1979 Rx-7 Turbo LS powered.
3 Attachment(s)
79 rx7 back halfed.
Alum Dash. Currie 9 inch with 35 spine moser axles and spool Competition engineering ladder bars and wheelie bars Roll cage 29x12 Slicks Kerkie racing 1/2" SS fuel system 12 Gallon Fuel cell Magnafuel prostar 725 pump 2001 5.3 LS motor. 6.0 #317 Casting heads (mildy hand ported) LS9 MLS Head gaskets Zr1 LS9 cam S400Sx3 75mm Turbo 1.10 AR T4 housing. AEM EMS fuel management 120lb injectors PowerGlide 1.76 PTC 9.5 converter Attachment 680530 Attachment 680531 Fabbed up Eng mounts. http://i17.photobucket.com/albums/b1...211_161328.jpg Cut up and welded the 98 F-body stamped steel manifolds. Used a mig and tri-gas. Actually welded nice. Attachment 680532 |
10 Attachment(s)
Quick and dirty hotside with junky “T” merge.
Attachment 680520 Attachment 680521 Attachment 680522 Attachment 680523 WG dump tube finished. Attachment 680524 Attachment 680525 Cleaned things up a bit and threw the ZR1 cam in. All the roller lifters looked good, gonna run them "as is" too. Got the new LS3 style cam gear with pick up installed. Going to run a LS3 style timing cover with cam pick up on the front. Attachment 680526 http://i17.photobucket.com/albums/b1...014_143356.jpg Hatch backs and fuel cells are a pain! No room under the cell, so I had to make a fire box. Attachment 680527 Attachment 680528 Attachment 680529 |
9 Attachment(s)
Long block
LS2 Timing cover w FWD cam pick-up is done. ARP stud kit and LS9 7 layer MLS Hg's are all in and torqued. Turbo oil supply done. Attachment 680511 Attachment 680512 Attachment 680513 Attachment 680514 Attachment 680515 Attachment 680516 IC mounted cleaned up Engine bay Attachment 680517 Random inter-cooler shot. (31x12x4) Attachment 680518 Final Pin. Attachment 680519 |
6 Attachment(s)
Welded up a little angle iron mount for the battery and test fit the hood. Plenty of clearance. also wired up the alternator charge cable (2g) and ground wire. Got the upper and lower radiator hoses, steam vent, throttle cable, and IAT sensor done. Went with the cheapo "golden rod" filter again. Installed and finished up the fuel return. Fuel plumbing is done.
Attachment 680505 Attachment 680506 Attachment 680507 Finishing up the wiring now… Attachment 680508 Attachment 680509 Attachment 680510 |
awesome build!
|
Wow. This is definitely going to be an adrenaline inducer! I'm surprised there's not a GNX motor in there. Is this the same car you were building the 12AT for a few years ago?
|
Originally Posted by aws140
(Post 11397429)
Wow. This is definitely going to be an adrenaline inducer! I'm surprised there's not a GNX motor in there. Is this the same car you were building the 12AT for a few years ago?
I’ll miss the 3.8’s, but my GN days are over. I just sold by black GN powered RX-7 (FC) last month. Parts are expensive and hard to find. Not to mention 1980’s technology,flat tappet cams, crappy flowing heads etc… The new LS motors are decades ahead of the old buick motors and can be picked up for 200-500 complete at most junk yards. Not to mention cheap used parts and current aftermarket performance parts. |
looks amazing!
|
Great progress!
|
3 Attachment(s)
Cruised around the block today and did a little trans-brake testing. Won't be long now!
