![]() |
rear diffuser
That is the exact Rear Diffuser I have been looking for! Does anyone know if there are any left available and where I can go to purchase one? Thanks again for the help!
|
Originally Posted by exmanos
(Post 6948769)
Mine arrived yesterday at customs...first they asked me to pay 450$ to release it and after i had a big argue with them they dropped at 210$...i'll propably have it by tomorrow....
|
Got it!Finally paid 160$ :( ...they didn't know what it was so they were charging anything they wanted and they thought it was plastic...Ken stop doing such a great job it took me ages to convince them that this was fiberglass :wallbash: ...
|
I whant I need, is it to late to get in on this. If not pm me ken so that I can send full payment Thank's Jesse.........
|
MONEY SENT for the deposit!!
thanks guys and keep up the awesome work!!! -josh |
I never understood how customs came up with their fees. I always try to lower the value as much as I see fit to not raise a red flag.
In case any of you guys didn't know, the group buy is already closed. The price is now $350 + shipping. I think that's a fair price and fair for the initial participants. Ken |
Fisnished installing, looks gr8. i'll post better pics 2morrow
|
Looks good, i cant wait to install mine.
|
I finally got around to installing my original re diffuser. I'm lovin' it!
|
more pics
|
Looks awesome. Can't wait for mine.
|
Hey Shine, you guys to #19 yet?
J. Fitz |
Originally Posted by turbogarrett
(Post 6956432)
I finally got around to installing my original re diffuser. I'm lovin' it!
|
Originally Posted by RX7Junkman
(Post 6956655)
more pics
|
Originally Posted by herblenny
(Post 6949778)
weaklink,
I haven't painted my RE diffuser from chuck (just black gel coat) and its been doing fine. I figure it'll get dirty and get chipped and eventually, I'll get it painted.. But looks fine since its mounted so low. Ken, Have you made one in CF yet?? PHIL |
Alternative to Rhino Liner
3 Attachment(s)
I wanted to share with those of you considering the Rhino Liner coating that there is a nice alternative at the auto parts store. Dupli-Colors Truck bed Coating TR-250 ($8) and Dupli-Colors Adhesion Promoter CP199 ($5).
1. Used Dawn to wash off release agents. 2. Then I lightly used 600grit to prep the surface for the adhesion promoter. Rewash or wipe down. 3. Follow the recommendation on the adhesion promoter applying 2-3 thin coats allowing 2-3 minutes between each coat. 4. Now for the Truck bed liner coat. Shake well. Apply this with in 10 minutes of your last coat of adhesion promoter. Spray 8-10 inches away from the surface. I tested my technique out on the rear section that is hidden from view. 5. I then covered the entire surface, focusing on what would be seen most or probably meet with some curbing. I particularily coated both piecs that wrap around the fender really well. You don't want to lay it on to heavy that it begins to look glossy or puddled. 6. I also coated the edges that would be seen on the fenders. When the Truck Bed Coating starts reaching the end of the can it will start spitting out larger particles. STOP using it. Always keep the can as close to upright as possible. And you can never shake the can to much during use. I used all of one can. I probably laid down two coats total over the entire surface and five to six coats total on the places I thought would see the most traffic. Also if you're worried about losing the marks for the mounting holes then pre-drill through the center or completely drill them out prior to washing and prepping. I drilled them out after I was done painting. I used an x-acto knife to find the center and spun the blade back and forth creating a divot and then I slowly worked my way up with different sized bits. Definitely pre-drill with at least an 1/8 inch bit and then finish with one that matches the size of the mark. Below are a few pics that show how uniform the texture is. The best part is should it ever get damaged or scratched touch up is easy. Also I test sprayed armor all on it and it looks great. (Use a spray or sponge, not cloth.) Thanks to Ken and his crew for producing some of the best parts out there for our cars. |
car hugger, very nice. I might just do the same
|
wow they they look sick on ur guys cars very nice stuff
|
|
Great pictures guys
|
Looking good. I hope I can see one of your diffusers over the summer when I'm back in Miami.
|
What number are we on the GB?
|
And when do you want full payment?
|
car hugger, very good job !
|
Originally Posted by afgmoto1978
(Post 6961112)
And when do you want full payment?
+1 you should ship them on a paid in full basis.... ;) (im #31) |
All times are GMT -5. The time now is 01:48 PM. |
© 2024 MH Sub I, LLC dba Internet Brands