RX7Club.com - Mazda RX7 Forum - Search Results

 
Search: Posts Made By: coldy13
Showing results 1 to 25 of 441
Search took 0.61 seconds.
11-18-15, 12:33 AM
Replies: 8
Views: 2,606
Posted By coldy13

Doesn't matter, but it's a good thought for...

Doesn't matter, but it's a good thought for keeping gear wear patterns the same when rebuilding transmissions.

The driveshaft is balanced independently, and the yolk for the tranny and the flange...
11-17-15, 11:57 PM
Replies: 7
Views: 836
Posted By coldy13

It's a speed hole :) My '85 has another hole...

It's a speed hole :)

My '85 has another hole a couple inches above that, just like the bolt holes for the tail lights. It's been too long since I tore it apart, can't remember if there was a clip...
09-09-13, 10:10 PM
Replies: 12
Views: 867
Posted By coldy13

Stay far away from glasspacks and cheapo...

Stay far away from glasspacks and cheapo mufflers. They might sound good at first, but in a short time they'll burn out and be louder than if you had just run a straight pipe. If you can fab up...
08-09-13, 05:47 PM
Replies: 6
Views: 1,210
Posted By coldy13

Diamond Racing Wheels...

Diamond Racing Wheels (http://www.diamondracingwheels.com/)
or
Circle Racing Wheels (http://www.circleracing.com/)

Either one will be able to make a custom wheel with whatever measurements you...
08-01-13, 09:46 AM
Replies: 14
Views: 907
Posted By coldy13

The pilot bearing could be shot, or something is...

The pilot bearing could be shot, or something is wrong with the clutch hydraulics or throw out bearing/clutch fork.

If the clutch pedal feels normal, my bet is on the pilot bearing, especially...
07-12-13, 02:55 PM
Replies: 215
Views: 38,810
Posted By coldy13

Still lots of work to do but it's getting there...

Still lots of work to do but it's getting there slowly...
http://i.imgur.com/MaQ8hiU.jpg
http://i.imgur.com/5zUVBZ3.jpg
http://i.imgur.com/37qMLNX.jpg
07-12-13, 02:49 PM
Replies: 9
Views: 871
Posted By coldy13

The hex part is actually separate from the...

The hex part is actually separate from the threads and taper, it's splined and pressed on. I did it so long ago I forget, but I'm pretty sure it's 1/2" knurl studs that will press right in, or you...
Forum: Build Threads
06-15-13, 03:02 PM
Replies: 299
Views: 62,378
Posted By coldy13

I'd just wire a switch to the control side of the...

I'd just wire a switch to the control side of the relay for now, at least it'll run until you figure out the issue with the ecu. Any chance you're hooked into the wrong wire on the haltech? or you...
06-12-13, 07:14 AM
Replies: 47
Views: 3,316
Posted By coldy13

they have a check valve stock, if it still works...

they have a check valve stock, if it still works or not is another question... I added a check valve to mine since the one inside my booster wasnt working. After boosting it took a couple seconds...
05-28-13, 09:01 PM
Replies: 4
Views: 622
Posted By coldy13

If it looks straight on a table and you don't...

If it looks straight on a table and you don't notice anything when you drive it then it's good enough. Checking it on the car is the best way though, and it's the easiest since you only need to take...
05-28-13, 05:34 PM
Replies: 4
Views: 622
Posted By coldy13

Clean up the axle flange real good where the...

Clean up the axle flange real good where the wheel bolts on, and use a dial indicator on the flange just outside of the wheel lugs. I think axle runout should be less than .008"-.0010", and end play...
05-21-13, 05:19 PM
Replies: 47
Views: 3,316
Posted By coldy13

One of these is the best way Mazda RX-2 : Oil...

One of these is the best way Mazda RX-2 : Oil Pedestal (Version 2) (http://www.re-speed.com/index.php/catalogue/rx-2/oil-pedestal-version-2-detail)

or you can put in a T fitting at the oil...
05-07-13, 08:48 PM
Replies: 47
Views: 3,316
Posted By coldy13

You can do the front mount IC without moving the...

