RX7Club.com - Mazda RX7 Forum - Search Results

 
Search: Posts Made By: rx3sum
Showing results 1 to 25 of 146
Search took 0.10 seconds.
Forum: Microtech
02-16-19, 06:41 PM
Replies: 3
Views: 478
Posted By rx3sum

Hey Arran im not 100% sure but think you need to...

Hey Arran im not 100% sure but think you need to use the factory FC 3 coil setup with LT10S.
Forum: Microtech
11-04-18, 11:40 PM
Replies: 4
Views: 1,046
Posted By rx3sum

Your idle map and load map are not compatible...

Your idle map and load map are not compatible with each other. Idle to suit 550s and load to suit much larger injectors.
Take it to a tuner to sort it.
Forum: Microtech
11-01-18, 08:51 PM
Replies: 4
Views: 1,046
Posted By rx3sum

Idle map is way too high. It is suited to 550...

Idle map is way too high. It is suited to 550 injectors. What makes you think it is lean?
Is the tps set correctly?
Your load map also has a massive trough at 8 psi.
Forum: Microtech
11-01-18, 12:52 AM
Replies: 2
Views: 1,442
Posted By rx3sum

Microtech setup guide.

Here is a helpful clip from a trusted tuner in Australia.
https://www.youtube.com/watch?v=hBgQOxaecdY
Forum: Microtech
02-18-18, 05:12 AM
Replies: 4
Views: 945
Posted By rx3sum

Is air temp -21C correct? Whats idle AFR above...

Is air temp -21C correct?
Whats idle AFR above 82C water temp?
Forum: Microtech
02-15-18, 01:07 AM
Replies: 4
Views: 945
Posted By rx3sum

Looks like you need to calibrate the tps and...

Looks like you need to calibrate the tps and connect the air temp sensor up.
Check fuel pressure and timing.
10-07-17, 01:04 AM
Replies: 3
Views: 546
Posted By rx3sum

Search for TPS 101 guide.

Search for TPS 101 guide.
10-05-17, 05:28 AM
Replies: 3
Views: 546
Posted By rx3sum

Search how to check for codes on the ECU and get...

Search how to check for codes on the ECU and get the CEL issue sorted.
An NA auto will struggle to turn the tyre without water or cornering.
Get a manual do skids
Forum: Microtech
07-22-17, 06:33 AM
Replies: 31
Microtech Pump Settings
Views: 2,430
Posted By rx3sum

Try all of my figures first and if they dont work...

Try all of my figures first and if they dont work then you can make some adjustments.
I have based the figures off an experienced microtech tuners map.
I think your idle cell is too lean and the...
Forum: 20B Forum
07-22-17, 02:05 AM
Replies: 7
Views: 892
Posted By rx3sum

Give Hugh at Motor Elite a call.

Give Hugh at Motor Elite a call.
Forum: Microtech
07-21-17, 07:48 PM
Replies: 31
Microtech Pump Settings
Views: 2,430
Posted By rx3sum

Changing to TPS for pump 1 is setting pump1 stop...

Changing to TPS for pump 1 is setting pump1 stop to off.
I couldnt find much info on the net about how microtech does its calculations and interpolates etc and the people who know dont want to share...
Forum: Microtech
07-21-17, 02:53 AM
Replies: 31
Microtech Pump Settings
Views: 2,430
Posted By rx3sum

I had a look at your build thread and thats a...

I had a look at your build thread and thats a pretty amazing ride:icon_tup:
I do it a bit differently than Aaron and use pump1 off a vacumn setting and use pretty much what is in the basemap.I have...
Forum: Microtech
07-20-17, 03:49 AM
Replies: 31
Microtech Pump Settings
Views: 2,430
Posted By rx3sum

That matrix table is pretty messy:icon_tdow In...

That matrix table is pretty messy:icon_tdow
In my tune all cells from LOAD (4000)- 9000 are the same so fill those in.
There are lots of bumps in your matrix so flatten them out by adding fuel to...
Forum: Microtech
07-18-17, 03:48 AM
Replies: 31
Microtech Pump Settings
Views: 2,430
Posted By rx3sum

Just adjust the mixtrim and nothing else. I cant...

Just adjust the mixtrim and nothing else. I cant see your maps but it could be too lean or too rich after corrections to start on its own.
Adjusting mixtrim will tell you which way you need to be...
Forum: Microtech
07-17-17, 04:02 AM
Replies: 31
Microtech Pump Settings
Views: 2,430
Posted By rx3sum

I found the decel doesnt really work and results...

I found the decel doesnt really work and results in the engine cutting out and then cutting back in too harshly so ive turned mine off and manually tuned the decel cells.
Your water and crank maps...
Forum: Microtech
06-22-17, 02:30 AM
Replies: 5
Views: 1,482
Posted By rx3sum

Is it showing any errors? Whats your current...

Is it showing any errors?
Whats your current air temp settings?
Forum: Microtech
05-29-17, 03:43 AM
Replies: 10
Views: 900
Posted By rx3sum

In the menu there are some settings with either...

In the menu there are some settings with either MAP or TPS are all yours set to MAP?
Is the TPS calibrated at idle?
My car has no interior at the moment so cant check mine for at least a couple of...
Forum: Microtech
05-29-17, 03:40 AM
Replies: 10
Views: 900
Posted By rx3sum

double post

double post
Forum: Microtech
05-26-17, 06:12 PM
Replies: 10
Views: 900
Posted By rx3sum

The lights are discussed in the manual and yes...

The lights are discussed in the manual and yes its normal for it to crank for a second or so before firing.
Have you rebuilt the engine Lee?
Its idling way too rich if in the 10s or even the 11s...
Forum: Microtech
05-17-17, 03:27 AM
Replies: 4
Views: 1,218
Posted By rx3sum

According to the manual idle map should still be...

According to the manual idle map should still be the map it uses as long as the TPS is set correctly.
It sounds a little ghetto :egrin:but my tuner set idle and 1000 map with same values so if the...
Forum: Microtech
04-29-17, 03:45 AM
Replies: 1
Views: 711
Posted By rx3sum

If its just to get it to start up everything from...

If its just to get it to start up everything from the basemap except idle and load screens should be ok.
Idle and Load screens should be approx 50 to 60% of the values in the basemap prestage due to...
04-17-17, 04:05 AM
Replies: 6
Views: 1,428
Posted By rx3sum

From the mazda factory manual Apex seal width...

From the mazda factory manual
Apex seal width 3.0mm
Clearance of apex seal and rotor groove 0.05-0.09 mm Limit .15mm
04-04-17, 03:57 AM
Replies: 16
Views: 2,012
Posted By rx3sum

The right die is the only way to fix it. Take...

The right die is the only way to fix it.
Take the good nut with you and get the die.
Changing the thread pitch is not a good idea stick with the original size.
Forum: Microtech
03-10-17, 02:44 AM
Replies: 3
Views: 1,112
Posted By rx3sum

Who did the tuning and how well does it run?

Who did the tuning and how well does it run?
Forum: Microtech
02-17-17, 06:03 PM
Replies: 6
Views: 1,076
Posted By rx3sum

Ive only played with relatively standard engines...

Ive only played with relatively standard engines so am not much help.
You should take it straight to an experienced rotary dyno tuner as one small mistake could cost you an engine.
I can tell the...
Showing results 1 to 25 of 146
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.