RX7Club.com - Mazda RX7 Forum

 
Page 1 of 20
1
2
3
4
5
11
Last »
Search: Posts Made By: BLUE TII
Showing results 1 to 25 of 494
Search took 0.20 seconds.
Forum: Build Threads
Jun 8, 2026, 01:56 PM
Replies: 26
Views: 1,062
Posted By BLUE TII

This is a great build! Subscribed. Please...

This is a great build!

Subscribed.
Please keep posting videos on your channel.
Forum: 3rd Generation Specific (1993-2002)
Apr 30, 2026, 04:24 PM
Replies: 42
Views: 4,147
Posted By BLUE TII

I'm pretty sure Matey and maybe some others in...

I'm pretty sure Matey and maybe some others in Australia tried dividers between the turbines and made less power as you lose flow area pretty much any way you cut it. It isn't ideal but there is...
Forum: Single Turbo RX-7's
Apr 29, 2026, 06:25 PM
Replies: 68
Views: 13,635
Posted By BLUE TII

EFR 8374 10psi at 2,000rpm and full 12psi boost...

EFR 8374 10psi at 2,000rpm and full 12psi boost before 2,500rpm. Even in lower gears.
Forum: Single Turbo RX-7's
Apr 29, 2026, 06:23 PM
Replies: 68
Views: 13,635
Posted By BLUE TII

Is there not enough room in the chassis to make...

Is there not enough room in the chassis to make the neck-down farther down the downpipe? Would've been ideal to have the reduction after the wg merge.

Yeah, there is, but it will become tight at...
Forum: 3rd Generation Specific (1993-2002)
Apr 28, 2026, 02:14 PM
Replies: 42
Views: 4,147
Posted By BLUE TII

While that is true, post turbine flow is highly...

While that is true, post turbine flow is highly turbulent- not laminar flow. This but is why the dead headed flow isnt as bad as it otherwise would be.

Still, would be better flow separated with...
Forum: 3rd Gen General Discussion
Feb 27, 2026, 07:35 PM
Replies: 7
Views: 934
Posted By BLUE TII

I love that the center brake light is lengrhened...

I love that the center brake light is lengrhened to highlight the "bridge" between the tail lights.

Not that anyone cares, but my dream tail lights would be that center brake light section with...
Forum: Haltech Forum
Jan 27, 2026, 01:58 PM
Replies: 36
Views: 1,900
Posted By BLUE TII

Thank you dguy! I should know better than to...

Thank you dguy!
I should know better than to assume big street port issues I couldnt tune out with my E6K couldnt be tuned out with the elite.

In fact I had already had some small progress...
Forum: Haltech Forum
Jan 27, 2026, 11:34 AM
Replies: 36
Views: 1,900
Posted By BLUE TII

I dont have any inside information, but Im sure...

I dont have any inside information, but Im sure the tuners at Haltech know the basics of tuning.

Therefore I believe the bad Haltech elite base timing maps were a management decision done over the...
Forum: Haltech Forum
Jan 27, 2026, 11:27 AM
Replies: 36
Views: 1,900
Posted By BLUE TII

You did the right thing putting in the previous...

You did the right thing putting in the previous ignition map over the elite base ignition. If you want a little added safety you can select a column (from the top) and page down the entire column or...
Forum: Haltech Forum
Jan 26, 2026, 11:15 PM
Replies: 36
Views: 1,900
Posted By BLUE TII

Im just tuning my large streetport 1500 on NSP. ...

Im just tuning my large streetport 1500 on NSP.

My feeling is that because of the 02 feedback lag the underlying "Base" fuel table (VE) is the issue. At 4-5,000rpm tiny variations in TPS have...
Forum: General Rotary Tech Support
Jan 22, 2026, 02:04 PM
Replies: 7
Views: 767
Posted By BLUE TII

A can of starting fluid was a common sight in the...

A can of starting fluid was a common sight in the pits during rotaries racing heyday.

Though, commonly used racing carb without chokes and locked ignition timing also werent helping the starting...
Forum: 3rd Gen General Discussion
Jan 22, 2026, 01:57 PM
Replies: 31
Views: 1,698
Posted By BLUE TII

FD feels unique in a couple of ways. You sit...

FD feels unique in a couple of ways.

You sit deep down inside this tiny form fitting interior and somehow have amazing visibility from all sides and back.

A miata with hardtop lacks this...
Forum: Build Threads
Jan 16, 2026, 02:11 PM
Replies: 130
Views: 32,802
Posted By BLUE TII

Thank you j9fd3s for posting that! I will...

