my 87 TII dyno
1 Attachment(s)
Emissions, Power Steering, and A/C removed,3 inch down pipe,greddy catback,s5 turbo, street port,fcd,safc neo,255 fuel pump,12psi,O2 set at 12. pull was done in 3rd.
|
pretty impressive, that's at about the limit of the stock turbo.
|
I thought you were supposed to dyno in fourth gear for the '7... Not that you have to, but I remember reading that. I believe it was because it has the ratio closest to 1:1.
|
if you are comparing two cars in the same gear does the ratio mater?
|
the gear shouldnt matter, a higher gear just helps teh turbo to spool better. last time mine was on the dyno i made only two more hp in 4th, so not much difference
it is weird how wavy the graph is. what was the boost at redline? |
12 psi
|
I just recently read some dynos can also correct for a non-1 gear ratio. Some people may also be forced to run a less than optimal gear for speed reasons, usually because the tires won't take the abuse. Yesterday Syonyk made the dyno operator's first flat tire in his first gen, lol
|
People get too hung up on running in 4th gear.
It doesn't matter. As long as you're comparing runs in the same gear, that's the only time it matters. You still have drivetain loss, and running 1:1 doesn't mean jack shit. I don't like this dyno graph cause it's too wavy. Wavy means possible problems... -Ted |
1 Attachment(s)
pic of my car
|
nice numbers what kind of dyno? i had your same mods except i was stock port so you should be making a little more, i made 240 @ 12psi
|
DYNO-mite Dynamometer
Affordable Engine Dynamometer and Chassis Dyno systems. www.land-and-sea.com CHASSIS DYNO - Land & Sea 'Pro 1200' installed in-ground - with easy drive-thru access. Air/Fuel Ratio sampling to precisely Tune Front- or Rear-Wheel-Drive vehicles, producing up to 1200WHP. |
13b could you list your mods
nice numbers dave |
i was using a dyno jet so that may be the why you didnt make as high of numbers, some dynos read lower i dont know why that is.. well i made 240 on my old setup which was a stock atkins reman with 3mm seals, RB full exhaust hybrid S4 turbo, SAFC2, FMIC, 550 prim 720 sec injectors.. come to think of it i guess your turbo was stock so that may be why my numbers were higher too. mine was upgraded.
|
Originally Posted by 13bturbofc
(Post 8224899)
i was using a dyno jet so that may be the why you didnt make as high of numbers, some dynos read lower i dont know why that is.. well i made 240 on my old setup which was a stock atkins reman with 3mm seals, RB full exhaust hybrid S4 turbo, SAFC2, FMIC, 550 prim 720 sec injectors.. come to think of it i guess your turbo was stock so that may be why my numbers were higher too. mine was upgraded.
|
i liked it but i have a problem, im always on a quest for more power so i only had it for a year then i went with a hks T04R and im now making 400whp lol
|
Nice torque curve.
|
This was my old car about 3-4 years ago.
The car is pretty solid but i never got around to dyno'n or getting it on a wideband back then so it's nice to see what it was doing (I ran about 10psi). I agree with Ted on that dyno graph. The car needs a wb and bigger injectors then you might be able to tune those waves out. |
All times are GMT -5. The time now is 08:10 PM. |
© 2024 MH Sub I, LLC dba Internet Brands