RX7Club.com - Mazda RX7 Forum - Search Results

 
Search: Posts Made By: Falcoms
Showing results 1 to 25 of 170
Search took 0.48 seconds.
11-14-11, 12:45 PM
Replies: 52
Views: 11,375
Posted By Falcoms

724494 Mind you this is with the stock VDI...

724494

Mind you this is with the stock VDI intake and 8.7:1 rotors. I don't know about anyone else, but with that broad of a torque curve, the 6 port half bridgeport seemed like a great upgrade...
11-02-11, 01:51 PM
Replies: 52
Views: 11,375
Posted By Falcoms

It was already pre-existing in the iron. As for...

It was already pre-existing in the iron. As for the position of the bridge, I didn't actually measure it out or anything, I just based it on the way the seal tracks on the side plates were worn in. ...
10-31-11, 12:49 PM
Replies: 52
Views: 11,375
Posted By Falcoms

if you're using used plates, it's easy. you have...

if you're using used plates, it's easy. you have a darkened area where the rotor housing sits on the side plates. I didn't do a j port or anything fancy, just a couple of eyebrows, leaving about...
10-21-11, 01:24 PM
Replies: 52
Views: 11,375
Posted By Falcoms

On mine I ran eyebrows on both the secondary and...

On mine I ran eyebrows on both the secondary and aux ports on my s5-N/A block, leaving the primary's just with a large street port. It yielded amazing drivability on the street, and a nice, broad...
10-20-11, 01:59 AM
Replies: 10
Views: 509
Posted By Falcoms

I believe that it goes into the back of the lower...

I believe that it goes into the back of the lower intake manifold if memory serves. You can go ahead and block it off and eliminate it. Obviously, if it's not currently hooked up and the car is...
10-11-11, 12:52 PM
Replies: 20
Views: 3,479
Posted By Falcoms

You can easily out-brake an ABS equipped FC in...

You can easily out-brake an ABS equipped FC in any weather condition even as a mediocre driver. Absolutely not worth it in anyone's book. I don't run ABS on my race-prepped FC, and it's perfectly...
Forum: Haltech Forum
09-01-11, 11:39 PM
Replies: 1
Views: 403
Posted By Falcoms

I should also mention that it's not just the...

I should also mention that it's not just the tach, but also in the haltech software it's reading the bouncing RPM signal. Also it does it at all loads as well as zero throttle
Forum: Haltech Forum
09-01-11, 01:44 PM
Replies: 1
Views: 403
Posted By Falcoms

sporradic ignition between 2500-3000rpm

Hey all, I'm having a bit of an unusual issue in my car. The tach jumps sporadically (up to 1k rpm either way) and the engine runs for crap between exactly 2500rpm and 3000rpm. as soon as it's...
07-15-11, 12:11 AM
Replies: 14
Views: 4,148
Posted By Falcoms

I'm rocking a set of DCOE-style side-draft ITB's...

I'm rocking a set of DCOE-style side-draft ITB's on my bridged n/a 13B-RE, works awesome for throttle response, especially with the ram air box off of the TII hood scoop. Not sure why so many people...
11-05-10, 06:08 AM
Replies: 150
Views: 8,719
Posted By Falcoms

I'm running a Haltech e11v2, and it's never...

I'm running a Haltech e11v2, and it's never missed a beat, even driving back and forth to work when it was 50 miles each way. Hell, the only problem it ever had was because of a 20 year old, 225,000...
07-25-10, 10:35 AM
Replies: 9
Views: 1,568
Posted By Falcoms

yeah, that be the parts you need. You're best...

yeah, that be the parts you need. You're best off doing that anyways, I mean it's a bitch to drop the rear sub frame, lets be honest. Might as well just bite the bullet and put the poly bushings in...
07-25-10, 12:50 AM
Replies: 9
Views: 1,568
Posted By Falcoms

no, if you burn out the rubber bushing (I assume...

no, if you burn out the rubber bushing (I assume you're changing out to poly), you can get access to a steel sleeve that's inside the rubber bushing that the bolt fits snugly to. The problem is that...
07-24-10, 07:42 PM
Replies: 9
Views: 1,568
Posted By Falcoms

hold off on the cut off wheel. What happened...

hold off on the cut off wheel. What happened when I ran into this issue was the bolt was rusted in the sleeve inside the rubber bushing. What I did was drill a hole in the sleeve with a good 3/16...
06-23-10, 08:08 AM
Replies: 18
Views: 3,616
Posted By Falcoms

I go to Shook Motorsports in Rockford, IL. He's...

