Dual weber intake w/crbs on ebay...
http://cgi.ebay.com/ebaymotors/ws/eB...spagename=WDVW
Anybody think this is good? I'm either going to install my system with the money I have now or get some HP with it. Just wondering if this is any good for my 12A stock port. |
that is actually a good set-up, it was made by RE back in the mid-late 80's.
it will not give you the 50-60 the seller claims, esp not on a stock port 12A.. but i'd use one, I have seen them go for upwards of $400 I sold one a while back for $375. Watch it, and try to get it cheap. |
Actually there are two listings. One for the 13B and one for the 12A.
|
Honestly I think that this setup is crap. THe guy is lieing about the HP gain. There is no indiacation as to what the webers are... ie, 40mm, 48mm. They look pretty small to me.
I used to have a dual dellort 40mm setup on my 1st gen 12a block, and they produced roughly about a 45hp gain. I don't think that these that he has up for sale will produce more than 35-40hp. |
yeah the hp increase will not be as much, we have already established that.
But this is a good set-up, I used to have one, and actually may need another.... Because I have a dual side-draft set-up (like the one you mentioned) that uses dual Mikuni 44's... But due to the engine not being offset in my car as much as in the SA/FB chassis. I may not be able to use it.. therefore i'll need to go down-draft. Back to the weber set-up, it uses Dual Weber DCD's. (the same carb I retro-fited to my Model A to make it more reliable and easy to start) it most likely uses 34mm chokes. which would be 2 chokes per carb, so 4 34mm chokes (rather than say 2 45mm, like a 45 DCOE weber) ... However, some people with Bridgeported 12A's and 13B's swaped the chokes to 37mm. If you need more info, let me know, I can type some info from my old RE catalog if you need. |
Put all the info you can get in here and what other parts I'll need like fuel pump? fpr? etc
|
bump
|
I could really use some opinions please. THere's onlya day or two left and I don't know if I should get it.
|
I have this setup on my rx-7 and it is great when it's tuned and synchronized. Car and driver did a test of the Rotary Engineering (you can sort-of see the RE logo on the intake) Dual Weber 36/36DCD and said that it was 155 hp. That was with the whole kit that RE sold back in the early 80's. It's not the fastest thing around, but it's fun to drive, and easy to work on.
check my webpage for pics: http://www.caldwellphoto.com/jimmy -jimmy |
i had a set of the 36 dcds and LOVED them. loads beter low end than my 48dhla and killed the stock carb. i sold min when i removed the motor to do the 13bt swap
|
Go with a side draft.
|
I'm the one who won, I'll let you guys know how it works out.
|
Originally Posted by trainwreck517
I'm the one who won, I'll let you guys know how it works out.
|
Originally Posted by trainwreck517
I'm the one who won, I'll let you guys know how it works out.
|
Misthael,
I deleted your post. Despite the fact that you're mad at trainwreck517 for winning the bid, you didn't make it clear that you were bidding on it. The last message we got from you was:
Originally Posted by Misthael
I could really use some opinions please. THere's onlya day or two left and I don't know if I should get it.
Also, please in the future do not use obscenities or personally attack someone on the board. If you have a problem take it up in PMs. Posts like your last one will not be accepted here. Jon |
295 is a very very good price for that setup. Congradulations!
|
What did I say? I all ready forgot. I went to bed after that and haven't been home since I woke up. It's just really @#$^&*! annoying that every performance upgrade for my car is going to cost at least $800 and as soon as I find something on eBay for less I lose it. I know I shouldn't have posted it here now. The rotorheads I know are like brothers and wouldn't do that, but I don't know all of you and I should have expected some comeptition so oh well. Good luck with the carbs. Have a nice day.
|
just use this as your opportunity to go side-draft
|
I don't have almost a thousand dollars to spend. More like $500 max. I may just end up getting a rebuild and a tune up so it will run good for now. I'm starting to hate rotaries. Can't do crap with them here in OK. Just put a piston engine in them.
|
Can I have your avatar if you quit the team ?
|
It'll cost ya $50. Took me forever to make. :D
|
Check the for sale section....Mikuni Carbs for sale
|
Originally Posted by Mikeydred
Check the for sale section....Mikuni Carbs for sale
|
How much should I expect to pay for a mikuni 44 with sidedraft 4 port intake? I was looking at one...
|
Originally Posted by calvinpaul
How much should I expect to pay for a mikuni 44 with sidedraft 4 port intake? I was looking at one...
I wish I could keep it for/with a Camden setup, but no way. |
All times are GMT -5. The time now is 06:37 AM. |
© 2024 MH Sub I, LLC dba Internet Brands