Here is my fancy 4" necked down to a 2.5" muffler setup. I just welded around the body of the muffler. It' spretty quiet for a "race" car. You could easily have a conversation in it while cruising. :) Attachment 674690 I'll be running a 60mm wastegate like this as an exhaust cutout. I'd have it installed but the gate I was sent had a torn diaphragm. Attachment 674691 Attachment 674692 |
Good lord your car is a beast!
|
What kind of track times are you looking for?
|
Originally Posted by Netherlandrj
(Post 11449146)
What kind of track times are you looking for?
|
5 Attachment(s)
I'm calling the exhaust done. The new gate they sent me was crap as well. I used parts from the both of them to make one working gate. Not that it wasn't expected, but I wouldn't suggest "godspeed" products. They are pretty much crap. I also cut the supplied Wg spring in half and heated it with a torch to weaken it quite a bit. Shouldn't take much boost to open it.
Also installed an exhaust crank case evac kit. It's pulling vac at idle. And gets much stronger in the revs. Heres the finished product. http://i17.photobucket.com/albums/b1...ps0f94f89d.jpg Wrapped Attachment 673766 Video of the WG actuating with some shop air. http://i17.photobucket.com/albums/b1...psb8c0da49.jpg Hard to see but the evac kit is pulling vac at idle. http://s17.photobucket.com/user/Hybr...b19db.mp4.html Also got new window crank assys, glass, door handles And pop rivited some alum door covers on. Now both windows work on this "street car". Attachment 673767 http://i17.photobucket.com/albums/b1...psa3e8bb5c.jpg Installed some $50 ebay coil overs to raise the front end a couple inches. While I was playing with the suspension I figure I should upgrade the brakes. Ordered a set of drilled and slotted rotors with some HAWK pads. Attachment 673768 Wrapped the dump tube and brake lines. Attachment 673769 Ordered a cheap ebay oil catch can. Came with no baffles. Was just straight in and out. Installed some brass SOS pads and tubing to help baffle the oil mist. Should work well now. I have the same setup on my other car. Not sure if I will even use it now that I am running an exhaust evac setup. If anyone wants It I'll sell it for $30. Attachment 673770 |
5 Attachment(s)
CF Hood finally came in. Got rid of the hood pins and installed a factory latch.
Just need to borrow some street legal tires so I can go try to tag this thing... Attachment 670103 Attachment 670104 Attachment 670105 Made another HVAC cold air intake too. I found you can pull the segments apart and add to them for one longer seamless piece. This also let me eliminate the “crinkled” end pieces. There’s even a rolled bead on the end for your couplers. This one is hidden in the fender so I didn’t spend any time sanding it or trying to make it look pretty. If you want it to look more professional you could try just enforcing the ends with glass/resin. Then dipping the whole assy in polyurethane. I think that would turn out slick. http://www.homedepot.com/catalog/pro...dc22bc_300.jpg http://i17.photobucket.com/albums/b1...ps81106037.jpg Attachment 670106 Attachment 670107 |
great work man that thing is clean. what are your goals for power output?
|
Not looking to break any Hp records. Spent all the money on the turbo setup and car. Eng is a junk yard special $220. Hoping For about 600.
|
Of all the legit reasons to not pass my out of state inspection they shot me down for no odometer today. Makes no sense to me. Inspector told me it didn't even have to work. Suppose I'll count myself lucky and velcro on on the dash for a day. ;)
|
Anytimes with the new set up?
|
1 Attachment(s)
Originally Posted by sandbag
(Post 11513995)
Anytimes with the new set up?
If it holds together It's got alot of room for improvement. Attachment 667560 |
1 Attachment(s)
Make that 9.66 @144.6 :D
18.5lbs. 15* timing Started dropping speed at 19.5lbs, I think my super quiet exhaust may be killing me. May make a quick 4" DD with no muffler and give it a go. The timing dropping so low may be killing me as well. Only got 3 runs in. Attachment 667035 |
It's so quiet it almost sounds like the dump isn't opening.
|
|
O_o
That thing is a goddam spaceship! |
Originally Posted by TheAnalogKiddd
(Post 11525933)
O_o
That thing is a goddam spaceship! |
All times are GMT -5. The time now is 03:46 PM. |
© 2024 MH Sub I, LLC dba Internet Brands