RX7Club.com - Mazda RX7 Forum

RX7Club.com - Mazda RX7 Forum (https://www.rx7club.com/)
-   1st Gen General Discussion (https://www.rx7club.com/1st-gen-general-discussion-207/)
-   -   Picked up another FB (https://www.rx7club.com/1st-gen-general-discussion-207/picked-up-another-fb-936366/)

IO_303 03-11-11 09:12 PM

I bought the motor that was in the flood tonight cracked it open and found this....

So far I have found no damage from the mud ant water. Looks like it just needs a good cleaning and new seals. I have not checked the specs on any of it yet, I will dig into that tomorrow.


http://i179.photobucket.com/albums/w...2/DSCF0725.jpg
http://i179.photobucket.com/albums/w...2/DSCF0724.jpg
http://i179.photobucket.com/albums/w...2/DSCF0723.jpg
http://i179.photobucket.com/albums/w...2/DSCF0722.jpg
http://i179.photobucket.com/albums/w...2/DSCF0721.jpg
http://i179.photobucket.com/albums/w...2/DSCF0720.jpg
http://i179.photobucket.com/albums/w...2/DSCF0719.jpg
http://i179.photobucket.com/albums/w...2/DSCF0718.jpg

mazdaverx713b 03-12-11 05:36 AM

that thing looks great! i would've cleaned it up, compresison tested it, and ran it instead of opening it up!

rx71king 03-12-11 06:41 AM

it good that he open it up . the mud would have acted like sand paper..

IO_303 03-12-11 07:03 AM

So, I don't think I will be able to run the stock carb as planned LOL. I was told it was lightly ported.....I like their definition of "lightly ported"

j9fd3s 03-12-11 04:27 PM

yeah that's a nice bridge! engine looks pretty nice though, clean it up, measure everything and replace anything that is out of spec + the rubber bits, and you've got a runner!

IO_303 03-12-11 08:48 PM

So with the discovery of the bridge port, do you think this setup will help?

intake:
Racing Beat bridge port Holley intake
Holley 650 double pumper
Quickfuel 150 gph fuel pump
Quickfuel adjustable fpr set for 6psi

IO_303 03-22-11 01:56 PM

So parts are starting to come in for the rebuild.

racing beat Gasket/o-ring kit (showed up yesterday)
FD corner seal springs from pineapple racing
Viton oil ring inserts from Atkins
3mm solid corner seals from Atkins

The tension bolts are in good condition and i plan to reuse them, and the apex seals were low miles. Can you guys think of anything i would be missing?

IO_303 03-31-11 11:51 AM

Well I was about to reassemble the engine last night only to find out my Faïence while cleaning my desk threw out my brand new FD corner springs and my Atkins solid corner seals

Now i am waiting on parts AGAIN!

DivinDriver 03-31-11 02:33 PM

Time to get a new girlfriend. "Cleaning your desk" is girl-speak for searching through your stuff.

IO_303 04-01-11 07:39 AM

Nah, she is just overly clean. I have come to expect the cleaning. I just need to confine my parts to the basement. She wont go down there :)


All times are GMT -5. The time now is 11:02 PM.


© 2024 MH Sub I, LLC dba Internet Brands