I go to Shook Motorsports in Rockford, IL. He's a great guy, has his own dyno, and he did wonders with my E11v2. He mainly does rotary's, but does other vehicles, too. Flat rate of $700 for a full...
01-11-10, 06:14 PM
Replies: 508
Views: 687,441
Posted By Falcoms

I'm also interested in the spec-M hood scoop...

I'm also interested in the spec-M hood scoop insert, very curious if you still offer these.
11-06-09, 11:09 AM
Replies: 46
Views: 52,404
Posted By Falcoms

well, I run 1/2 quart of 2 stroke per every 3/4...

well, I run 1/2 quart of 2 stroke per every 3/4 of a tank (roughly 12.5 gallons), and the engine I took apart from a blown coolant seal was absolutely mint: no scoring on the rotor housings, no real...
09-19-09, 07:46 PM
Replies: 26
Views: 1,179
Posted By Falcoms

Well, it was an all around good meet, lots of...

Well, it was an all around good meet, lots of fun, and I can't wait for next year!
09-13-09, 06:43 PM
Replies: 26
Views: 1,179
Posted By Falcoms

I think I'll be able to make it out for this. ...

I think I'll be able to make it out for this. I've got to make sure I've got nothing I agreed to otherwise, but it sounds like fun.

Also, for the BBQ, is this supplied or should we be looking at...
08-27-09, 11:02 PM
Replies: 20
Views: 774
Posted By Falcoms

Dare I ask why you are reducing fuel pressure? ...

Dare I ask why you are reducing fuel pressure?

Also, the stock FPR would have to be eliminated, so basically you'll need some billet fuel rails installed. Plus it eliminates the pulsation...
08-27-09, 01:56 PM
Replies: 20
Views: 774
Posted By Falcoms

If you're going to run an upgraded ecu, I'd...

If you're going to run an upgraded ecu, I'd recommend a full stand-alone, or at the very least a piggy-back system rather than a reflashed stock ecu. The reason I say this is that you can then...
Forum: Race Car Tech
08-27-09, 12:12 PM
Replies: 6
Views: 766
Posted By Falcoms

this is an article from grassroots motorsports...

this is an article from grassroots motorsports magazine about Sylvain Tremblay's ITS FC RX-7 that won the SCCA national championship 2 years in a row, and it lists the spring rates and other details...
08-07-09, 01:39 PM
Replies: 508
Views: 687,441
Posted By Falcoms

is the front aero bumper still made? I'm...

is the front aero bumper still made? I'm referring to this one:
http://img510.imageshack.us/img510/5467/resizedresizeditempics090106ys.jpg
06-10-09, 09:28 AM
Replies: 11
Views: 2,698
Posted By Falcoms

t-von: Though aux port reversion is a minor...

t-von: Though aux port reversion is a minor issue, it hasn't affected driving on the street in any detrimental way. Though the chart shows quite low torque in the low end, actually driving the car...
06-08-09, 07:20 PM
Replies: 11
Views: 2,698
Posted By Falcoms

Well, I had a moderate street port on it from...

Well, I had a moderate street port on it from when I built the engine the first time, but when it came time to tear it down due to the bad coolant seal, I just had an itch for more power. I figured...
06-08-09, 02:05 PM
Replies: 11
Views: 2,698
Posted By Falcoms

Nope, aux sleeves are completely removed, VDI is...

Nope, aux sleeves are completely removed, VDI is wired open, and there is not a single emissions component on the vehicle. Even with doing all this, the car has some serious bottom end grunt...
Showing results 1 to 25 of 170
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.