.org/attachment...6&d=1048910917
Audio fuse and room fuse, power the radio |
i know but i dont have one lol, that could be an issue could it?
ok this is hat the deck says for the wires red/ switched power ignition lead black/ ground lead blue/white= remote turn on blue/ power ant yellow/battery lead now can sombody tell me witch colors go to the wires in the car |
ok so if i get both good fuses in those i should get live wires right?
|
ok so if i get both good fuses in those i should get live wires right?
|
Originally Posted by gotgrip666
i know but i dont have one lol, that could be an issue could it?
ok this is hat the deck says for the wires red/ switched power ignition lead black/ ground lead blue/white= remote turn on blue/ power ant yellow/battery lead now can sombody tell me witch colors go to the wires in the car The radio wire info is found in the FAQ for FC sticky thread found at the top of this section. |
no i am reffering to the deck its self, not the car wires, like the deck says yellow battery lead, but the red says switched power so im just want to make sure so i know im doing nothing wrong
|
Originally Posted by FAQ for FC
What are the wire colors for adding aftermarket radio
LTBlue/Red= 12v+ LtBlue/White= + Accessory/Switched LtBlue/Yellow= - power ant trigger Red/Black= + Lumination White=Factory Amp Turn on Ground to the body, use the 10mm bolt behind the center console front drivers access panel. Do not use the Red/Black as ground it will damage the interior light circuit and dimmer in the car Front Speakers (maximum of a 15 watt peak from the radio): LtGreen/Red= Left LtGreen/Black= Left LtGreen= Right LtGreen/Yellow=Right Rear Speakers (if applicable, if you have the amplified rear speakers again the Maximum of 15 watts peak is all the stock speaker amp input can handle): Brown= Left rear Brown/White= Left Rear LtBlue= Right Rear LtBlue/Orange=Right Rear Note: as mentioned above the power antenna's trigger is ground (or - ). With all aftermarket radio's antenna output as 12 volts positive (+). To make a stock power antenna work you need a relay wired like this: https://www.rx7club.com/forum/attach...postid=1853497 |
ok i went outside put 2 fuses in, i connected the yellow wire to the blue and red wire and i had the blck wire touching the 10 mm bolt on the side, now the deck should have turned on right? it seemed as there was no juice but as i pushed the wires in getting ready to come back in side they sparked and lew out the room and radio fuse, now am i missing somthing or should the deck have turned on with just the yellow wire connected to the blue and red wire plus the ground hooked up?
|
I don't think you are getting it.
You need the constant power and switched power and a ground for the radio to power on. and your bump has been deleted. Bumps are forbidden in the 2nd gen technical section and frankly are rude anywhere if posted within 48 hours. SO Again: LTBlue/Red= 12v+ LtBlue/White= + Accessory/Switched LtBlue/Yellow= - power ant trigger Red/Black= + Lumination White=Factory Amp Turn on Ground to the body, use the 10mm bolt behind the center console front drivers access panel. Do not use the Red/Black as ground it will damage the interior light circuit and dimmer in the car. So Yellow of the aftermarket radio goes to the Mazda blue/red (with a real connector- not with the wires being exposed) The red of the aftermarket radio would go to the Mazda Blue/White Black of the aftermarket radio to Ground. Blue/White of the aftermarket radio to the Mazda White wire Blue of the aftermarket radio to the aftermarket power antenna relay you install. . |
ok thanks that is mutch more clear to me, now i have one issue with the mazda blue/white wire, it is cut from the connector clip that clips to the passenger side speaker if that is cut from there, does it not work in the dash part where you wire up the actual wire to the radio? and once again thank you for making the wirering clear for me :)
Originally Posted by Icemark
I don't think you are getting it.
You need the constant power and switched power and a ground for the radio to power on. and your bump has been deleted. Bumps are forbidden in the 2nd gen technical section and frankly are rude anywhere if posted within 48 hours. SO Again: LTBlue/Red= 12v+ LtBlue/White= + Accessory/Switched LtBlue/Yellow= - power ant trigger Red/Black= + Lumination White=Factory Amp Turn on Ground to the body, use the 10mm bolt behind the center console front drivers access panel. Do not use the Red/Black as ground it will damage the interior light circuit and dimmer in the car. So Yellow of the aftermarket radio goes to the Mazda blue/red (with a real connector- not with the wires being exposed) The red of the aftermarket radio would go to the Mazda Blue/White Black of the aftermarket radio to Ground. Blue/White of the aftermarket radio to the Mazda White wire Blue of the aftermarket radio to the aftermarket power antenna relay you install. . |
Originally Posted by gotgrip666
ok thanks that is mutch more clear to me, now i have one issue with the mazda blue/white wire, it is cut from the connector clip that clips to the passenger side speaker if that is cut from there, does it not work in the dash part where you wire up the actual wire to the radio? and once again thank you for making the wirering clear for me :)
I don't know how much clearer the wiring could be. It has been posted mutiple times in this very thread well alone countless others and the FAQ for FC sticky thread. I must suggest that if you don't grasp the rather very simple radio wiring that you probably should be taking the car to a professional car stereo installer with the wiring information from this board. Given the difficulty here, you may be in over your head owning a RX-7 and perhaps another car is a better choice as well. |
alright im about to give up, i put new fuses in today and now the door and hatch light come on when i try to turn on the interior light, i think im just gonna sell this thing and finish working on my 10 second talon
|
1. Tape off your wires in the dash you have wires touching eachother.
2. You have blown fuses more than once, you may have fried your deck |
All times are GMT -5. The time now is 01:19 PM. |
© 2024 MH Sub I, LLC dba Internet Brands