You can do the front mount IC without moving the battery at all. Actually, I have a good IC and all the piping to do it and I wouldn't want much for it. There's just enough room between the sway...
04-21-13, 10:48 PM
Replies: 11
Views: 597
Posted By coldy13

Have you checed the dizzy cap and rotor yet? ...

Have you checed the dizzy cap and rotor yet? That's my #1 guess, once the contacts go bad the spark will still try to find a way to get through, so it arcs all over the place and causes missing like...
04-17-13, 10:52 PM
Replies: 6
Views: 1,222
Posted By coldy13

Ahh, thought you were talking about the...

Ahh, thought you were talking about the doors...didn't make sense being a race car but whatever. The FSM on foxed.ca will have the wiring diagram you need.
04-17-13, 07:20 PM
Replies: 6
Views: 1,222
Posted By coldy13

Why not just go straight to the battery? Keyless...

Why not just go straight to the battery? Keyless needs power all the time.
04-17-13, 06:20 PM
Replies: 4
Views: 555
Posted By coldy13

The TII brake swap isn't that expensive, but you...

The TII brake swap isn't that expensive, but you need the '84/'85 large spindles, aluminum calipers, bigger rotors, 4piston calipers. Drag racing you shouldn't have a problem even on the SA brakes...
04-17-13, 06:13 PM
Replies: 7
Views: 651
Posted By coldy13

I always just put on a drop of blue loctite and...

I always just put on a drop of blue loctite and hit it with my best 1/2 impact(not that great of one, I'm a cheapass FB owner afterall...probably 300ft/lbs), never had a problem. The first time I...
04-08-13, 09:17 PM
Replies: 9
Views: 2,122
Posted By coldy13

I had that problem with mine too, the stock line...

I had that problem with mine too, the stock line size should be good enough, most likely the line is clogged a bit. I ran a new return line same as the stock size from the regulator to the tank and...
04-07-13, 11:35 AM
Replies: 20
Views: 3,559
Posted By coldy13

I'd stay away from the coffee can type, the cheap...

I'd stay away from the coffee can type, the cheap one I had made my car louder than a straight pipe... If you want a cheap one to get you by, I'd get one of these Thrush Turbo Mufflers - JEGS...
04-06-13, 09:02 PM
Replies: 20
Views: 3,559
Posted By coldy13

That'll throw a bit of fuel into the exhaust too....

That'll throw a bit of fuel into the exhaust too.

It happened to me the same way, as soon as the engine cranked, muffler went boom.
04-06-13, 08:49 PM
Replies: 10
Views: 662
Posted By coldy13

Nice work man, looks like a real clean setup. ...

Nice work man, looks like a real clean setup. Does the hood fit with the intercooler like that or are you planning on running a big scoop?
04-06-13, 08:22 PM
Replies: 20
Views: 3,559
Posted By coldy13

LOL, first I've heard of it happening to someone...

LOL, first I've heard of it happening to someone else :) That happened to me back when I first got my rx-7. Rwatson has it right, fuel getting into the exhaust, start the car...and BOOOOOOOM!!! ...
04-06-13, 02:40 PM
Replies: 50
Views: 31,818
Posted By coldy13

The TII turbo is probably the way you want to go...

The TII turbo is probably the way you want to go for a budget build. The stock TII exhaust manifold is easy to mod to fit the 12a engine, and you can pick the turbo up cheap, probably less than you...
04-05-13, 10:26 PM
Replies: 15
Views: 1,127
Posted By coldy13

It's closer to 2000-2500psi, maybe a bit less for...

It's closer to 2000-2500psi, maybe a bit less for older cars with no ABS, but other than that spot on. If you drive it like that the first time you really hit the brakes it's going to blow out on...
Showing results 1 to 25 of 441
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.