RX7Club.com - Mazda RX7 Forum

RX7Club.com - Mazda RX7 Forum (https://www.rx7club.com/)
-   2nd Generation Specific (1986-1992) (https://www.rx7club.com/2nd-generation-specific-1986-1992-17/)
-   -   Engine pull writeups?? (https://www.rx7club.com/2nd-generation-specific-1986-1992-17/engine-pull-writeups-47620/)

dcamcoTII Jan 23, 2002 11:07 AM

Engine pull writeups??
 
Does anyone know where I can find a writeup on pulling the motor, or at least disconnecting te motor from the transmission?

FPrep2ndGenRX7 Jan 23, 2002 06:49 PM

Haynes Manual
Chiltons
Factory Service Manual

Scott 89t2 Jan 23, 2002 06:53 PM

the tranny is the easy part :) disconnect battery, unplug starter, undo 2 starter bolts, un do tranny bolts :)

get the FSM off of www.fc3s.org

'Vert in Vegas Jan 23, 2002 07:13 PM

A few more items
 
For the tranny:
also the speedo cable and driveshaft.

fc3s.org Jan 23, 2002 07:15 PM

Yeah it is super easy to remove a motor from an FC. Make sure you either drain the stuff out of the block before pulling it in the garage, or have a few buckets for oil and water :D The FSM does a good job of describing it. Next time I pull mine (quite often actually) I'll take some notes and pics :D

Do a search in here, and you also might find something.

Scott 89t2 Jan 23, 2002 07:17 PM

Re: A few more items
 

Originally posted by 'Vert in Vegas
For the tranny:
also the speedo cable and driveshaft.

he's not removing the tranny, he's pulling the engine :p:

niner Jan 23, 2002 07:44 PM

one piece of advice... REMOVE HARNESS THROUGH FIREWALL FIRST
it makes it a whole lot easier, a lot of people(including myself, the 1st time) take the intake runners and throttle body etc. off to disconnect the harness. just pull it through the firewall
other than that, they are pretty easy

dcamcoTII Jan 23, 2002 08:30 PM

when you say pull the harness through the firewall, you mean to the engine side right?? And is this the 2 small plugs?? From what I understand there are 3, 1 large and 2 small, and the 2 go to the motor. Please correct me if I am wrong.

peejay Jan 23, 2002 08:37 PM

how the heck do you get the top bellhousing bolts off without pulling the intake manifold off?

niner Jan 23, 2002 09:41 PM


Originally posted by dcamcoTII
when you say pull the harness through the firewall, you mean to the engine side right?? And is this the 2 small plugs?? From what I understand there are 3, 1 large and 2 small, and the 2 go to the motor. Please correct me if I am wrong.
i did it to my 87TII a few days ago. you have to disconnect like 5 or so connectors from inside of the car to the ecu
you have to do a bit of work-pull carpet and kickplate and find which connectors to unplug, but its worth it
its a little difficult to work them through the firewall also

niner Jan 23, 2002 09:43 PM


Originally posted by peejay
how the heck do you get the top bellhousing bolts off without pulling the intake manifold off?
easy, either w/ a long extension from underneath or w/ a long wrench from the top. i did have to take off the intercooler on the turbo motor to get em though

dcamcoTII Jan 23, 2002 09:49 PM

Thanks for the replies

niner Jan 23, 2002 09:55 PM

good luck!

dcamcoTII Jan 23, 2002 09:57 PM

Thanks for the answer, I just found out so I edited the post to make myself sound more edumacated ;)

niner Jan 23, 2002 09:59 PM

yeah, i tried to destroy my evidence also:)


All times are GMT -5. The time now is 06:44 AM.


© 2026 MH Sub I, LLC dba Internet Brands