There is also a GT-R sticker for some S4 models that you might want to make some of.

@RotaryResurrection - Thanks for the pics. They're in the works! I'm going to assume that they're the same size as the Turbo II decal - but if you have a measurement from one edge of the color to the other (e.g. from left most edge of the "G" to the right most tip of the "X") then I'll be sure to get it sized correctly. I'll be honest - because I'm cutting vinyl, the very thin stripes of this design are hard to do. I'll do my best, but they may have fewer "gaps" between the color just so there is sufficient material.

@RotaryResurrection - I'll look for pics of the GT-R, but assume it's in the same style as the GT-X.

I'm not sure if you mean the style of the sticker is to have cuts in it or if they are literally cut into lines, but I believe my GT-X fenders have solid stickers?

I will check when I get home tonight and take some measurements as well if you need them turbogslse

@FAL - I know what @RotaryResurrection means. I make these decals from two parts. One part is a clear decal cut to the overall shape or border of the decal (its the solid part). The second is the colored part (the letters themselves) and they are actually made by using a set of thin stripes to form the letters. I lay down the colored part onto the sticky back of the clear decal and then peel away the extra material to leave the thin stripes that form the letters. It's quite time consuming compared to normal decals, and I've priced them a little higher because of that. I think I could make 50 of the RX-7 hatch decals in the time it takes to make one fender decal. But hey, our rotaries are worth it!

Dimensions are always welcome. If they're from an FB, I can always measure from my own car, but I don't have any 2nd Gens, so actual dimensions are best. If you just take a photo of a ruler or tape measure next to the decal in both the horizontal and vertical directions, that's sufficient (and best).

My friend cuts vinyl as well and I've helped him out a little so I think I know what you mean. It's like doing a two layer overlay vinyl cut sticker. He uses arrows to line them up and it is a bitch to do them.

I will do as you requested with the measuring tape

Exactly - I have alignment marks as well, but these are small enough, and done one by one so I can hand-align them pretty well.

They are about the same length (I would guess) but about twice as tall as the "turbo II" sticker.

GT-X Measurements
 

Sorry it took a few days to get this up, holiday season and all.

I've attached the measurements of the GT-X sticker height, length, and detail. The detail to show that the original stickers were printed stickers, not two layer. I wasn't sure if you guys were saying that they were or just informing that you would be making them two layer, but the originals were definitely printed. My 87 TURBO II sticker is the same way.

Not that it would matter either way, but I just wanted to add it for future reference.

@FAL - Thanks for the pics! This is very helpful.

You're right- The original stickers are printed. Unfortunately, I don't have that equipment so I'm trying with a 2-layer approach. I have a technique that I'm happy with - see the attached pic.

My Turbo II stickers didn't use this same technique - so I'm going to try re-cutting them with this technique. The lines are cleaner all around and they're easier to make. Still time consuming, but easier.

I'll have to consider a single layer though I worry that the two-layer version will collect dirt under the decal. So, it may just end up that I do a single layer for best results.

Yeah that's what sucks about tiny vinyl. easily comes off. My buddy made a limited run of stickers for my photography company and they came out great but he warned me since the letters were soo small that they probably wouldn't hold up over time.

Glad I could help. Good luck with everything!

Just wanted to keep this thread updated, I finally finished painting and polishing my rear license plate bezel and applied the custom sized sticker being I have a vert. I'm extremely happy with the outcome, can't wait to install this unfortunately I will not be taking the car out much as I'm going to be doing a full paint job.

Attachment 651617Attachment 651618

Hey do you still make these decals? I want to order the rotary turbo with intercooler decal.

Thanks

Yes, I can still make them.

PM me with your info (name/address) and I'll send you one. Paypal for payment.

Dave

any chance you're still doing gods work?

Yep, can do decals still. Let me know what you're looking for.

hi mate still have tail light decals ?

Yes, I can do a set. I'm not sure if there's someone local who can do them to save on postage, but I can do a pair for you if you like. Or let me know qty. They're $2.50 USD each plus whatever postage will be to you.

Dave

hi Dave

you still make these ??

yeah mate interested , can’t PM on this forum yet ,

email maybe ? Cps3@live.com.au

Id love to have this on my FC airbox.. I need it!

https://farm4.static.flickr.com/3236...ff77524da2.jpg

To do that one properly, you need to do a screen print/dye sub type decal. Unfortunately, I don't have the ability to do that.

Dave

Hey, I am curious if you are still making these decals? I would like a rotary turbo sticker for my tail light if possible.

Yes, I can ship you out one. Just PM with your information and I'll get you pricing & paypal info.

Hello.I am interested in front fender and intercooler stickers.You have a pm.