87 TII T04 Hybrid Dyno
Here is the turbo, Its a rebuilt S5/T04b V-Trim Compressor....
I dynoed a Peak Hp of 296.5 and tq was 249.01 @13psi not too bad eh.. that was with a minor exhaust leak it was 72 degrees and I was Using compressed air to freeze My IC... Any comments welcome:D |
I hate you...:)
|
I can post my Safc-II settings if it would be useful to anyone... basically Im maxing out my 680cc secondaries
mostly + after 5k Rpm |
What kind Of 1/4 times should my setup be capable of guys? 12's mabie? :D
"Dont hate me cause my turbos beautiful ;) " |
You're gonna blow the engine with those AFR's... shoot for below 12:1
|
Yea im keepin the boost around 12 psi until I can get my hands on some---850's to replace my 680's........ I called Injector.com and they claimed a mass national shortage of 850cc injectors??? :confused:
|
imflammable, is that turbo stock other than the compressor wheel, or did you use a t04b housing as well?
|
You still running the TMIC?
Sweet numbers! |
Wow, that's some big numbers from a V-trim.
Congrads! -Ted |
I'm going to keep asking this in every hybrid thread I see. Turbine wheel stock/clipped?
Boost response? |
nice numbers. get your afrs down.
what are your complete mods? |
i'd also like to know if you are still using the stock TMIC or not.
nice numbers... good driving and some drags could land you high 12's.:) |
becareful about the air fuel ratio at the low rpm range... u can still blow an engine at low rpms
Why not make some dyno pulls without freezing the IC to mimic what real driving conditions are like. Which shop did the turbo mods? |
Originally posted by j200pruf imflammable, is that turbo stock other than the compressor wheel, or did you use a t04b housing as well? I have the t04 compressor housing as well The Dyno was done at Track masters In Huntsville,AL $60 for 4 pulls with A W/B !! ( it was a Vw dyno day) FULL MODS BELOW |
Originally posted by Josepi I'm going to keep asking this in every hybrid thread I see. Turbine wheel stock/clipped? Boost response? NO clip--- My turbo builder (Jeff Amann) "Turbo Auto" 615-383-6242...... Told me that Clipping will drastically reduce turbo life & lag for that matter [QUOTE]Originally posted by Cheers! [B]becareful about the air fuel ratio at the low rpm range... u can still blow an engine at low rpms Why not make some dyno pulls without freezing the IC to mimic what real driving conditions are like. _ If I dont cool the IC before a dyno pull the engine heat will create an unrealistic Intake temperature... and I figure once the pull comences the ic temps will even out closely to Real life conditions |
^
|
Im considering building some of the same turbos For sale here on the forum....
It would Include.. T04b V-trim or H-trim wheel & Housing FULLY REBUILT with 360 Degree Thrust bearing S5 hotside with Manifold & lines Capable of 300-375+whp Polished compressor option ADD $25 -----$875------ If there is Any interest Please PM me |
Uh, there's a rule against advertising in here that is in direct competition with the vendors that do pay for advertising rights.
-Ted |
if im not mistaking .. it is a feeler .. seeing if there would be interest in it ... not advertising
|
I dunno if BNR is still active on here, but I think they have about the same prices or cheaper.
I think BNR used to pay for advertisement rights? -Ted |
https://www.rx7club.com/attachment.p...postid=2740653 :mad: that thing is not fun to install when its 15 degrees outside .. at 3 am in the morning .. trying to get it done intime to dyno it with no sleep !
|
Its not an advertisment, the Turbo is not even im my possesion..... Im just seeing if there is any interst... If there is I will teke it to the F/S section...
anyways here is a better shot of my turbo.. https://www.rx7club.com/attachment.p...postid=2740653 |
|
Originally posted by RETed I dunno if BNR is still active on here, but I think they have about the same prices or cheaper. I think BNR used to pay for advertisement rights? -Ted |
Originally posted by RETed I dunno if BNR is still active on here, but I think they have about the same prices or cheaper. I think BNR used to pay for advertisement rights? -Ted oops. doesnt looked like the real mods freaked out about it. so why did you? |
Originally posted by imflammable9 I dont get it why you feel the need to shoot somone down right from the get go. It is a very good price considering there is no core Involved & If someone is interested Why should they not have access to a Nice Upgrade option.... Sounds like your Opinion is a little Biased to me anyways I don't make the rules, nor do I enforce them. You obviously have no clue how things are done in here. You see the banners above? Those vendors pay to have them there. How would you like to be one of those vendors, who pay good money to advertise on this forum, and have some other vendor/person come on and advertise for free when they did not pay a cent for it? You think that is fair for them??? Your "very good price" is relative. What might be a nice price for you might be expensive to someone else. -Ted |
Originally posted by andrew lohaus since when have you been a moderator? oops. doesnt looked like the real mods freaked out about it. so why did you? You're stuck your foot in your mouth enough in other threads, and now you want to stick your nose in this one? It's not your beef. -Ted |
All times are GMT -5. The time now is 05:49 PM. |
© 2024 MH Sub I, LLC dba Internet Brands