RX7Club.com - Mazda RX7 Forum

RX7Club.com - Mazda RX7 Forum (https://www.rx7club.com/)
-   2nd Generation Specific (1986-1992) (https://www.rx7club.com/2nd-generation-specific-1986-1992-17/)
-   -   new eng will not start plz help mad gas (https://www.rx7club.com/2nd-generation-specific-1986-1992-17/new-eng-will-not-start-plz-help-mad-gas-536074/)

ticalll 05-01-06 07:43 PM

car will not start new engine plz help
 
i got a 1987 non turbo rx7 i just put a new engine in and it will not start its got no emissions on it its seems to be geting mad gas it did start 1 time but the fuel pump fuse was out plz help I GOT ALL THIS ON THE CAR BLOCK OF PLZ HELP F PLATES PINAPPIE RACING PORT SLEEVES TURBO OIL PUMP DUAL BELT ALTERNATOR PULLY AND MAINE PULLY WALBRO 255 FUEL PUMP INTAKE HEADERS

J-Rat 05-01-06 07:44 PM

F L O O D E D!

NeCr0mStR 05-01-06 07:52 PM

indeed

calrx7 05-01-06 08:23 PM

yep, definently flooded

ticalll 05-02-06 04:02 PM

new eng will not start plz help mad gas
 
new eng will not start plz help mad gas

plz help i got a 1987 non turbo rx7 with a new eng engine it will not start and i dont know why it did start 1 time for like 5 sec but the fuel pump FUSE WAS OUT its geting mad gas the car has no emissions its geting spark plz help

classicauto 05-02-06 04:32 PM

a little more info would be sweet, like what is this "new" engine, a rebuild? a used Jspec?

define "mad gas"....

it sounds to me though like its just severly flooded....barring more info on the car - check the FAQ for the de-flooding procedure

J-Rat 05-02-06 04:39 PM

He posted this yesterday, and we all told him it was flooded. Guess he didnt get the hint.

ITS FLOODED!

J-Rat 05-02-06 04:41 PM

My car doesn't start
Remember when starting a fuel injected car you should never pump or press the accellerator pedal, but if it won't start it is probably flooded, Hold the accelerator pedal all the way down while cranking, do not pump the pedal. If it still doesn't start after a few tries, Then remove the EGI fuse and crank a couple more times, then re-install the fuse and try starting again. If then the car still fails to start it then you need to remove and clean the spark plugs, put in a teaspoon of ATF into the lower sparkplug holes, re-install the spark plugs and try again. Make sure you change your oil after you have started and run the car ASAP.

Sideways7 05-02-06 05:01 PM


Originally Posted by classicauto
define "mad gas"....

I always thought "mad gas" was something you got after eating Mexican food...

ticalll 05-03-06 04:55 PM

new eng will not start plz help mad gas
 
new eng will not start plz help mad gas

plz help i got a 1987 non turbo rx7 with a new eng engine it will not start and i dont know why it did start 1 time for like 5 sec but the fuel pump was not on its geting mad gas the car has no emissions its geting spark plz help

90WhiteVrt 05-03-06 05:21 PM

New engines are generally hard to start. Do a search and i'm sure you'll find several threads about situations similar to yours.

ticalll 05-03-06 05:23 PM

i have been looking but cant find

ticalll 05-03-06 06:25 PM

i know this but why flooded

ticalll 05-03-06 06:28 PM

i know its FLOODED but why its a rebulid plz help

91verty 05-03-06 06:28 PM

just take it easy and drain the fuel outta the chambers by cranking it a few times with the plugs out. This is very common. MAke sure to remove the egi fuse in the engine bay. This is probably gonna happen several times, so be prepared. Also might wanna check the psi on your FP.

swbooking 05-03-06 06:31 PM


Originally Posted by Sideways7
I always thought "mad gas" was something you got after eating Mexican food...

Haha NOICE! or cheese or broccoli hahah

J-Rat 05-03-06 06:44 PM


Originally Posted by ticalll
i know its FLOODED but why its a rebulid plz help

Because rebuilds tend to have lower compression..

J-Rat 05-03-06 06:45 PM

Dude, are three seperate threads necessary?

ticalll 05-03-06 06:47 PM

its got new spark plugs new oil lines block off plates Atkins' Thermal Pellet Atkins 2mm Solid Corner Seal Atkins 93-95 Corner Seal Spring pinapple racing ports sleeves turbo oil pump racing beat dual belt alternator pully and maine pully quick release steering wheel and hub cross floor bar lower arm bar brace solid aluminum engine mounts carbon hood pins intake headers 8mm wires all new inj grommets and o rings ss oil lines ss clutch line and all new red vacuum hose all new gaskets cant get it to run plz help

J-Rat 05-03-06 06:50 PM

Remove the Quick Release Steering wheel and the carbon hood pins! They are the source of ALL your problems!!!

Seriously.. Your car is flooded. Did you read up on how to deflood your car yet?

J-Rat 05-03-06 06:54 PM

http://www.rx7.com/techarticles_unfloodFC.html

here ya go..

ticalll 05-03-06 06:56 PM

i know its flooded i am trying all that shit it will not start it its geting to much gas but why

J-Rat 05-03-06 06:58 PM

Its not getting too much gas unless an injector is stuck wide open (which I highly doubt). You might need to just unplug the fuel pump for a while.. If you are still getting gas while unflooding, then you are doing it wrong.

Icemark 05-03-06 07:04 PM

Multiple threads on same subject by the same originator merged.

ticalll only start one thread on the same subject

ticalll 05-03-06 07:10 PM

sorry about that i am new and i dont take the fuse out i take the wier off the fuel pump from back i m going to try the ATF thing


All times are GMT -5. The time now is 12:20 PM.


© 2024 MH Sub I, LLC dba Internet Brands