RX7Club.com - Mazda RX7 Forum

RX7Club.com - Mazda RX7 Forum (https://www.rx7club.com/)
-   Single Turbo RX-7's (https://www.rx7club.com/single-turbo-rx-7s-23/)
-   -   S4 t2 half bridge turbo (https://www.rx7club.com/single-turbo-rx-7s-23/s4-t2-half-bridge-turbo-1124076/)

86t2 03-07-18 05:59 PM

S4 t2 half bridge turbo
 
Hey guys I'm looking for some support here in deciding which turbo would be best for my build. As stated I have a s4 t2 with s5 internals with a bridge port on the secondaries and street port on the primary. So I'm looking to make 400-500hp and I'm counting on a Borg Warner sxe series to get me there. I only plan on turning 8k rpm with this engine and yes I'm aware that it won't get all the power that it's capable of at that rpm. With that being said there are a lot of options with these turbos. Any help with sizing and a/r would be appreciated. Thanks in advance.

Turblown 03-08-18 12:03 PM

The 8376 will do it with ease and best response. We have them in stock. Use the 1.0 a/r for your porting.

86t2 03-08-18 04:43 PM

Thank you for your help! What type of flange comes on that exhaust housing?

Turblown 03-08-18 05:04 PM


Originally Posted by 86t2 (Post 12258938)
Thank you for your help! What type of flange comes on that exhaust housing?

The turbine discharge is a 3.5" marmon, diesel style. Same as the older SX airwerks turbos. I actually prefer those over vbands.

https://turbosource.com/collections/...0-800-hp-turbo

https://turbosource.com/collections/...-flange-3-5-ss

0piston 03-23-18 03:30 PM

Would this turbo you suggested the 13009097056 also be best suited to a 13b-rew fd motor with a half bridge. looking for the best response and midrange/ best suited for this engine.
im thinking about jumping on your group buy for the ewg manifold, but may also consider your iwg design. thanks for your input.

Turblown 03-23-18 09:54 PM


Originally Posted by 0piston (Post 12262740)
Would this turbo you suggested the 13009097056 also be best suited to a 13b-rew fd motor with a half bridge. looking for the best response and midrange/ best suited for this engine.
im thinking about jumping on your group buy for the ewg manifold, but may also consider your iwg design. thanks for your input.

Turbo selection really doesnt matter that much between an fc and fd engine. Fc is a little lazier if its an s4( lower comp rotors and heavier mass). The s4 and s5 make a little less power than the fd engine.

Surprisingly we have made good power on with the iwg system on half bridge engines. So have others with our kit. I believe its a little misleading if trying to compare psi between setups. The halfbridge has a much higher VE and makes more power at the same psi, however its using a lot more of the wheels airflow. So you will max a turbo out much sooner. Also you wont see 30 psi by 3400rpms, but you will see similar low end power( compared to smaller ports).

If using pump gas only I would go ewg.

AarenNinja 04-12-18 07:18 AM


Originally Posted by Turblown (Post 12262826)
Turbo selection really doesnt matter that much between an fc and fd engine. Fc is a little lazier if its an s4( lower comp rotors and heavier mass). The s4 and s5 make a little less power than the fd engine.

Surprisingly we have made good power on with the iwg system on half bridge engines. So have others with our kit. I believe its a little misleading if trying to compare psi between setups. The halfbridge has a much higher VE and makes more power at the same psi, however its using a lot more of the wheels airflow. So you will max a turbo out much sooner. Also you wont see 30 psi by 3400rpms, but you will see similar low end power( compared to smaller ports).

If using pump gas only I would go ewg.

I'm new to this so turbo selection really doesn't matter? I'm gonna try to do a REW swapped or 88 TII swapped vert (S4) sometime this winter when I finish moving.


All times are GMT -5. The time now is 03:51 AM.


© 2024 MH Sub I, LLC dba Internet Brands