Stainless V-band and U-bend supplier?
Anyone know of a good quality low cost supplier for 3" stainless U-bends and V-band flanges?
|
I posted the same thing on a Porsche forum and got good results. Why nothing from you guys? Don't want to tell?
|
|
Originally Posted by 13BT_RX3
(Post 9470567)
I posted the same thing on a Porsche forum and got good results. Why nothing from you guys? Don't want to tell?
http://www.racepartsolutions.com/ - These guys have donuts as well. http://www.globaltecheng.com/Product...?idCategory=31 - These guys are limited to 90 and 45 degree bends, but prices can't be beat. -billy |
Originally Posted by 13BT_RX3
(Post 9469152)
Anyone know of a good quality low cost supplier for 3" stainless U-bends and V-band flanges?
I got regular steel from them fast shipping and good products. that was 2.5 for my NA 12a now im going turbo 12a so im going to get 3 in from them probably... as long as i dont need 3.5 in :) |
Originally Posted by bwaits_
(Post 9470984)
You did not give us time :)
http://www.racepartsolutions.com/ - These guys have donuts as well. http://www.globaltecheng.com/Product...?idCategory=31 - These guys are limited to 90 and 45 degree bends, but prices can't be beat. -billy |
Originally Posted by zaridar
(Post 9471209)
Columbia River Mandrel Bending http://www.mandrel-bends.com/
I got regular steel from them fast shipping and good products. that was 2.5 for my NA 12a now im going turbo 12a so im going to get 3 in from them probably... as long as i dont need 3.5 in :) |
|
airflo
|
Originally Posted by 13BT_RX3
(Post 9471344)
Other sites mentioned elsewhere:
http://www.mandrelbendingsolutions.com/ http://www.verociousmotorsports.com/ http://www.atpturbo.com/Merchant2/me...egory_Code=FLG http://www.spdexhaust.com/ -billy |
Originally Posted by bwaits_
(Post 9471495)
|
Thanks for all the help finding components to make my exhaust system. It turned out pretty well, but I need to add a little flex to my down pipe.
http://i123.photobucket.com/albums/o...m/f976c0fa.jpg Does anyone know where I can find a 3" version of a ball joint with a graphite SS mesh gasket like this? http://i123.photobucket.com/albums/o...m/3d5fd05f.jpg Or...should I give up looking and add a flex coupling like this: http://i123.photobucket.com/albums/o...m/c18becac.jpg http://vibrantperformance.com/catalo...oducts_id=1013 |
i would use the flex piece... thats what i put on my 3.5 in stainless system... i think that it allows for more flex once it is installed... the ball connector is more to make it easier to fit initailly... correct me if im wrong... i got a similar ss flex piece and really like it
|
3 Attachment(s)
heres what is looks like.... i like it... easy to take off only two pieces besides that DP... also this is nice because there are NO BOLTS :)
|
Originally Posted by zaridar
(Post 10884084)
heres what is looks like.... i like it... easy to take off only two pieces besides that DP... also this is nice because there are NO BOLTS :)
|
yeah its tight.. thanks! i like the looks of yours too! looks good!
|
All times are GMT -5. The time now is 06:31 AM. |
© 2024 MH Sub I, LLC dba Internet Brands