RX7Club.com - Mazda RX7 Forum - Search Results

 
Search: Posts Made By: jdonnell
Showing results 1 to 25 of 465
Search took 0.38 seconds.
04-30-18, 07:00 PM
Replies: 1
Views: 328
Posted By jdonnell

I figured it out. Apparently the car had AC...

I figured it out. Apparently the car had AC issues in the past and the system was filled with R134a refrigerant. The car side connection has a conversion adapter R12 to R134a fitting. Using my R134...
04-29-18, 05:38 PM
Replies: 1
Views: 328
Posted By jdonnell

What A/C quick disconnect adapters do I need???

Hey guys, I was going to check the low side pressure to start diagnosing my air conditioner issue. When trying to connect the gauge set low side hose to the vehicle adapter, I realized the gauge set...
03-05-17, 09:54 AM
Replies: 0
Views: 294
Posted By jdonnell

Brake pedal return spring - anyone replace in car?

My brake pedal return spring is making a metallic springy sound in my FC and I'm afraid it is going to break. I looked up the part number B092-41-081 but is no longer available. Looking under the...
Forum: SE RX-7 Forum
02-27-17, 05:38 PM
Replies: 13
Views: 1,175
Posted By jdonnell

I work at Cape Canaveral and live in Indialantic...

I work at Cape Canaveral and live in Indialantic (20 miles south of Cocoa Beach). Indialantic is a nice place but the drive is too long because you only have 1 route basically down A1A. I drive 30...
01-10-17, 06:20 PM
Replies: 2
Views: 370
Posted By jdonnell

Be careful if you try and use the Moog mounts....

Be careful if you try and use the Moog mounts. The bearing internal diameter was too small on mine such that the lip on the upper strut plate did not fit in. KYB didn't have the bearing nor did...
11-29-16, 05:30 PM
Replies: 8
Views: 572
Posted By jdonnell

I finished the hub and axle removal and...

I finished the hub and axle removal and replacement about a week ago and been driving the car this week. No more noises from the rear with new wheel bearings I installed. I thought I'd give some tips...
11-11-16, 05:02 PM
Replies: 8
Views: 572
Posted By jdonnell

Hub and axle replacement was much more involved...

Hub and axle replacement was much more involved than I anticipated. Took all day to just to replace one side. Thanks for your help.....
11-11-16, 12:17 PM
Replies: 8
Views: 572
Posted By jdonnell

I got the hub off. Searched and tried a pickle...

I got the hub off. Searched and tried a pickle fork but it didn't really work for me. I used a propane torch to apply heat and using a flat head screwdriver moved the bushing outward. Worked great...
11-11-16, 12:00 PM
Replies: 8
Views: 572
Posted By jdonnell

Thanks guys. I ended up taking the rear strut out...

Thanks guys. I ended up taking the rear strut out and no problem whatsoever. However, that that upper bushing in the rear hub is a PITA preventing me from removing the hub. Any tips on that?...
11-11-16, 09:24 AM
Replies: 8
Views: 572
Posted By jdonnell

Rear axle removal?

Can you remove the convertible rear axle through the trailing arm opening without disconnecting the strut or separating the lateral link? I have the axle completely removed from the differential and...
09-06-16, 05:51 PM
Replies: 10
Views: 2,254
Posted By jdonnell

Nice write-up especially with the unclipping the...

Nice write-up especially with the unclipping the cable.
07-04-16, 11:50 AM
Replies: 1
Views: 417
Posted By jdonnell

Smile Super easy. Get a flat blade screw driver and...

Super easy. Get a flat blade screw driver and gently pry up the switch plastic baseplate. Pull switch upward and disconnect the connector. Install new switch. It's that easy. 5-10 minutes max.
01-17-16, 06:58 AM
Replies: 7
Views: 489
Posted By jdonnell

FSM shows a yellow wire and black / yellow wire...

FSM shows a yellow wire and black / yellow wire so I'll double-check to see if I can find it, but if not I'll have to punt today so I can finish my water pump and oil cooler lines.
01-16-16, 08:48 PM
Replies: 7
Views: 489
Posted By jdonnell

I guess I could hard wire with a switch if...

I guess I could hard wire with a switch if necessary but was hoping for just plug-n-play.
01-16-16, 04:36 PM
Replies: 7
Views: 489
Posted By jdonnell

Condensor Fan Harness Connector?

I have a 90 and 91 convertible that neither have a condensor fan. I bought a fan on e-bay and I was going to install it today on the 91, but I cant find the harness connector? I figure my cars had...
12-01-15, 05:09 PM
Replies: 30
Views: 2,147
Posted By jdonnell

Myself and Ray found out the same day when I...

Myself and Ray found out the same day when I tried to order parts last week. He had called me back and said they discontinued the franchise with Mazda and he just found out right then. He also said...
10-18-15, 10:20 AM
Replies: 42
Views: 6,789
Posted By jdonnell

Thumbs up I can't go but I wanted to support the event so I...

I can't go but I wanted to support the event so I bought a couple banners. Man they are nice!!! I was going to hang them in the garage but they are so nice I put them in the living room.
05-08-15, 03:20 PM
Replies: 569
Views: 139,834
Posted By jdonnell

0623113 was SOLD to new owner in TX.

0623113 was SOLD to new owner in TX.
04-15-15, 07:01 PM
Replies: 569
Views: 139,834
Posted By jdonnell

I'll probably be putting up my 0623113 for sale...

I'll probably be putting up my 0623113 for sale and thought I'd let you guys know in advance since your passionate about 10AEs like me. It has less than 19000 original miles and is babied with no...
02-14-15, 06:08 PM
Replies: 14
Views: 858
Posted By jdonnell

Can you tell us how you resolved the de-torque...

Can you tell us how you resolved the de-torque problem in case someone else runs into a similar problem?
02-14-15, 06:02 PM
Replies: 6
Views: 617
Posted By jdonnell

I think I fixed it but thanks I'll keep in mind...

I think I fixed it but thanks I'll keep in mind in case my fix does not last long. Window goes up and down now. I removed the regulator and guide rail and all the rollers were missing. I bought some...
02-08-15, 06:25 PM
Replies: 6
Views: 617
Posted By jdonnell

Thanks for your input. I did get the window and...

Thanks for your input. I did get the window and guide out but ran out of daylight for the regulator. You are right the quarter window does not have to come out when removing the window, but it was...
02-08-15, 11:24 AM
Replies: 3
Views: 624
Posted By jdonnell

Not sure if this is your solution but I use to...

Not sure if this is your solution but I use to get that code with Bosch O2 sensor installed. Switched to NTK and fixed the code.
02-08-15, 11:21 AM
Replies: 6
Views: 617
Posted By jdonnell

Convertible Regulator Removal & Replacement Sources

My window gets cocked going up / down and I need to remove the glass to replace the rollers and the regulator to grease and clean the cables. In the FSM (Page S-48) it says you need to remove the...
09-03-14, 05:50 PM
Replies: 35
Views: 2,595
Posted By jdonnell

The washer is called a 'Washer, Claw'. Mazda...

The washer is called a 'Washer, Claw'.
Mazda Part Number 1011-33-043.
Showing results 1 to 25 of 465
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.