Thank you j9fd3s for posting that!

I will start a new thread on current build soon.
Forum: Build Threads
Jan 16, 2026, 02:05 PM
Replies: 130
Views: 32,802
Posted By BLUE TII

This Bakemono wing was a small run reproduction...

This Bakemono wing was a small run reproduction of Top Fuel Racing body kit spoiler in carbon fiber.

Both are out of production as far as I know.

Toru Kumaki is Top Fuel Racing (TFR) if you...
Forum: Haltech Forum
Jan 12, 2026, 02:05 PM
Replies: 1
Views: 350
Posted By BLUE TII

So, looks like I set it up right, just base tune...

So, looks like I set it up right, just base tune was too rough for wideband to correct for.
Forum: Haltech Forum
Jan 9, 2026, 06:24 PM
Replies: 1
Views: 350
Posted By BLUE TII

Set-up for 1500 nsp with 4x 2ndary injectors?

Hello,

I stupidly bought 1500 instead of 2500 and am running 2x id1050xds primary and 4x id1300xds 2ndary injectors.

I wired inj 5 to front 2ndary and inj 6 to rear 2ndary at the harness to ecu...
Forum: General Rotary Tech Support
Jan 7, 2026, 08:54 PM
Replies: 8
Views: 693
Posted By BLUE TII

The side seal slots are all different lengths. ...

The side seal slots are all different lengths. Each slot is stamped with a character denoting their length catagory.

You will see katakana characters at each slot.

Anyways.... once you inspect...
Forum: Suspension/Wheels/Tires/Brakes
Dec 30, 2025, 04:23 AM
Replies: 768
Views: 533,933
Posted By BLUE TII

Gooflw searxh "18x10 mustang wheel" for cheap...

Gooflw searxh "18x10 mustang wheel" for cheap 18x10 deep offset 114.3x5 wheels.

1st hit on quick search just now....
Forum: 3rd Generation Specific (1993-2002)
Dec 21, 2025, 11:28 AM
Replies: 43
Views: 1,951
Posted By BLUE TII

. Yeah, I am just bedding in an engine I...

.

Yeah, I am just bedding in an engine I rebuilt with both oil filler nipples open. No issues since Im not doing any of the things that slosh oil up there (cornering/braking/accel gs).

I dont...
Forum: 3rd Generation Specific (1993-2002)
Dec 21, 2025, 11:20 AM
Replies: 43
Views: 1,951
Posted By BLUE TII

A catch can will minimize fuel dillution of oil...

A catch can will minimize fuel dillution of oil if you allow it to have high "crankcase" flow through it.

This could be using both oil filler nipples with adequate sized hose to an open vented...
Forum: 3rd Generation Specific (1993-2002)
Dec 17, 2025, 11:35 AM
Replies: 43
Views: 1,951
Posted By BLUE TII

In endurance racing it was one of Mazda's pit...

In endurance racing it was one of Mazda's pit crew job to remove excess oil from the engine. The oil became more and more gasoline as the races progress
Forum: 3rd Generation Specific (1993-2002)
Dec 17, 2025, 11:31 AM
Replies: 43
Views: 1,951
Posted By BLUE TII

Typically this issue has more to do with reusing...

Typically this issue has more to do with reusing oil control rings, side housings with some wear or porting that violates the oil seal track.

Cleaned/flow tested injectors, not running excessively...
Forum: Single Turbo RX-7's
Dec 16, 2025, 02:20 PM
Replies: 46
Views: 4,944
Posted By BLUE TII

HKS specialized castings I knew of was T04Z and...

HKS specialized castings I knew of was T04Z and T51R and T51R KAI compressor covers and exhaust housings with tailored AR.

HKS is cast into these, so not just a mix of garret parts on those...
Forum: Single Turbo RX-7's
Dec 12, 2025, 02:00 PM
Replies: 46
Views: 4,944
Posted By BLUE TII

The HKS turbos have several small tweeks and...

The HKS turbos have several small tweeks and special castings that specialize them to the application and set them above the base garrett turbos.

Poor results with the base garrett t04z versus the...
Forum: 3rd Gen General Discussion
Dec 1, 2025, 01:53 PM
Replies: 46
Views: 5,522
Posted By BLUE TII

Sound clip? :yum:

Sound clip? :yum:
Showing results 1 to 25 of 494
 
Page 1 of 20
1
2
3
4
5
11
Last »


 
Forum Jump


All times are GMT -5. The time now is 08:28 AM.