No digital clock
 

Let me keep this simple.

I turned the car on one morning and... no clock, just a blank screen. Absolutely no clue what could have provoked it.

All the other warning lights work fine, no other elections problems to report.


Has the clock just given up or should I look into some fuses/wiring?

Bad solder joints in the warning cluster.
Very common.

you only need to know time in a Delorean.

theres a fuse just for that clock

First thing you ALWAYS check when a fused electrical circuit isn't working.. THE FUSE :)

If the fuse is good, go ahead and take the clock out and check for bad solder joints internally. If that is the problem, it is a pretty straight forward fix.:

Cold Solder points fix for the Clock/Idiot light
Start by placing the blade of a flathead screwdriver under the front lip of the plastic trim piece that is in front of the clock/idiot light unit. Pry it up and you will see two screws that hold the assembly in place, one on each side of the unit. Remove these screws and pull the clock unit out. The wires are tight but some slack can be pulled out from the inside of the dash. Unhook the clock/idiot light module. Remove a few screws from the back of the unit and carefully check and resolder all the solder connections on the socket for the plug. Resolder other stuff if you are feeling adventurous. Installation consists of plugging the unit back into the wiring harness, screwing it back in, and snapping the trim piece back over the unit. It is short and sweet. One important note, if you decide to resolder ALL of the solder points in the unit, be careful, there are a number of delicate components that can be killed with great ease by overheating, especially under that little black plastic thing.

lol my clock constantly flickers and goes on/off when i'm driving. i'll be doing this as well in the near future even though i have an aftermarket radio with a clock on it haha. thanks

+1, but with the below amendment. Also, not changing the content I broke up funkjaw's instructions to a step by step thing.

*Before you do anything, identify the two pins that provide hot/+ and ground/- from the online FSM. This is the only circuit you need to be concerned with. My opinion, don't mess with anything that is already working properly, aka "If it ain't broke, don't fix it". That way you don't have to worry about messing those things up in the process per funkjaw's warning.

Follow the circuit that runs from those two pins and melt/re-solder each solder bump connection point with a HOT soldering iron so you won't need to hold the iron to the solder point very long as funkjaw warned. Add additional solder as necessary to insure a good joint.

The first thing I did was look at the fuse box and didn't see anything that specifically related to the clock. The only thing that doesn't work is the clock and I figured a blown fuse would cause multiple problems. Am I wrong?


It seems the more common thing is a bad solder joint so I'll look into that soon.

7.5 amp Room fuse.

Maybe you're just out of time?

Oy vey.

or if you're not savvy with doing it yourself i repair the joints for $20 plus return shipping.

Yup try resoldering, had the same issue with mine.

i believ the same fuse runs the power mirrors, do they work? if not check the fuse

i need to re solder mine i have some dim lights that stay dimmly lit, anyone have a pic of what to exactley solder?

follow the connector on the backside of the cluster, on the other side of that connector is where they solder to the board and have a tendency to crack. resolder all of the main pins from that connector to cure any randomness with the cluster.

I checked the Room fuse and it doesn't appear to be blown. However, also I checked to see if my power mirrors work, and they do not.

So I replaced the Room fuse with Meter fuse (also 7.5 amp), and the same result.


So what does this tell me?

The Power Mirrors are powered by the 10 amp Cigar fuse which is one of the two fuses to the clock besides the Room fuse so check the Cigar fuse.

A pic would be giving you the fish. To learn how to fish, I repeat:

*Before you do anything, identify the two pins that provide hot/+ and ground/- from the online FSM. This is the only circuit you need to be concerned with. My opinion, don't mess with anything that is already working properly, aka "If it ain't broke, don't fix it". That way you don't have to worry about messing those things up in the process per funkjaw's warning.

Follow the circuit that runs from those two pins and melt/re-solder each solder bump connection point with a HOT soldering iron so you won't need to hold the iron to the solder point very long as funkjaw warned. Add additional solder as necessary to insure a good joint. <!-- / message -->
<!-- sig -->__________________

Yes yes and yes! Cigar fuse was blown. Replaced fuse with a 10amp from the spare slot and we are back in business.

Thank you

(my friend recently tried to run a gps off the cigar lighter, that must've been it, all makes sense now)

I apologize for being wrong.
Sure am glad I didn't get to my second recommendation which was "replace the apex seals".
That would have been very embarrassing.

analog clock
 

the analog clock on my 1980 runs real slow. any thoughts?

6 year thread necro and wrong section.

you're batting a thousand.

This purely shows that the RX7 Club is now more lenient and has new and improved rules.
Yes it is the start of the apocalypse.. Zombie threads can come alive and exist amongst the living...Mwuahhahhaa!..
If your car won't run OR if your cigarette Lighter won't work so you can light the wick on that can of gas to throw at the Zombie....Call RotaryEvolution!.
He can fix it with a combo Running car that shoots Fireballs!...lol!

*this concludes the Emergency Broadcast of Stupid material..we now go back to the Insanity of Rx7 Moderation..!

PS: time stands Still in an Rx7 so who the fark cares about a clock!

lol, well the older first gen had quartz mechanical hand clocks, so his is probably either toast or has drag/slop in the gears. the later first gens had a digital quartz clock.

i couldn't tell ya if there is a fix for the mechanical version, except maybe with a hammer.